In the drive to increase cycle efficiency, gas turbine designers have increased turbine inlet temperatures well beyond the metallurgical limits of engine components. In order to prevent failure and meet life requirements, turbine components must be cooled well below these hot gas temperatures. Film cooling is a widely employed cooling technique whereby air is extracted from the compressor and ejected through holes on the surfaces of hot gas path components. The cool air forms a protective film around the surface of the part. Accurate numerical prediction of film cooling performance is extremely difficult so experiments are required to validate designs and CFD tools. In this study, a first stage turbine vane with five rows of showerhead cooling was instrumented with platinum thin-film gauges to experimentally characterize film cooling performance. The vane was tested in a transonic vane cascade in Virginia Tech's heated, blow-down wind tunnel. Two freestream exit Mach numbers of 0.76 and 1.0—corresponding to exit Reynolds numbers based on vane chord of 1.1x106 and 1.5x106, respectively—were tested at an inlet freestream turbulence intensity of two percent and an integral length scale normalized by vane pitch of 0.05. The showerhead cooling scheme was tested at blowing ratios of 0 (no cooling), 1.5, and 2.0 and a density ratio of 1.35. Midspan Nusselt number and film cooling effectiveness distributions over the surface of the vane are presented. Film cooling was found to augment heat transfer and reduce adiabatic wall temperature downstream of injection. In general, an increase in blowing ratio was shown to increase augmentation and film cooling effectiveness. Increasing Reynolds number was shown to increase heat transfer and reduce effectiveness. Finally, comparing low turbulence measurements (Tu = 2%) to measurements performed at high freestream turbulence (Tu = 16%) by Nasir et al. [13] showed that large-scale high freestream turbulence can reduce heat transfer coefficient downstream of injection. / Master of Science

The goal of a gas turbine engine designer is to reduce the amount of coolant used to cool the critical turbine surfaces, while at the same time extracting more benefit from the coolant flow that is used. Fan-shaped holes offer this opportunity, reducing the normal jet momentum and spreading the coolant in the lateral direction providing better surface coverage. The main drawback of fan-shaped cooling holes is the added manufacturing cost from the need for electrical discharge machining instead of the laser drilling used for cylindrical holes. This research focused on examining the performance of fan-shaped holes on two critical turbine surfaces; the vane and endwall. This research was the first to offer a complete characterization of film-cooling on a turbine vane surface, both in single and multiple row configurations. Infrared thermography was used to measure adiabatic wall temperatures, and a unique rigorous image transformation routine was developed to unwrap the surface images. Film-cooling computations were also done comparing the performance of two popular turbulence models, the RNG-kε and the v2-f model, in predicting film-cooling effectiveness. Results showed that the RNG-kε offered the closest prediction in terms of averaged effectiveness along the vane surface. The v2-f model more accurately predicted the separated flow at the leading edge and on the suction side, but did not predict the lateral jet spreading well, which led to an over-prediction in film-cooling effectiveness. The intent for the endwall surface was to directly compare the cooling and aerodynamic performance of cylindrical holes to fan-shaped holes. This was the first direct comparison of the two geometries on the endwall. The effect of upstream injection and elevated inlet freestream turbulence was also investigated for both hole geometries. Results indicated that fan-shaped film-cooling holes provided an increase in film-cooling effectiveness of 75% on average above cylindrical film-cooling holes, while at the same time producing less total pressure losses through the passage. The effect of upstream injection was to saturate the near wall flow with coolant, increasing effectiveness levels in the downstream passage, while high freestream turbulence generally lowered effectiveness levels on the endwall. / Ph. D.

