This dissertation deals with the solution of three inverse problems in structural mechanics. The first one is load updating for finite element models (FEMs). A least squares fitting is used to identify the load parameters. The basic studies are made for geometrically linear and nonlinear FEMs of beams or frames by using a four-noded curved beam element, which, for a given precision, may significantly solve the ill-posed problem by reducing the overall number of degrees of freedom (DOF) of the system, especially the number of the unknown variables to obtain an overdetermined system. For the basic studies, the unknown applied load within an element is represented by a linear combination of integrated Legendre polynomials, the coefficients of which are the parameters to be extracted using measured displacements or strains. The optimizer L-BFGS-B is used to solve the least squares problem. The second problem is the placement optimization of a distributed sensing fiber optic sensor for a smart bed using Genetic Algorithms (GA), where the sensor performance is maximized. The sensing fiber optic cable is represented by a Non-uniform Rational B-Splines (NURBS) curve, which changes the placement of a set of infinite number of the infinitesimal sensors to the placement of a set of finite number of the control points. The sensor performance is simplified as the integration of the absolute curvature change of the fiber optic cable with respect to a perturbation due to the body movement of a patient. The smart bed is modeled as an elastic mattress core, which supports a fiber optic sensor cable. The initial and deformed geometries of the bed due to the body weight of the patient are calculated using MSC/NASTRAN for a given body pressure. The deformation of the fiber optic cable can be extracted from the deformation of the mattress. The performance of the fiber optic sensor for any given placement is further calculated for any given perturbation. The third application is stiffened panel optimization, including the size and placement optimization for the blade stiffeners, subject to buckling and stress constraints. The present work uses NURBS for the panel and stiffener representation. The mesh for the panel is generated using DistMesh, a triangulation algorithm in MATLAB. A NASTRAN/MATLAB interface is developed to automatically transfer the data between the analysis and optimization processes respectively. The optimization consists of minimizing the weight of the stiffened panel with design variables being the thickness of the plate and height and width of the stiffener as well as the placement of the stiffeners subjected to buckling and stress constraints under in-plane normal/shear and out-plane pressure loading conditions. / Ph. D.

O trabalho de doutorado teve como objetivo desenvolver um modulador óptico baseado em filme magnetostrictivo para aplicação como magnetômetro. A modelagem e simulação do dispositivo foi realizada utilizando software com cálculo por método dos elementos finitos (MEF) e teve como finalidade auxiliar iterativamente os processos de projeto e fabricação do modulador. A originalidade da proposta baseia-se na construção de um guia de onda em óptica integrada recoberto por um filme magnetostrictivo para permitir a modulação , via efeito elasto-óptico, da onda guiada pela aplicação de campos magnéticos externos. O campo magnético aplicado provoca a deformação o material magnetostrictivo que induz uma modificação no perfil de esforço aplicado ao substrato. O substrato tem suas propriedades ópticas alteradas devido ao efeito elasto-óptico, o que provoca mudanças nas propriedades da luz transmitida. O trabalho tem seu início com o estudo e a caracterização de filmes magnetostrictivos de Tb25F275 e Tb23Co77 depositados por sputtering sobre substratos de silício. Uma técnica para preparação das amostras e medição da magnetostricção foi estabelecida e os coeficientes de magnetostrição dos filmes foram determinados a partir das medições diretas dos deslocamentos das amostras, em função dos campos magnéticos aplicados, utilizando a técnica de Atomic Force Microscopy (AFM). Os resultados experimentais obtidos permitiram a realização de simulações por MEF para verificação dos modos de guiamento da luz gerados pelo perfil de esforços induzidos termicamente no processo de deposição do filme magnetostrictivo sobre substrato de B12GeO4 (BGO). Foi modelado e simulado também o efeito da aplicação do campo magnético sobre o guia óptico obtido inicialmente pelo efeito de esforço térmico. No resultado das simulações foi possível verificar as alterações do índice de refração efetivo e da intensidade óptica do modo guiado em função de campos magnéticos aplicados ao modulador. Ao final do trabalho realizaram-se a fabricação de alguns protótipos. Os resultados das caracterizações dos moduladores construídos permitirão, no futuro, ajustar os modelos de simulação elaborados. / The doctoral work aims are the development and simulation of an optical modulator based on the effect of magnetostriction for application as magnetometer. The multiphysics simulations were performed using the Finite Elements Method (FEM). In the manufacturing process of optical modulator integrated optics techniques were applied. The originality of the proposal is based on the construction of an integrated optical waveguide covered by a magnetostrictive film to allow the modulation of the guided wave, through the elasto-optical effect, by the application of external magnetic fields. The applied magnetic field causes deformation of the magnetostrictive material that induces a modification of the stress profile produced in substrate. The substrate has its optical properties altered due to the elasto-optical effect, which causes changes in the properties of transmitted light. The work begins with the study and characterization of TbFe and TbCo2 magnetostrictive films deposited by sputtering on silicon substrates. A method for sample preparation and measurement of magnetostriction was established. The magnetostrictive coefficient of the films was determined from the direct measurement of displacements of samples by AFM technique for magnetic fields applied. The experimental results obtained allowed to perform MEF simulations to verify the light guided modes generated by the profile of thermally induced stress created by deposition process of magnetostrictive film on B12GeO4 (BGO) substrate. It was also modeled and simulated the effect of the application of magnetic field on the optical guide obtained initially by the effect of thermal stress. In simulation results, it was possible to verify the changes of effective refractive index and optical intensity of guided modes as functions of magnetic fields applied to the modulator. At the end of the work, some prototypes were fabricated. The results of characterizations of the built modulators will allow, in the future, adjustments in simulation models.

