This thesis uses the techniques of atomic force microscope (AFM) and conductive AFM (C-AFM) to study the conduction properties of n-type GaN films. A total of 16 samples were examined and grouped according to their surface morphologies and conduction behaviors. The most common type of surface morpliology was that of Ga-rich samples having undulating "hillocks" with interspersed holes. Although most of the samples had this common morphology, their local conduction behaviors were not all similar. Local I-V spectra of the tip-sample Schottky contact could be grouped according to three major types: low leakage, high leakage, and "p-type". The highest quality samples with low leakage were usually grown at moderate temperatures (~650°C). For such samples, localized leakage only occurred at screw dislocations located at small pits terminating surface hillocks. I-V spectra taken on and off such hillocks were fit in forward bias to determine whether field emission or Frenkel-Poole conduction were dominant. Although field emission is a good fit compared to Frenkel-Poole, yielding reasonable values for the barrier height, the results are not yet conclusive without variable temperature studies.

The electronic structures of Mn £_-doped epitaxial GaN films grown on sapphire substrates are studied by scanning tunneling microscopy in this work. Local structural information and the corresponding electronic properties of Mn £_-doped GaN films are probed by the combination of scanning tunneling microscopy and atomic-scale scanning tunneling spectroscopy measurements. According to the electronic local density of states analysis indicates that Mn ions develop an acceptor level in GaN, revealing a gap state located at ~ 1.4 eV above the valence band edge of GaN. Furthermore, the energy position of the charge transfer levels of substitutional MnGa within GaN energy gap is also elucidated and discussed in the work.

The present work focuses on the growth and characterizations of GaN and InN layers and nanostructures on p-Si(100) and p-Si(111) substrates by plasma-assisted molecular beam epitaxy and the studies of GaN/p-Si and InN/p-Si heterojunctions properties. The thesis is divided in to seven different chapters. Chapter 1 gives a brief introduction on III-nitride materials, growth systems, substrates, possible device applications and technical background. Chapter 2 deals with experimental techniques including the details of PAMBE system used in the present work and characterization tools for III-nitride epitaxial layers as well as nanostructures. Chapter 3 involves the growth of GaN films on p-Si(100) and p-Si(111) substrates. Phase pure wurtzite GaN films are grown on Si (100) substrates by introducing a silicon nitride layer followed by low temperature GaN growth as buffer layers. GaN films grown directly on Si (100) are found to be phase mixtured, containing both cubic and hexagonal modifications. The x-ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) spectroscopy studies reveal that the significant enhancement in the structural and optical properties of GaN films grown with silicon nitride buffer layer grown at 800 oC, when compared to the samples grown in the absence of silicon nitride buffer layer and with silicon nitride buffer layer grown at 600 oC. Core-level photoelectron spectroscopy of SixNy layers reveals the sources for superior qualities of GaN epilayers grown with the high temperature substrate nitridation process. The discussion has been carried out on the typical inverted rectification behavior exhibited by n-GaN/p-Si heterojunctions. Considerable modulation in the transport mechanism is observed with the nitridation conditions. The heterojunction fabricated with the sample of substrate nitridation at high temperature exhibites superior rectifying nature with reduced trap concentrations. Lowest ideality factors (~1.5) are observed in the heterojunctions grown with high temperature substrate nitridation which is attributed to the recombination tunneling at the space charge region transport mechanism at lower voltages and at higher voltages space charge limited current conduction is the dominating transport mechanism. Whereas, thermally generated carrier tunneling and recombination tunneling are the dominating transport