The effect of global warming due to increased level of greenhouse gas emissions from coal fired thermal power plants and crisis of reliable energy resources has profoundly increased the importance of natural gas based power generation as a major alternative in the last few decades. Although gas turbine propulsion system had been primarily developed and technological advancements over the years had focused on application in civil and military aviation industry, use of gas turbine engines for land based power generation has emerged as the most promising candidate due to higher thermal efficiency, abundance of natural gas resources, development in generation of hydrogen rich synthetic fuel (Syngas) using advanced gasification technology for further improved emission levels and strict enforcement in emission regulations on installation of new coal based power plants. The fundamental thermodynamic principle behind gas turbine engines is Brayton cycle and higher thermal efficiency is achieved through maximizing the Turbine Inlet Temperature (TIT). Modern gas turbine engines operate well beyond the melting point of the turbine component materials to meet the enhanced efficiency requirements especially in the initial high pressure stages (HPT) after the combustor exit. Application of thermal barrier coatings (TBC) provides the first line of defense to the hot gas path components against direct exposure to high temperature gases. However, a major portion of the heat load to the airfoil and passage is reduced through injection of secondary air from high pressure compressor at the expense of a penalty on engine performance. External film cooling comprises a significant part of the entire convective cooling scheme. This can be achieved injecting coolant air through film holes on airfoil and endwall passages or utilizing the high pressure air required to seal the gaps and interfaces due to turbine assembly features. The major objective is to maximize heat transfer performance and film coverage on the surface with minimum coolant usage. Endwall contouring on the other hand provides an effective means of minimizing heat load on the platform through efficient control of secondary flow vortices. Complex vortices form due to the interaction between the incoming boundary layer and endwall-airfoil junction at the leading edge which entrain the hot gases towards the endwall, thus increasing surface heat transfer along its trajectory. A properly designed endwall profile can weaken the effects of secondary flow thereby improving the aerodynamic and associated heat transfer performance. This dissertation aims to investigate heat transfer characteristics of a non-axisymmetric contoured endwall design compared to a baseline planar endwall geometry in presence of three major endwall cooling features – upstream purge flow, discrete hole film cooling and mateface gap leakage under transonic operating conditions. The preliminary design objective of the contoured endwall geometry was to minimize stagnation and secondary aerodynamic losses. Upstream purge flow and mateface gap leakage is necessary to prevent ingestion to the turbine core whereas discrete hole cooling is largely necessary to provide film cooling primarily near leading edge region and mid-passage region. Different coolant to mainstream mass flow ratios (MFR) were investigated for all cooling features at design exit isentropic Mach number (0.88) and design incidence angle. The experiments were performed at Virginia Tech's quasi linear transonic blow down cascade facility. The airfoil span increases in the mainstream flow direction in order to match realistic inlet/exit airfoil surface Mach number distribution. A transient Infrared (IR) thermography technique was employed to measure the endwall surface temperature and a novel heat transfer data reduction method was developed for simultaneous calculation of heat transfer coefficient (HTC) and adiabatic cooling effectiveness (ETA), assuming a 1D semi-infinite transient conduction. An experimental study on endwall film cooling with endwall contouring at high exit Mach numbers is not available in literature. Results indicate significant benefits in heat transfer performance using the contoured endwall in presence of individual (upstream slot, discrete hole and mateface gap) and combined (upstream slot with mateface gap) cooling flow features. Major advantages of endwall contouring were observed through reduction in heat transfer coefficient and increase in coolant film coverage by weakening the effects of secondary flow and cross passage pressure differential. Net Heat Flux Reduction (NHFR) analysis was carried out combining the effect of heat transfer coefficient and film cooling effectiveness on both endwall geometries (contoured and baseline) where, the contoured endwall showed major improvement in heat load reduction near the suction side of the platform (upstream leakage only and combined upstream with mateface leakage) as well as further downstream of the film holes (discrete hole film cooling). Detailed interpretation of the heat transfer results along with near endwall flow physics has also been discussed. / Ph. D.

