The demand for power converters is on the rise due to their ability to achieve high power conversion efficiency, small size, light weight and reduced cost. DC-DC converters are used in many applications where, the output voltage needs to be regulated for wide variations in the input voltage and the load. They are also used in applications where electrical isolation is required. Power generation from renewable energy sources suffers from highly fluctuating output voltages. Electrical isolation of renewable energy sources from the grid is essential. Therefore, DC-DC converters are used as an integral part of the power electronic interface required for grid integration of renewable energy sources such as wave energy power conversion. In this dissertation as a first step, the power converters used in wave energy applications are classified and compared. Analysis, design, simulation and experimental results of fixed frequency controlled HF transformer isolated DC-DC resonant converters are presented. The first converter topology presented in Chapter 3 is a ‘fixed frequency controlled single-phase high frequency (HF) transformer isolated DC-DC LCL-type series resonant converter (SRC) with capacitive output filter using a modified gating scheme’. Working of this converter has been explained. Modeling and steady-state analysis of the converter using approximate complex ac circuit analysis method has been done. Various design curves have been obtained. A step-by-step design procedure has been illustrated with an example of a 200 W converter. PSIM simulation results for different operating conditions are presented. Experimental model of the designed converter has been built and the test results are given. Power loss breakdown analysis of the converter has been made. Zero-voltage switching (ZVS) is achieved for different input voltages, and load. This converter cell can be used in interleaved operation to realize higher power converters. The second topology presented in Chapter 4 is ‘a fixed-frequency controlled, 3-phase HF transformer isolated, integrated boost dual 3-phase bridge DC-DC LCL-type SRC with capacitive output filter’. Detailed modeling of the boost section and one of the two identical 3-phase inverter modules is presented. Analysis of the inverter module using approximate complex ac circuit analysis method is presented. Various design curves have been obtained. A step-by-step design procedure has been illustrated with an example of a 600 W converter. Detailed PSIM simulation results for different operating conditions are presented. Experimental model of the designed converter has been built and the test results are given. Power loss breakdown analysis has been made. Major advantage of this converter has been its ability to regulate the output voltage for wide variations in the input voltage and load, while maintaining ZVS for all the switches. Also, due to the parallel connection of the inverter modules the component stresses are significantly reduced. This encourages the converter to be used in high power applications such as wave energy. A 10 kW DC-DC converter cell of the second topology mentioned above has been designed to illustrate the design and working of a high power converter. Performance of the designed converter has been verified by PSIM simulations. This converter operates with ZVS for all the switches for a wide variation in the input voltage and the loading conditions. Power loss breakdown analysis has been performed. / Graduate

There is an increasing demand for power converters with small size, light weight, high conversion efficiency and higher power density. Also, in many applications, there is a need for dc-to-dc converters to accept dc input voltage and provide regulated and/or isolated dc output voltage at a desired voltage level including telecommunications equipment, process control systems, and in industry applications. This thesis presents the analysis, design, simulation and experimental results of three-phase high-frequency transformer isolated resonant converters. The first converter presented is a three-phase LCC-type dc-dc resonant converter with capacitor output filter including the effect of the magnetizing inductance of the three-phase HF transformer. The equivalent ac load resistance is derived and the converter is analyzed by using approximation analysis approach. Base on this analysis, design curves have been obtained and a design example is given. Intusoft simulation results for the designed converter are given for various input voltage and for different load conditions. The experimental verification of the designed converter performance was established by building a 300 W rated power converter and the experimental results have been given. It is shown that the converter works in zero-voltage switching (ZVS) at various input voltage and different load conditions. A three-phase (LC)(L)-type dc-dc series-resonant converter with capacitive output filter has been proposed. Operation of the converter has been presented using the operating waveforms and equivalent circuit diagrams during different intervals. An approximate analysis approach is used to analyze the converter operation, and design procedure is presented with a design example. Intusoft simulation results for the designed converter are given for input voltage and load variations. Experimental results obtained in a 300 W converter are presented. Major advantages of this converter are the leakage and magnetizing inductances of the high-frequency transformer are used as part of resonant circuit and the output rectifier voltage is clamped to the output voltage. The converter operates in soft-switching for the inverter switches for the wide variations in supply voltage and load and it requires narrow switching frequency variation (compared to LCC-type) to regulate the output voltage. A three-phase high-frequency transformer isolated interleaved (LC)(L)-type dc-dc series-resonant converter with capacitive output filter using fixed frequency control is proposed. The converter operation for different modes is presented using the operating waveforms and equivalent circuit diagrams during different intervals. This converter is modeled and then analyzed using the approximate complex ac circuit analysis approach. Based on the analysis, design curves were obtained and the design procedure is presented with a design example. The designed converter is simulated using PSIM software to predict the performance of the converter for variations in supply voltage and load conditions. The converter operates in ZVS for the inverter switches with minimum input voltage and loses ZVS for two switches in each bridge for higher input voltages. / Graduate

Digitally controlled switching DC-DC converters have recently emerged as an attractive alternative to conventional switching converters based on analog control techniques. This research focuses on eliminating the issues associated with the state of the art switching converters by proposing three novel control techniques: (1) a digitally controlled Buck-Boost converter uses a fully synthesized constant ON/OFF time-based fractional-N controller to regulate the output over a 3.3V-to-5.5V input voltage range and provides seamless transition from buck to buck-boost modes (2) a hysteretic buck converter that employs a highly digital hybrid voltage/current mode control to regulate output voltage and switching frequency independently (3) a 10MHz continuous time PID controller using time based signal processing which alleviates the speed limitations associated with conventional analog and digital. All the three techniques employ digitally assisted control techniques and require no external compensation thus making the controllers fully integrated and highly cost effective. / Graduation date: 2013 / Access restricted to the OSU Community at author's request from June 25, 2012 - June 25, 2014