O trabalho de doutorado teve como objetivo desenvolver um modulador óptico baseado em filme magnetostrictivo para aplicação como magnetômetro. A modelagem e simulação do dispositivo foi realizada utilizando software com cálculo por método dos elementos finitos (MEF) e teve como finalidade auxiliar iterativamente os processos de projeto e fabricação do modulador. A originalidade da proposta baseia-se na construção de um guia de onda em óptica integrada recoberto por um filme magnetostrictivo para permitir a modulação , via efeito elasto-óptico, da onda guiada pela aplicação de campos magnéticos externos. O campo magnético aplicado provoca a deformação o material magnetostrictivo que induz uma modificação no perfil de esforço aplicado ao substrato. O substrato tem suas propriedades ópticas alteradas devido ao efeito elasto-óptico, o que provoca mudanças nas propriedades da luz transmitida. O trabalho tem seu início com o estudo e a caracterização de filmes magnetostrictivos de Tb25F275 e Tb23Co77 depositados por sputtering sobre substratos de silício. Uma técnica para preparação das amostras e medição da magnetostricção foi estabelecida e os coeficientes de magnetostrição dos filmes foram determinados a partir das medições diretas dos deslocamentos das amostras, em função dos campos magnéticos aplicados, utilizando a técnica de Atomic Force Microscopy (AFM). Os resultados experimentais obtidos permitiram a realização de simulações por MEF para verificação dos modos de guiamento da luz gerados pelo perfil de esforços induzidos termicamente no processo de deposição do filme magnetostrictivo sobre substrato de B12GeO4 (BGO). Foi modelado e simulado também o efeito da aplicação do campo magnético sobre o guia óptico obtido inicialmente pelo efeito de esforço térmico. No resultado das simulações foi possível verificar as alterações do índice de refração efetivo e da intensidade óptica do modo guiado em função de campos magnéticos aplicados ao modulador. Ao final do trabalho realizaram-se a fabricação de alguns protótipos. Os resultados das caracterizações dos moduladores construídos permitirão, no futuro, ajustar os modelos de simulação elaborados. / The doctoral work aims are the development and simulation of an optical modulator based on the effect of magnetostriction for application as magnetometer. The multiphysics simulations were performed using the Finite Elements Method (FEM). In the manufacturing process of optical modulator integrated optics techniques were applied. The originality of the proposal is based on the construction of an integrated optical waveguide covered by a magnetostrictive film to allow the modulation of the guided wave, through the elasto-optical effect, by the application of external magnetic fields. The applied magnetic field causes deformation of the magnetostrictive material that induces a modification of the stress profile produced in substrate. The substrate has its optical properties altered due to the elasto-optical effect, which causes changes in the properties of transmitted light. The work begins with the study and characterization of TbFe and TbCo2 magnetostrictive films deposited by sputtering on silicon substrates. A method for sample preparation and measurement of magnetostriction was established. The magnetostrictive coefficient of the films was determined from the direct measurement of displacements of samples by AFM technique for magnetic fields applied. The experimental results obtained allowed to perform MEF simulations to verify the light guided modes generated by the profile of thermally induced stress created by deposition process of magnetostrictive film on B12GeO4 (BGO) substrate. It was also modeled and simulated the effect of the application of magnetic field on the optical guide obtained initially by the effect of thermal stress. In simulation results, it was possible to verify the changes of effective refractive index and optical intensity of guided modes as functions of magnetic fields applied to the modulator. At the end of the work, some prototypes were fabricated. The results of characterizations of the built modulators will allow, in the future, adjustments in simulation models.