mechanisms in the heterojunctions grown without substrate nitridation and low temperature substrate nitridation, respectively. A brief comparison of the structural, optical and heterojunction properties of GaN grown on Si(100) and Si(111) has been carried out. Chapter 4 involves the growth and characterizations of InN nanostructures and thinfilms on p-Si(100) and p-Si(111) substrates. InN QDs are grown on Si(100) at different densities. The PL characteristics of InN QDs are studied. A deterioration process of InN QDs, caused by the oxygen incorporation into the InN lattice and formation of In2O3/InN composite structures was established from the results of TEM, XPS and PL studies. The results confirm the partial oxidation of the outer shell of the InN QDs, while the inner core of the QDs remains unoxidized. InN nanorods are grown on p-Si(100), structural characterizations are carried out by SEM, and TEM. InN nanodots are grown on p-Si(100), structural characterizations are performed. InN films were grown on Si(100) and Si(111) substrates and structural characterizations are carried out. Chapter 5 deals with the the heterojunction properties of InN/p-Si(100) and InN/p-Si(111).The transport behavior of the InN NDs/p-Si(100) diodes is studied at various bias voltages and temperatures. The temperature dependent ZB BH and ideality factors of the forward I-V data are observed, while it is governed through the modified Richardson’s plot. The difference in FB BH and C-V BH and the deviation of ideality factor from unity indicate the presence of inhomogeneities at the interface. The band offsets derived from C-V measurements are found to be Δ EC=1.8 eV and Δ EV =1.3 eV, which are in close agreement with Anderson’s model. The band offsets of InN/p-Si heterojunctions are estimated using XPS data. A type-III band alignment with a valence band offset of Δ EV =1.39 eV and conduction band offset of ΔEC=1.81 eV is identified. The charge neutrality level model provides a reasonable description of the band alignment of the InN/p-Si interface. The interface dipole deduced by comparison with the electron affinity model is 0.06 eV. The transport studies of InN NR/p-Si(100) heterojunctions have been carried out by conductive atomic force microscopy (CAFM) as well as conventional large area contacts. Discussion of the electrical properties has been carried out based on local current-voltage (I-V) curves, as well as on the 2D conductance maps. The comparative studies on transport properties of diodes fabricated with InN NRs and NDs grown on p-Si(100) substrates and InN thin films grown on p-Si(111) substrates have also been carried out. Chapter 6 deals with the growth and characterizations of InN/GaN heterostructures on p-Si(100) and p-Si(111) substarets and also on the InN/GaN/p-Si heterojunction properties. The X-ray diffraction (XRD), scanning electron microscopy (SEM) studies reveal a considerable variation in crystalline quality of InN with grown parameters. Deterioration in the rectifying nature is observed in the case of InN/GaN/p-Si(100) heterojunction substrate when compared to InN/GaN/p-Si (111) due to the defect mediated tunneling effect, caused by the high defect concentration in the GaN and InN films grown on Si(100) and also due to the trap centers exist in the interfaces. Reduction in ideality factor is also observed in the case of n-InN/n-GaN/p–Si(111) when compared to n-InN/n-GaN/p–Si(100) heterojunction. The sum of the ideality factors of individual diodes is consistent with experimentally observed high ideality factors of n-InN/n-GaN/p–Si double heterojunctions due to double rectifying heterojunctions and metal semiconductor junctions. Variation of effective barrier heights and ideality factors with temperature are confirmed, which indicate the inhomogeneity in barrier height, might be due to various types of defects present at the GaN/Si and InN/GaN interfaces. The dependence of forward currents on both the voltage and temperatures are explained by multi step tunneling model and the activation energis were estimated to be 25meV and 100meV for n-InN/n-GaN/p–Si(100) and n-InN/n-GaN/p–Si(111) heterojunctions, respectively. Chapter 7 gives the summary of the present study and also discusses about future research directions in this area.