The unsteady interaction of shock waves emerging from the trailing edge of modern turbine nozzle guide vanes and impinging on downstream rotor blades is modeled in a linear cascade. The Reynolds number based on blade chord and exit conditions (5*10^6) and the exit Mach number (1.2) are representative of modern engine operating conditions. The relative motion of shocks and blades is simulated by sending a shock wave along the leading edges of the linear cascade instead of moving the blades through an array of stationary shock waves. The blade geometry is a generic version of a modern high turning rotor blade with transonic exit conditions. The blade is equipped with a showerhead film cooling scheme. Heat flux, surface pressure and surface temperature are measured at six locations on the suction side of the central blade. Pressure measurements are taken with Kulite XCQ-062-50a high frequency pressure transducers. Heat flux data is obtained with Vatell HFM-7/L high speed heat flux sensors. High speed heat flux and pressure data are recorded during the time of the shock impact with and without film cooling. The data is analyzed in detail to find the relative magnitudes of the shock effect on the heat transfer coefficient and the recovery temperature or adiabatic wall temperature (in the presence of film cooling). It is shown that the variations of the heat transfer coefficient and the film effectiveness are less significant than the variations of recovery temperature. The effect of the shock is found to be similar in the cases with and without film cooling. In both cases the variation of recovery temperature induced by the shock is shown to be the main contribution to the overall unsteady heat flux. The unsteady heat flux is compared to results from different prediction models published in the literature. The best agreement of data and prediction is found for a model that assumes a constant heat transfer coefficient and a temperature difference calculated from the unsteady surface pressure assuming an isentropic compression. / Ph. D.

The single-plate interferometer is a powerful flow visualization and aerodynamic measurement tool. It can provide full-field data for the density distribution in a non-intrusive manner, and it can be used for highly unsteady flows. While the device itself represents a large decrease in complexity over other forms of interferometry, the data reduction procedure has traditionally been laborious and difficult. To remove these difficulties and to improve the accuracy of the Virginia Tech interferometer setup, the software has been revamped into a black box design removing the need to handle the code directly. Furthermore, the software has been made to be platform independent by implementing the algorithms using the Java programming language. New hardware has also been added which further simplifies the setup procedure. The improved setup and the new software is used to study the flow around a film cooled turbine blade in the Virginia Tech cascade wind tunnel. The study of this flowfield is used as a validation for the new algorithms and to illustrate the ease of use of the system. Through this analysis, the density distribution for the entire flowfield is acquired. Furthermore the use of Plexiglas as window material was tried. This proved to work, however the manufacturing processing of these windows proved relatively difficult. Studying the film layer close to the surface proved difficult because of inherent limitations with the single-plate interferometer. / Master of Science

In modern, low emission, gas turbine combustion systems the amount of air available for cooling of the flame tube liner is limited. This has led to the development of more complex cooling systems such as cooling tiles i.e. a double skin system, as opposed to the use of more conventional cooling slots i.e. a single skin system. An isothennal experimental facility has been constructed which can incorporate 10 times full size single and double skin (cooling tile) test specimens. The specimens can be tested with or without effusion cooling and measurements have been made to characterise the flow through each cooling system along with the velocity field and cooling effectiveness distributions that subsequently develop along the length of each test section. The velocity field of the coolant film has been defined using pneumatic probes, hot-wire anemometry and PIV instrumentation, whilst gas tracing technique is used to indicate (i) the adiabatic film cooling effectiveness and (ii) mixing of the coolant film with the mainstream flow. Tests have been undertaken both with a datum low turbulence mainstream flow passing over the test section, along with various configurations in which large magnitudes and scales of turbulence were present in the mainstream flow. These high turbulence test cases simulate some of the flow conditions found within a gas turbine combustor. Results are presented relating to a variety of operating conditions for both types of cooling system. The nominal operating condition for the double skin system was at a coolant to mainstream blowing ratio of approximately 1.0. At this condition, mixing of the mainstream and coolant film was relatively small with low mainstream turbulence. However, at high mainstream turbulence levels there was rapid penetration of the mainstream flow into the coolant film. This break up of the coolant film leads to a significant reduction in the cooling effectiveness. In addition to the time-averaged characteristics, the time dependent behaviour of the .:coolantfilm was. also investigated. In particular, unsteadiness associated with large scale structures in the mainstream flow was observed within the coolant film and adjacent to the tile surface. Relative to a double skin system the single skin geometry requires a higher coolant flow rate that, along with other geometrical changes, results in typically higher coolant to mainstream velocity ratios. At low mainstream turbulence levels this difference in velocity between the coolant and mainstream promotes the generation of turbulence and mixing between the streams so leading to some reduction in cooling effectiveness. However, this higher momentum coolant fluid is more resistant to high mainstream turbulence levels and scales so that the coolant film break up is not as significant under these conditions as that observed for the double skin system. For all the configurations tested the use of effusion cooling helped restore the coolant film along the rear of the test section. For the same total coolant flow, the minimum value of cooling effectiveness observed along the test section was increased relative to the no effusion case. In addition the effectiveness of the effusion patch depends on the amount of coolant injected and the axial location of the patch. The overall experimental data suggested the importance of the initial cooling film conditions together with better understanding of the possible mechanisms that results in the rapid cooling film break-up, such as high turbulence mainstream flow and scales, and this will lead to a more effective cooling system design. This experimental data is also thought to be ideal for the validation of numerical predictions.

