Spelling suggestions: "subject:"finitevolume"" "subject:"finitevolumes""
111 |
Simulace oteplení rozváděčů VN / Simulation of temperature-rise in MV switchgear assembliesKapalla, Alexej January 2021 (has links)
This thesis focuses on the issue of heating of medium-voltage switchgears. The paper contains descriptions of the individual devices which the switchgear consists of. Furthermore, the paper examine the theoretical relations which describe the heating of the conductor. It also present the normative regulations regarding the heading of MV switchgears as well as specific impacts which influence the final temperature-rise. This is followed by chapters that describe the refining of a 3D model of specific switchgear for purposes of simulating temperature-rise, further followed by chapters that look at the actual simulation environment. The thesis further focuses on the actual simulation of MV switchgear temperature-rise and it will compare the results of the simulation with measurements taken under real conditions. The thesis also includes results of simulated temperature-rise while taking into consideration the forced cooling of the switchgear. In the last part, it focuses on the creation of an excel file, which enables the prediction of final results for the temperature-rise of disconnector based on its contact resistance.
|
112 |
Výpočet chlazení transformátoru / Calculation of transformer coolingHetflajš, Martin January 2012 (has links)
This master´s thesis deals with influence of forced air flow from the ventilators on the power transformer cooling. For this analysis was used simulation software ANSYS CFX, that uses the finite volume method for calculations of dynamic properties of liquids. In the introduction of the thesis is presented the basic terminology of fluid flow, temperature fields and theory of transformers. The simulation is divided to the analysis of flow through the left and right radiator models.
|
113 |
Analýza chlazení koncentrátorového fotovoltaického článku / Analysis of the photovoltaic cell coolingHřešil, Tomáš January 2013 (has links)
This project solves the problem of cooling the photovoltaic cell. Solar cell was modeled according to a real model in SolidWorks, and subsequently created the model was simulated in SolidWorks Flow Simulation and Ansys Fluent. The use of both systems allow a comparison of their possibilities in the field of heat transfer and their suitability for the case. The conclusion summarizes the first results and outline further developments cooling design to optimize the performance of the solar cell.
|
114 |
A Finite Volume Approach For Cure Kinetics SimulationMa, Wei 01 January 2012 (has links) (PDF)
In our study, the Finite Volume Method (FVM) is successfully implemented to simulate thermal process of polymerization. This application is verified based on the obtained plots compared with those from other two methods as well as experimental data. After the verification, a method is developed to optimize heat history in order to reduce processing time and in the meantime to maintain the uniformity of cure state. Also sensitivities of cure state to different parameters are examined. Besides, a correlation between temperature and the degree of polymerization profile on sample surface is found using on-line monitoring method.
|
115 |
Implementation of the phase field method with the Immersed Boundary Method for application to wave energy convertersJain, Sahaj Sunil 14 August 2023 (has links)
Consider a bottom-hinged Oscillating Wave Surge Converter (OWSC): This device oscillates due to the hydrodynamic forces applied on it by the action of ocean waves. The focus of this thesis is to build upon the in-house multi-block generalized coordinate finite volume solver GenIDLEST using a collocated grid arrangement within the framework of the fractional-step method to make it compatible to simulate such systems. The first step in this process is to deploy a convection scheme which differentiates between air and water. This process is further complicated by the 1:1000 density and 1:100 viscosity ratio between the two fluids. For this purpose, a phase field method is chosen for its ease of implementation and proven boundedness and conservativeness properties. Extensive validation and verification using standard test cases, such as droplet in shear flow, Rayleigh Taylor instability, and the Dam Break Problem is carried out. This development is then coupled with the present Immersed Boundary Module which is used to simulate the presence of moving bodies and again verified against test cases, such as the Dam Break problem with a vertical obstacle and heave decay of a partially submerged buoyant cylinder. Finally, a relaxation zone technique is used to generate waves and a numerical beach technique is used to absorb them. These are then used to simulate the Oscillating Surge Wave Converter. / Master of Science / An Oscillating Wave Surge Converter can be best described as a rectangular flap, hinged at the bottom, rotating under the influence of ocean waves from which energy is harvested. The singular aim of this thesis is to model this device using Computational Fluid Dynamics (CFD). More specifically, the aim is to model this dynamic device with the full Navier Stokes Equations, which include inertial forces, arising due to the motion of the fluid, viscous forces which dissipate energy, and body forces such as gravity. This involves three key steps:
1. Modelling the air-water interface using a convection scheme. A phase field method is used to differentiate between the two fluids. This task is made more challenging because of the very large density and viscosity differences between air and water.