Sensors have become essential elements in human life for safe and comfortable existence in the ever demanding world. Various technologies over decades have contributed in their own way fulfilling innumerable sensing requirements. The discovery of optical sensor technologies has revolutionized the sensing field due to their inherent advantages. Among the large number of fiber optic sensor technologies, FBG based sensors have become widely known and popular within and outside the photonics community and has seen a prominent rise in their utilization. This thesis explores the use of FBG sensors for a wide range of applications scanning across a variety of engineering and medical applications, in the areas of civil engineering, biomechanical engineering, aerospace engineering, geoengineering, etc. It also deals with newer methods of packaging FBG sensors for the measurement of specific engineering parameters like strain, temperature, pressure, displacement and vibration. In the field of civil engineering, FBG sensors are employed for strain sensing on a prism and furthermore tested on a full size brick wallet. During this study, emphasis is made on substituting traditional sensors by specially packaged FBG sensors with the intent of either enhancing the sensing system’s performance or in merging/uniting the inherent advantages of FBG sensors. In the area of biomechanics, a novel sensor methodology using FBG sensors, for measuring surface strains generated on the skin of the calf muscle during various leg exercises is proposed. This methodology is used to address one of the most critical and life threatening issues in long distance air travel, namely the Deep Vein Thrombosis. Further, a FBG sensor based plantar sensing plate, is designed and developed, to measure plantar strain distribution in foot and also to analyze the postural stability. In the field of aerospace engineering, FBG sensors are used for addressing two of the most vital issues; Structural Health Monitoring (SHM) and direct measurement of pressure and temperature on the surface of an aircraft under hypersonic wind flow. Carbon Fiber Composite coupon level testing is carried out to obtain a generic strain calibration factor for the FBG sensor. Further, FBG sensors are exploited for the direct measurement of absolute temperature and pressure on the leeward surface of blunt cone at hypersonic wind speeds. In the domain of geoengineering, the feasibility studies have been undertaken to use a FBG as a seismic sensor and as a bore-well characterizing sensor. A novel FBG seismic sensor package is developed using a single FBG sensor to pick up the seismic waves propagating through the ground generated from earthquakes and ground tremors. Further, FBG sensors are used for measurement of temperature profiles in a bore-well to delineate and characterize the behavior of fractures during seasonal climatic changes. To summarize, the present thesis demonstrates a comprehensive experimental study which bring out the utility of FBG sensors in a variety of challenging applications.

This thesis deals with the influence microbending the transmitted signal at the bare optical fiber. Microbending influence on the transmitted signal is investigated in this work by changing the weight, power and water level in the tank by using this test fixture. The results of the experiments are proposed to enter the laboratory tasks to measure the impact microbending the transmitted signal in the subject line fiber-optic sensors (MOES).