The turbine blade platform can be protected from hot mainstream gases by injecting cooler air through the gap between stator and rotor. The effectiveness of this film cooling method depends on the geometry of the slot, the quantity of injected air, and the secondary flows near the platform. The purpose of this study was to measure the effect of the upstream vane or stator on this type of platform cooling, as well as the effect of changes in the width of the gap. Film cooling effectiveness distributions were obtained on a turbine blade platform within a linear cascade with upstream slot injection. The width of the slot was varied as well as the mass flow rate of the injected coolant. Obstacles were placed upstream to model the effect of the upstream vane. The coolant was injected through an advanced labyrinth seal to simulate purge flow through a stator-rotor seal. The width of the opening of this seal was varied to simulate the effect of misalignment. Stationary rods were placed upstream of the cascade in four phase locations to model the unsteady wake formed at the trailing edge of the upstream vane. Delta wings were also placed in four positions to create a vortex similar to the passage vortex at the exit of the vane. The film cooling effectiveness distributions were measured using pressure-sensitive paint (PSP). Reducing the width of the slot was found to decrease the area of coolant coverage, although the film cooling effectiveness close to the slot was slightly increased. The unsteady wake was found to have a trivial effect on platform cooling, while the passage vortex from the upstream vane may significantly reduce the film cooling effectiveness.

En vue de leur refroidissement, les parois de chambres de combustion aéronautiques sont perforées de trous à travers lesquels de l’air plus froid est injecté. La paroi est ainsi refroidie par convection et un film isolant est créé en surface chaude (film cooling). Cette thèse a pour objectif d’utiliser les possibilités de la fabrication additive pour proposer de nouvelles solutions architecturées qui permettraient d’augmenter les échanges de chaleur internes et d’obtenir ainsi de meilleures efficacités de refroidissement.La première approche consiste à élaborer de nouveaux designs de plaques multiperforées par Electron Beam Melting (EBM) et Selective Laser Melting (SLM) aux limites de résolution des procédés. Les architectures sont caractérisées en microscopie, en tomographie X et en perméabilité. Des simulations aérothermiques permettent de mettre en évidence l’effet de ces nouveaux designs sur l’écoulement et les échanges de chaleur, et de proposer des voies d’amélioration de la géométrie.La deuxième approche consiste à élaborer de façon simultanée une pièce architecturée par EBM, avec des zones denses et poreuses. A partir d’analyse d’images associée à une cartographie EBSD grand champ, il est possible de remonter aux mécanismes de formation du matériau poreux et de relier la perméabilité et la porosité aux paramètres procédé. Afin de favoriser le film cooling, il pourrait être avantageux que les zones microporeuses soient orientées dans le sens de l’écoulement. Pour ce faire, un nouveau procédé dénommé Magnetic Freezing, où des poudres métalliques forment une structure orientée par un champ magnétique, est mis au point.Les diverses solutions développées durant cette thèse sont testées sur un banc aérothermique. Les essais montrent qu’elles offrent un refroidissement plus efficace et plus homogène que la référence industrielle. Enfin, de premiers tests en combustion sur l’une des structures retenues, plus légère et plus perméable que la référence, montrent qu’il s’agit d’une solution aussi efficace à un débit traversant donné, et donc a priori plus efficace à une surpression donnée. / Combustion chamber walls are perforated with holes so that a cooling air flow can be injected through them. The wall is cooled by convection and an insulating film is created on the hot surface (film cooling). This PhD thesis aims to use the possibilities of additive manufacturing to provide new architectured solutions that could enhance the internal heat exchanges, and lead to a higher cooling effectiveness.The first approach is to