2. Model dynamic moving geometries in a time-dependent framework. For this, we rely on the Immersed Boundary Method.
3. Develop a numerical apparatus to generate and absorb ocean waves. For this, we rely on the Relaxation Zone and Numerical Beach Method.
These developments are validated in different canonical problems and finally applied to a two-dimensional oscillating surge wave energy converter.
|
116 |
Numerical simulation of paper drying process under infrared radiation emitterBHAGAT, KISHNA NAND 18 April 2008 (has links)
No description available.
|
117 |
Formulation of steady-state and transient potential problems using boundary elementsDruma, Calin January 1999 (has links)
No description available.
|
118 |
Ocean waves in a multi-layer shallow water system with bathymetryParvin, Afroja January 2018 (has links)
Mathematical modeling of ocean waves is based on the formulation and solution of the appropriate equations of continuity, momentum and the choice of proper initial and boundary conditions. Under the influence of gravity, many free surface water waves can be modeled by the shallow water equations (SWE) with the assumption that the horizontal length scale of the wave is much greater than the depth scale and the wave height is much less than the fluid's mean depth. Furthermore, to describe three dimensional flows in the hydrostatic and Boussinesq limits, the multilayer SWE model is used, where the fluid is discretized horizontally into a set of vertical layers, each having its own height, density, horizontal velocity and geopotential. In this study, we used an explicit staggered finite volume method to solve single and multilayer SWE, with and without density stratification and bathymetry, to understand the dynamic of surface waves and internal waves. We implemented a two-dimensional version of the incompressible DYNAMICO method and compare it with a one-dimensional SWE. For multilayer SWE, we considered both two layer and a linear stratification of density, with very small density gradient, consistent with Boussinesq approximation. We used Lagrangian vertical coordinate which doesn't allow mass to flow across vertical layers. Numerical examples are presented to verify multilayer SWE model against single layer SWE, in terms of the phase speed and the steepness criteria of wave profile. In addition, the phase speed of the barotropic and baroclinic mode of two-layer SWE also verified our multilayer SWE model. We found that, for multilayer SWE, waves move slower than single layer SWE and get steeper than normal when they flow across bathymetry. A series of numerical experiment were carried out to compare 1-D shallow water solutions to 2-D solutions with and without density as well as to explain the dynamics of surface wave and internal wave.
We found that, a positive fluctuations on free surface causes water to rise above surface level, gravity pulls it back and the forces that acquired during the falling movement causes the water to penetrate beneath it's equilibrium level, influences the generation of internal waves. Internal waves travel considerably more slowly than surface waves. On the other hand, a bumpy or a slicky formation of surface waves is associated with the propagation of internal waves. The interaction between these two waves is therefore demonstrated and discussed. / Thesis / Master of Science (MSc) / In the modelling of ocean wave, the formulation and solution of appropriate equations and proper initial and boundary conditions are required. The shallow water equations (SWE) are derived from the conservation of mass and momentum equations, in the case where the horizontal length scale of the wave is much greater than the depth scale and the wave height is much less than the fluid's mean depth. In multilayer SWE, the fluid is discretized horizontally into a set of vertical layers, each having its own height, density, horizontal velocity and geopotential. In this study, we used an explicit staggered finite volume method to solve single and multilayer SWE, with and without density stratification and bathymetry, to understand the dynamic of surface waves and internal waves. A series of numerical experiments were carried out to validate our multilayer model. It is found that, in the presence of density differences, surface waves for the multilayer SWE move slowly and get more steep than normal when they flow across bathymetry. Also, a positive fluctuations on free surface generates internal waves at the interior of ocean which propagate along the line of density gradient.
|
119 |
Bilinear Immersed Finite Elements For Interface ProblemsHe, Xiaoming 02 June 2009 (has links)
In this dissertation we discuss bilinear immersed finite elements (IFE) for solving interface problems. The related research works can be categorized into three aspects: (1) the construction of the bilinear immersed finite element spaces; (2) numerical methods based on these IFE spaces for solving interface problems; and (3) the corresponding error analysis. All of these together form a solid foundation for the bilinear IFEs.