Beneath North America's roads lie 1.6 million miles of pipeline that provides users with potable water and carry away wastewater. These buried infrastructure systems have been functioning for duration longer than their intended design life, often with little or no repair. Asset management of pipeline systems pose a major challenge for most municipalities due to budgetary constraints, demand for quality service, and need to preserve existing pipeline infrastructure. The first step in developing and implementing a comprehensive asset management plan is to perform a condition assessment. There is a gamut of inspection and monitoring technologies available to enable the condition assessment of pipelines. All of these have advantages and limitations, which determine the performance quality and effectiveness of an individual technology for particular utility assets. Unfortunately, utilities choose technologies not suitable for their specific assets and collect data that is not useful for understanding the condition of their system. The objective of this thesis is to develop a framework for the effective selection of condition assessment technologies for water and wastewater utilities. A Microsoft-Excel based framework is developed to help the utility managers in selecting condition assessment technologies for their water and wastewater pipeline assets. The recommended tool selection approach uses a multi-step exclusion protocol in which the tools are excluded on the basis of their applicability relating to technical feasibility and technical suitability for a particular situation. Usable tools are then compared against a performance and cost database to determine performance and cost in a given project/ utility condition. This thesis provides a brief description and review of 24 non-destructive commercialized condition assessment technologies, including the principal and implementation considerations. A framework for decision system tool was developed to facilitate utilities in selecting appropriate condition assessment technologies. This framework could facilitate the selection of usable technologies by excluding the options which are not technically feasible and suitable. The user can then further explore the usable tools and determine the most suitable technologies for their assets. The data considered in the research is provided by technology providers, thus it may lack complete understanding of the capabilities and limitations of technology. This thesis also presents a case study which highlights the existing gap between the understanding of capabilities and limitations of various technologies. A program is developed as a part of this thesis, Condition Assessment Selection Tool (CAST), which consists of performance and economic database, a graphical user interface to facilitate user input, and the results of the comparison of each usable technology in the database to the project information provided by the user for their assets. The results are presented as performance indices and economic indices indicating the performance and technology cost of usable technologies. A data reliability index was also developed to provide a scale for comparing the reliability of the existing data in the database. / Master of Science

Hydrogen peroxide (H2O2) is extensively used in a broad range of industrial and medical applications, such as aseptic processing of food and pharmaceuticals, disinfection, water treatment plants, and decontamination of industrial effluents. H2O2 is believed to be responsible for chemical degradation of polymer membranes in Polymer-Electrolyte-Membrane (PEM) fuel cells. Therefore, a versatile H2O2 sensor that functions in different environments with different conditions is of practical importance in various fields. This dissertation presents the fabrication of a fiber-optic H2O2 sensing probe (optrode) and its H2O2 sensing behavior in different conditions. An H2O2 optrode is fabricated using chemical deposition of Prussian blue (PB) onto the tip of a multimode optical fiber. Sensing tests are performed in aqueous solutions at a constant pH and different concentrations of H2O2. Sensing features of the optrode (i.e. repeatability, durability, and reproducibility) are assessed by performing multiple sensing tests with several optrodes. The results show the prepared optrode is able to detect concentrations of H2O2 in aqueous solutions at a constant pH of 4 and the optrode features a repeatable and durable response at this condition. The functionality of optrodes at different pH values is further investigated by performing additional sensing experiments. These experiments are carried out in aqueous solutions with different concentrations of H2O2 at different pH values (i.e. pH 2-7). The sensor detects the presence of H2O2 at a range of pH values. Sensing behavior of optrodes toward detection and measurement of H2O2 concentrations is studied at the pH value corresponding to an operating PEM fuel cell (i.e. pH 2). The optrode is able to detect concentrations of H2O2 at this condition with a repeatable and durable response. The stability of PB films, prepared through different conditions, is investigated to address the stability of optrodes at elevated temperatures. PB films are first deposited onto the glass slides through three different chemical processes, and then at different synthesis temperatures. The PB films are left in Phosphate-Buffer-Solutions (PBS) with pH 2 and at elevated temperatures for a day. Finally, PB films are characterized using Fourier transform infrared spectroscopy (FTIR) to analyze their stability following PBS processing at operating temperatures and pH value corresponding to an operating PEM fuel cell (i.e. 80 °C and pH 2). The results of these experiments illustrate the PB films prepared through the single-source precursor (SSP) technique and at synthesis temperatures above 60 °C remain stable after the PBS processing. The proposed optrode shows reliable sensing behavior toward detection and measurement of H2O2 concentrations in aqueous solutions at different conditions. The prepared optrode has the potential for being developed and used in different industrial and medical fields, as well as an operating PEM fuel cell, to detect and measure H2O2 concentrations. / Graduate / 0794 / 0548 / 0485 / hakbarik@uvic.ca