develop new designs of multiperforated walls by Electron Beam Melting (EBM) and Selective Laser Melting (SLM) used at the resolution limits of the processes. They are characterized by microscopy, X-ray tomography and permeability tests. Some aerothermal simulations help understanding the effects of these new designs on the flow and on heat exchanges. These results lead to a geometry adaptation.The second approach is to simultaneously manufacture an architectured part with dense and porous zones by EBM. Thanks to image analysis combined with large field EBSD, it is possible to investigate the mechanisms leading to the porous zones and to link them to permeability and porosity. The film cooling effect could be favoured by the orientation of pores towards the cooling flow. Therefore, a new powder-based manufacturing process named Magnetic Freezing, where metallic powders organize into an oriented structure thanks to a magnetic field, is developed.The various solutions studied during this thesis are tested on an aerothermal bench. They all show a more efficient and homogeneous cooling than the industrial reference. Some first tests on one of the selected solutions are performed on a combustion bench. This lighter and more permeable structure proves to be a solution as efficient as the industrial reference at a given flow rate. It should therefore be a more efficient solution for a given overpressure.

This research work investigates the thermal performance of a film-cooled gas turbine endwall under two different mainstream flow conditions. In the first part of the research investigation, the effect of unsteady passing wakes on a film-cooled pitchwise-curved surface (representing an endwall without airfoils) was experimentally studied for heat transfer characteristics on a time-averaged basis. The temperature sensitive paint technique was used to obtain the local temperatures on the test surface. The required heat flux input was provided using foil heaters. Discrete film injection was implemented on the test surface using cylindrical holes with a streamwise inclination angle of 35? and no compound angle relative to the mean approach velocity vector. The passing wakes increased the heat transfer coefficients at both the wake passing frequencies that were experimented. Due to the increasing film cooling jet turbulence and strong jet-mainstream interaction at higher blowing ratios, the heat transfer coefficients were amplified. A combination of film injection and unsteady passing wakes resulted in a maximum pitch-averaged and centerline heat transfer augmentation of ? 28% and 31.7% relative to the no wake and no film injection case. The second part of the research study involves an experimental and numerical analysis of secondary flow and coolant film interaction in a high subsonic annular cascade with a maximum isentropic throat Mach number of ? 0.68. Endwall (platform) thermal protection is provided using discrete cylindrical holes with a streamwise inclination angle of 30? and no compound angle relative to the mean approach velocity vector. The surface flow visualization on the inner endwall provided the location of the saddle point and the three-dimensional separation lines. Computational predictions showed that the leading-edge horseshoe vortex was confined to approximately 1.5% of the airfoil span for the no film injection case and intensified with low momentum film injection. At the highest blowing ratio, the film cooling jet weakened the horseshoe vortex at the leading-edge plane. The passage vortex was intensified with coolant injection at all blowing ratios. It was seen that increasing average blowing ratio improved the film effectiveness on the endwall. The discharge coefficients calculated for each film cooling hole indicated significant non-uniformity in the coolant discharge at lower blowing ratios and the strong dependence of discharge coefficients on the mainstream static pressure and the location of three-dimensional separation lines. Near the airfoil suction side, a region of coalesced film cooling jets providing close to uniform film coverage was observed, indicative of the mainstream acceleration and the influence of three-dimensional separation lines.

