No description available.

No description available.

No description available.

No description available.

No description available.

One way to increase cycle efficiency of a gas turbine engine is to operate at higher turbine inlet temperature (TIT). In most engines, the turbine inlet temperatures have increased to be well above the metallurgical limit of engine components. Film cooling of gas turbine components (blades and vanes) is a widely used technique that allows higher turbine inlet temperatures by maintaining material temperatures within acceptable limits. In this cooling method, air is extracted from the compressor and forced through internal cooling passages within turbine blades and vanes before being ejected through discrete cooling holes on the surfaces of these airfoils. The air leaving these cooling holes forms a film of cool air on the component surface which protects the part from hot gas exiting the combustor. Design optimization of the airfoil film cooling system on an engine scale is a key as increasing the amount of coolant supplied yields a cooler airfoil that will last longer, but decreases engine core flow—diminishing overall cycle efficiency. Interestingly, when contemplating the physics of film cooling, optimization is also a key to developing an effective design. The film cooling process is shown to be a complex function of at least two important mechanisms: Increasing the amount of coolant injected reduces the driving temperature (adiabatic wall temperature) of convective heat transfer—reducing heat load to the airfoil, but coolant injection also disturbs boundary layer and augments convective heat transfer coefficient due to local increase in freestream turbulence. Accurate numerical modeling of airfoil film cooling performance is a challenge as it is complicated by several factors such as film cooling hole shape, coolant-to-freestream blowing ratio, coolant-to-freestream momentum ratio, surface curvature, approaching boundary layer state, Reynolds number, Mach number, combustor-generated high freestream turbulence, turbulence length scale, and secondary flows just to name a few. Until computational methods are able to accurately simulate these factors affecting film cooling performance, experimental studies are required to assist engineers in designing effective film cooling schemes. The unique contribution of this research work is to experimentally and numerically investigate the effects of coolant injection rate or blowing ratio and exit Reynolds number/Mach number on the film cooling performance of a showerhead film cooled first stage turbine vane at high freestream turbulence (Tu = 16%) and engine representative exit flow conditions. The vane was arranged in a two-dimensional, linear cascade in a heated, transonic, blow-down wind tunnel. The same facility was also used to conduct experimental and numerical study of the effects of freestream turbulence, and Reynolds number on smooth (without film cooling holes) turbine blade and vane heat transfer at engine representative exit flow conditions. The showerhead film cooled vane was instrumented with single-sided platinum thin film gauges to experimentally determine the Nusselt number and film cooling effectiveness distributions over the surface from a single transient-temperature run. Showerhead film cooling was found to augment Nusselt number and reduce adiabatic wall temperature downstream of injection. The adiabatic effectiveness trend on the suction surface was also found to be influenced by a favorable pressure gradient due to Mach number and boundary layer transition region at all blowing ratio and exit Mach number conditions. The experimental study was also complimented with a 3-D CFD effort to calculate and explain adiabatic film cooling effectiveness and Nusselt number distributions downstream of the showerhead film cooling rows of a turbine vane at high freestream turbulence (Tu = 16%) and engine design exit flow condition (Mex = 0.76). The research work presents a new three-simulations technique to calculate vane surface recovery temperature, adiabatic wall temperature, and surface Nusselt number to completely characterize film cooling performance in a high speed flow. The RANS based v2-f turbulence model was used in all numerical calculations. CFD calculations performed with experiment-matched boundary conditions showed an overall good trend agreement with experimental adiabatic film cooling effectiveness and Nusselt number distributions downstream of the showerhead film cooling rows of the vane. / Ph. D.

The contribution of present research work is to experimentally investigate the effects of blowing ratio and mainstream Mach number/Reynolds number (from 0.6/8.5X10⁵ to 1.0/1.4X10⁶) on the performance of the fan-shaped hole injected turbine blade and vane. The study was operated with high freestream turbulence intensity (12% at the inlet) and large turbulence length scales (0.26 for blade, 0.28 for vane, normalized by the cascade pitch of 58.4mm and 83.3mm respectively). Both convective heat transfer coefficient, in terms of Nusselt number, and adiabatic effectiveness are provided in the results. Present research work also numerically investigates the shock/film cooling interaction. A detailed analysis on the physics of the shock/film cooling interaction in the blade cascade is provided. The results of present research suggests the following major conclusions. Compared to the showerhead only vane, the addition of fan-shaped hole injection on the turbine Nozzle Guide Vane (NGV) increases the Net Heat Flux Reduction (NHFR) 2.6 times while consuming 1.6 times more coolant. For the blade, combined with the surface curvature effect, the increase of Mach number/Reynolds number results in an improved film cooling effectiveness on the blade suction side, but a compromised cooling performance on the blade pressure side. A quick drop of cooling effectiveness occurs at the shock impingement on the blade suction side near the trailing edge. The CFD results indicate that this adiabatic effectiveness drop was caused by the strong secondary flow after shock impingement, which lifts coolant away from the SS surface, and increases the mixing. This secondary flow is related to the spanwise non-uniform of the shock impingement. / Ph. D.