The research on immersed finite elements is motivated by many real world applications, in which a simulation domain is often formed by several materials separated from each other by curves or surfaces while a mesh independent of interface instead of a body-fitting mesh is preferred. The bilinear IFE spaces are nonconforming finite element spaces and the mesh can be independent of interface. The error estimates for the interpolation of a Sobolev function in a bilinear IFE space indicate that this space has the usual approximation capability expected from bilinear polynomials, which is <i>O</i>(<i>h</i>²) in <i>L</i>² norm and <i>O</i>(<i>h</i>) in <i>H</i>¹ norm. Then the immersed spaces are applied in Galerkin, finite volume element (FVE) and discontinuous Galerkin (DG) methods for solving interface problems. Numerical examples show that these methods based on the bilinear IFE spaces have the same optimal convergence rates as those based on the standard bilinear finite element for solutions with certain smoothness. For the symmetric selective immersed discontinuous Galerkin method based on bilinear IFE, we have established its optimal convergence rate. For the Galerkin method based on bilinear IFE, we have also established its convergence.
One of the important advantages of the discontinuous Galerkin method is its flexibility for both <i>p</i> and <i>h</i> mesh refinement. Because IFEs can use a mesh independent of interface, such as a structured mesh, the combination of a DG method and IFEs allows a flexible adaptive mesh independent of interface to be used for solving interface problems. That is, a mesh independent of interface can be refined wherever needed, such as around the interface and the singular source. We also develop an efficient selective immersed discontinuous Galerkin method. It uses the sophisticated discontinuous Galerkin formulation only around the locations needed, but uses the simpler Galerkin formulation everywhere else. This selective formulation leads to an algebraic system with far less unknowns than the immersed DG method without scarifying the accuracy; hence it is far more efficient than the conventional discontinuous Galerkin formulations. / Ph. D.
|
120 |
Numerical Simulation of the Fluid-Structure Interaction of a Surface Effect Ship Bow SealBloxom, Andrew Lawrence 22 October 2014 (has links)
Numerical simulations of fluid-structure interaction (FSI) problems were performed in an effort to verify and validate a commercially available FSI tool. This tool uses an iterative partitioned coupling scheme between CD-adapco's STAR-CCM+ finite volume fluid solver and Simulia's Abaqus finite element structural solver to simulate the FSI response of a system. Preliminary verification and validation work (VandV) was carried out to understand the numerical behavior of the codes individually and together as a FSI tool.
Verification and Validation work that was completed included code order verification of the respective fluid and structural solvers with Couette-Pouiselle flow and Euler-Bernoulli beam theory. These results confirmed the 2nd order accuracy of the spatial discretizations used. Following that, a mixture of solution verifications and model calibrations was performed with the inclusion of the physics models implemented in the solution of the FSI problems. Solution verifications were completed for fluid and structural stand-alone models as well as for the coupled FSI solutions. These results re-confirmed the spatial order of accuracy but for more complex flows and physics models as well as the order of accuracy of the temporal discretizations. In lieu of a good material definition, model calibration is performed to reproduce the experimental results. This work used model calibration for both instances of hyperelastic materials which were presented in the literature as validation cases because these materials were defined as linear elastic.
Calibrated, three dimensional models of the bow seal on the University of Michigan bow seal test platform showed the ability to reproduce the experimental results qualitatively through averaging of the forces and seal displacements. These simulations represent the only current 3D results for this case. One significant result of this study is the ability to visualize the flow around the seal and to directly measure the seal resistances at varying cushion pressures, seal immersions, forward speeds, and different seal materials. SES design analysis could greatly benefit from the inclusion of flexible seals in simulations, and this work is a positive step in that direction. In future work, the inclusion of more complex seal geometries and contact will further enhance the capability of this tool. / Ph. D.
|
Page generated in 0.0415 seconds