The study presented herein describes and analyzes a detailed experimental investigation of the effects of density ratio on endwall thermal performance at varying blowing rates for a typical nozzle guide vane platform purge jet cooling scheme. An axisymmetric converging endwall with an upstream doublet staggered cylindrical hole purge jet cooling scheme was employed. Nominal exit flow conditions were engine representative and as follows: {rm Ma}_{Exit} = 0.85, {rm Re}_{Exit,C_{ax}} = 1.5 times {10}^6, and large-scale freestream Tu = 16%. Two blowing ratios were investigated corresponding to the upper and lower engine extrema. Each blowing ratio was investigated amid two density ratios; one representing typical experimental neglect of density ratio, at DR = 1.2, and another engine representative density ratio achieved by mixing foreign gases, DR = 1.95. All tests were conducted on a linear cascade in the Virginia Tech Transonic Blowdown Wind Tunnel using IR thermography and transient data reduction techniques. Oil paint flow visualization techniques were used to gather quantitative information regarding the alteration of endwall flow physics due two different blowing rates of high-density coolant. High resolution endwall adiabatic film cooling effectiveness, Nusselt number, and Net Heat Flux Reduction contour plots were used to analyze the thermal effects. The effect of density is dependent on the coolant blowing rate and varies greatly from the high to low blowing condition. At the low blowing condition better near-hole film cooling performance and heat transfer reduction is facilitated with increasing density. However, high density coolant at low blowing rates isn't adequately equipped to penetrate and suppress secondary flows, leaving the SS and PS largely exposed to high velocity and temperature mainstream gases. Conversely, it is observed that density ratio only marginally affects the high blowing condition, as the momentum effects become increasingly dominant. Overall it is concluded density ratio has a first order impact on the secondary flow alterations and subsequent heat transfer distributions that occur as a result of coolant injection and should be accounted for in purge jet cooling scheme design and analysis. Additionally, the effect of increasing high density coolant blowing rate was analyzed. Oil paint flow visualization indicated that significant secondary flow suppression occurs as a result of increasing the blowing rate of high-density coolant. Endwall adiabatic film cooling effectiveness, Nusselt number, and NHFR comparisons confirm this. Low blowing rate coolant has a more favorable thermal impact in the upstream region of the passage, especially near injection. The low momentum of the coolant is eventually dominated and entrained by secondary flows, providing less effectiveness near PS, near SS, and into the throat of the passage. The high momentum present for the high blowing rate, high-density coolant suppresses these secondary flows and provides enhanced cooling in the throat and in high secondary flow regions. However, the increased turbulence impartation due to lift off has an adverse effect on the heat load in the upstream region of the passage. It is concluded that only marginal gains near the throat of the passage are observed with an increase in high density coolant blowing rate, but severe thermal penalty is observed near the passage onset. / Master of Science / Gas turbine technology is used frequently in the burning of natural gas for power production. Increases in engine efficiency are observed with increasing firing temperatures, however this leads to the potential of overheating in the stages following. To prevent failure or melting of components, cooler air is extracted from the upstream compressor section and used to cool these components through various highly complex cooling schemes. The design and operational adequacy of these schemes is highly subject to the mainstream and coolant flow conditions, which are hard to represent in a laboratory setting. This experimental study explores the effects of various coolant conditions, and their respective response, for a purge jet cooling scheme commonly found in engine. This scheme utilizes two rows of staggered cylindrical holes to inject air into the mainstream from platform, upstream of the nozzle guide vane. It is the hope that this air forms a protective layer, effectively shielding the platform from the hostile mainstream conditions. Currently, little research has been done to quantify these effects of purge flow cooling scheme while mimicking engine geometry, mainstream and coolant conditions. For this study, an endwall geometry like that found in engine with a purge jet cooling scheme is studied. Commonly, an upstream gap is formed between the combustor lining and first stage vane platform, which is accounted for in this testing. Mainstream and coolant flow conditions can have large impacts on the results gathered, so both were matched to engine conditions. Varying of coolant density and injection rate is studied and quantitative results are gathered. Results indicate coolant fluid density plays a large role in purge jet cooling, and with neglection of this, potential thermal failure points could be overlooked This is exacerbated with less coolant injection. Interestingly, increasing the amount of coolant injected decreases performance across much of the passage, with only marginal gains in regions of complex flow. These results help to better explain the impacts of experimental neglect of coolant density, and aid in the understanding of purge jet coolant injection.