L'objectif de cette thèse est d'étudier des variations de composition de verres ou l'intégration de nanostructures métalliques pouvant présenter un intérêt pour les capteurs à fibres optiques répartis (CFO). Ces capteurs utilisent le coeur des fibres optiques constitué majoritairement de silice (SiO2) pour sonder la température ou les déformations sur des parcours plurikilométriques de fibres. A cette fin, les rétrodiffusions Raman et Brillouin dans les fibres optiques sont utilisées, la diffusion Raman étant sensible aux variations de température et la diffusion Brillouin aux variations de température et de déformation. L'intensité de diffusion Raman peut-être exaltée au contact de nanostructures de métaux nobles, par l'intermédiaire de l'effet SERS (Diffusion Raman Exaltée de Surface) faisant intervenir notamment la résonance plasmon de surface (SPR), oscillation collective des électrons libres à la surface métallique générant une large amplification du champ électrique local. L'intégration de nanostructures métalliques dans les fibres optiques pourrait permettre d'augmenter l'intensité de rétrodiffusion Raman et améliorer les performances des CFO (sensibilité, temps d'intégration…). Une étude sur des échantillons modèles, constitués de substrats SERS nanostructurés d'or et recouvert de silice par dépôt sol-gel, est présentée dans ce manuscrit. Les résultats SERS ainsi obtenus permettent de caractériser le phénomène physique du SERS de SiO2 et de prédire sa potentielle utilité dans les CFO Raman / The purpose of this thesis is to study composition variations of silicate glasses or the integration of metallic nanostructures that may be relevant for distributed fiber optic sensors (FOS). These sensors use optical fiber cores mainly composed of silica (SiO2) to probe temperature or strain on multi-kilometer route fibers. To measure these effects, Raman and Brillouin backscattering in optical fibers are used, Raman scattering being sensitive to temperature variations and Brillouin scattering to temperature and strain variations. Raman scattering intensity may be enhanced in conjunction with noble metal nanostructures via the SERS effect (Surface Enhanced Raman Scattering) which involves surface plasmon resonance (SPR), a collective oscillation of free electrons at the metal surface generating a large amplification of the local electric field. The integration of metallic nanostructures in optical fibers could increase Raman backscattering intensity and improve FOS performance (sensitivity, integration time…). A study on model samples has been performed with SERS substrates consisting of gold nanostructures and coated with a sol-gel oxide deposition (TiO2, SiO2). The obtained SERS results are used to predict the contribution of metallic nanostructures in Raman distributed temperature FOS

Spectrally-based fiber optic sensors are a rapidly maturing technology capable of sensing several environmental parameters in environments that are unfitting to electrical sensors. However, the sensor interrogation systems for this type of sensors are not yet fit to replace conventional sensor systems. They lack the speed, compact size, and usability necessary to move into mainstream test and measurement. The Fiber Sensor Integrated Monitor (FSIM) technology leverages rapid optical components and parallel hardware architecture to move these sensors across the research threshold into greater mainstream use. By dramatically increasing speed, shrinking size, and targeting an interface that can be used in large-scale industrial interrogation systems, spectrally-based fiber optic sensors can now find more widespread use in both research labs and industrial applications. The technology developed in this thesis was demonstrated by producing two advanced interrogators: one that was one half the size of commercially available systems, and one that accelerated live spectral capture by one thousand times – both of which were operated by non-developers with little training.

In this thesis work, a systematic quantitative study has been undertaken, on the performance of etched fiber Bragg Grating (FBG) sensors in the investigation of surface molecular adsorption in real-time; it is shown that the limit of detection (LOD) of FBGs etched below 2 microns diameter, is better compared to prominent optical label-free molecular sensing techniques such as Surface Plasmon Resonance (SPR). Novel fiber optic sensors based on FBG and etched FBG with various nano materials (polyelectrolytes, carbon nanotubes, hydrogel, metals and chalcogenides) coated on the surface of the core or cladding, have been proposed for sensing multi parameters such as pH, protein, humidity, gas, strain, temperature, and light etc. Besides being reproducible and repeatable, the proposed methods are fast, compact, and highly sensitive. A novel optical instrument has also been developed to measure angular deviation, binocular deviation and refractive index of glass slabs, and liquids, based on a shadow casting technique. This method uses the deviation in the geometrical shadow cast by a periodic dot pattern trans-illuminated by a distorted light beam from the transparent test specimen relative to a reference pattern.