The thermal efficiency of a gas turbine directly depends on the rotor inlet temperature. The ever increasing demand for more power and advances in the field of engineering enabled this temperature to be pushed higher. But the material strength of the blades and vanes can often impose restrictions on the thermal load it can bear. This is where gas turbine cooling becomes very critical and a better cooling design has the potential to extend the blade life span, enables higher rotor inlet temperatures, conserves compressor bleed air. Among various kinds of cooling involved in gas turbines, film cooling will be the subject of this study. A novel concept for film cooling holes referred to as anti-vortex design proposed in 2007 is explored in this study. Coolant exits through two bifurcated cylindrical holes that branched out on either side of the central hole resulting in a tripod-like arrangement. Coolant from the side holes interacted with the mainstream and produced vortices that countered the main central rotating vortex pairs, weakening it and pushing the coolant jet towards the surface. In order to understand the performance of this anti-vortex tripod film cooling, a flat plate test setup and a low speed subsonic wind tunnel linear cascade were built. Transient heat transfer experiments were carried out in the flat plate test setup using Infrared thermography. Film cooling performance was quantified by measuring adiabatic effectiveness and heat transfer coefficient ratio. In order to gauge the performance, other standard hole geometries were also tested and compared with. Following the results from the flat plate test rig, film cooling performance was also evaluated on the surface of an airfoil. Adiabatic effectiveness was measured at different coolant mass flow rates. The tripod hole consistently provided better cooling compared to the standard cylindrical hole in both the flat plate and cascade experiments. In order to understand the anti-vortex concept which is one of the primary reason behind better performance of the tripod film cooling hole geometry, numerical simulations (CFD) were carried out at steady state using RANS turbulence models. The interaction of the coolant from the side holes with the mainstream forms vortices that tries to suppress the vortex formed by the central hole. This causes the coolant jet from the central to stay close to the surface and increases its coverage. Additionally, the coolant getting distributed into three individual units reduces the exit momentum ratio. Tripod holes were found to be capable of providing better effectiveness even while consuming almost half the coolant used by the standard cylindrical holes. / Ph. D.

In the past few decades, the operating temperatures of gas turbine engines have increased significantly with a view towards increasing the overall thermal efficiency and specific power output. As a result of increased turbine inlet temperatures, the hot gas path components downstream of the combustor section are subjected to high heat loads. Though materials with improved temperature capabilities are used in the construction of the hot gas path components, in order to ensure safe and durable operation, the hot gas path components are additionally supplemented with thermal barrier coatings (TBCs) and sophisticated cooling techniques. The present study focusses on two aspects of gas turbine cooling, namely augmented internal cooling and external film cooling. One of the commonly used methods for cooling the vanes involves passing coolant air bled from the compressor through serpentine passages inside the airfoils. The walls of the internal cooling passages are usually roughened with turbulence promoters like ribs to enhance heat transfer. Though the ribs help in augmenting the heat transfer, they have an associated pressure penalty as well. Therefore, it is important to study the thermal-hydraulic performance of ribbed internal cooling passages. The first section of the thesis deals with the numerical investigation of flow and heat transfer characteristics in a ribbed two-pass channel. Four different rib shapes- 45° angled, V-shaped, W-shaped and M-shaped, were studied. This study further aims at exploring the performance of different rib-shapes at a large rib pitch-to-height ratio (p/e=16) which has potential applications in land-based gas turbines operating at high Reynolds numbers. Detailed flow and heat transfer analysis have been presented to illustrate how the innate flow physics associated with the bend region and the different rib shapes contribute to heat transfer enhancement in the two-pass channel. The bend-induced secondary flows were observed to significantly affect the flow and heat transfer distribution in the 2nd pass. The thermal-hydraulic performance of V-shaped and 45° angled ribs were better than W-shaped and M-shaped ribs. The second section of the study deals with the analysis of film cooling performance of different hole configurations on the endwall upstream of a first stage nozzle guide vane. The flow along the endwall of the airfoils is highly complex, dominated by 3-dimensional secondary flows. The presence of complex secondary flows makes the cooling of the airfoil endwalls challenging. These secondary flows strongly influence endwall film cooling and the associated heat transfer. In this study, three different cooling configurations- slot, cylindrical holes and tripod holes were studied. Steady-state experiments were conducted in a low speed, linear cascade wind tunnel. The adiabatic film cooling effectiveness on the endwall was computed based on the spatially resolved temperature data obtained from the infrared camera. The effect of mass flow ratio on the film cooling performance of the different configurations was also explored. For all the configurations, the coolant jets were unable to overcome the strong secondary flows inside the passage at low mass flow ratios. However, the coolant jets were observed to provide much better film coverage at higher mass flow ratios. In case of cylindrical ejection, the effectiveness values were observed to be very low which could be because of jet lift-off. The effectiveness of tripod ejection was comparable to slot ejection at mass flow ratios between 0.5-1.5, while at higher mass flow ratios, slot ejection was observed to outperform tripod ejection. / Master of Science

Aircraft engine manufacturers strive for greater performance and efficiency by continually increasing the turbine inlet temperature. High turbine inlet temperatures significantly degrade the lifetime of components in the turbine. Modern gas turbines operate with turbine inlet temperatures well above the melting temperature of key turbine components. Without active cooling schemes, modern turbines would fail catastrophically. This study will evaluate a novel cooling scheme for turbine airfoils, called microcircuit cooling, in which small cooling channels are located extremely close to the surface of a turbine airfoil. Coolant bled from the compressor passes through the microcircuits and exits through film cooling slots. On further cooling benefit is that the microcircuit passages are filled with irregular pin fin features that serve to increase convective cooling through the channels. Results from this study indicate a strong interaction between the internal microcircuit features and the external film-cooling from the slot exit. Asymmetric cooling patterns downstream of the slot resulted from the asymmetric pin fin design within the microcircuit. Adiabatic effectiveness levels were found to be optimum for the slot design at a blowing ratio of 0.37. The pin fin arrangement along with the impingement cooling at the microcircuit entrance increased the area-averaged heat transfer by a factor of three, relative to an obstructed channel, over a Reynolds range of 5,000 to 15,000. / Master of Science