Group III-A nitrides (GaN, AlN, InN and alloys) are materials of considerable contemporary interest and currently enable a wide variety of optoelectronic and high-power, high-frequency electronic applications. All of these applications utilize device structures that employ a single or multiple hetero-junctions, with material compositions varying across the interface. For example, the workhorse of GaN based electronic devices is the high electron mobility transistor (HEMT) which is usually composed of an AlGaN/GaN hetero-junction, where a two-dimensional electron gas (2DEG) is formed due to differences in polarization between the two layers. In addition to such hetero-junctions in the same material family, formation of hetero-interfaces in nitrides begins right from the epitaxy of the very first layer due to the lack of native substrates for their growth. The consequences of such "dissimilar" hetero-junctions typically manifest as large defect densities at this interface which in turn gives rise to defective films. Additionally, if the substrate is also a semiconductor, the electrical properties at such dissimilar semiconductor-nitride hetero-junctions are particularly important in terms of their influence on the performance of nitride devices. Nevertheless, the large defect densities at such dissimilar 3D-3D semiconductor interfaces, which translate into more trap states, also prevents them from being used as active device layers to say nothing of reliability considerations arising because of these defects. Recently, the advent of 2D materials such as graphene and MoS2 has opened up avenues for Van der Waal’s epitaxy of these layered films with practically any other material. Such defect-free integration enables dissimilar semiconductor hetero-junctions to be used as active device layers with carrier transport across the 2D-3D hetero-interface. This thesis deals with hetero-epitaxial growth platforms for reducing defect densities, and the material and electrical properties of dissimilar hetero-junctions with the group III-A nitride material system.

Group III-nitride semiconductors have received much research attention and witnessed a significant development due to their ample applications in solid-state lighting and high-power/high-frequency electronics. Numerous growth methods were explored to achieve device quality epitaxial III-nitride semiconductors. Among the growth methods for III-nitride semiconductors, molecular beam epitaxy provides advantages such as formation of abrupt interfaces and in-situ monitoring of growth. The present research work focuses on the growth and characterizations of III-nitride based epitaxial films, nanostructures and heterostructures on c-sapphire substrate using plasma-assisted molecular beam epitaxy system. The correlation between structural, optical and electrical properties of III-nitride semiconductors would be extremely useful. The interfaces of the metal/semiconductor and semiconductor heterostructures are very important in the performance of semiconductor devices. In this regard, the electrical transport studies of metal/semiconductor and semiconductor heterostructures have been carried out. Besides, studies involved with the defect induced room temperature ferromagnetism of GaN films and InN nano-structures have also been carried out. The thesis is organized in eight different chapters and a brief overview of each chapter is given below. Chapter 1 provides a brief introduction on physical properties of group III-nitride semiconductors. It also describes the importance of III-nitride heterostructures in the operation of optoelectronic devices. In addition, it also includes the current strategy of the emergence of room temperature ferromagnetism in III-nitride semiconductors. Chapter 2 deals with the basic working principles of molecular beam epitaxy system and different characterization tools employed in the present work. Chapter 3 describes the growth of GaN films on c-sapphire by plasma-assisted molecular beam epitaxy. The effects of N/Ga flux ratio on structural, morphological and optical properties have been studied. The flux ratio plays a major role in controlling crystal quality, morphology and emission properties of GaN films. The dislocation density is found to increase with increase in N/Ga flux ratio. The surface morphologies of the films as seen by scanning electron microscopy show pits on the surface and found that the pit density on the surface increases with flux ratio. The room temperature photoluminescence study reveals the shift in band-edge emission towards the lower energy with increase in N/Ga flux ratio. This is believed to arise from the reduction in compressive stress in the GaN films as it is evidenced by room temperature Raman study. The transport studies on the Pt/GaN Schottky diodes showed a significant increase in leakage current with an increase in N/Ga ratio and is found to be caused by the increase in dislocation density in the GaN films. Chapter 4 deals with the fabrication and characterization of Au/GaN Schottky diodes. The temperature dependent current–voltage measurements have been used to determine the current transport mechanism in Schottky diodes. The barrier height (φb) and the ideality factor (η) are estimated from the thermionic emission model and are found to be temperature dependent in nature, indicating the existence of barrier height inhomogeneities at the Au/GaN interface. The conventional Richardson plot of ln(Is/T2) versus 1/kT gives Richardson constant value of 3.23×10-5 Acm-2 K-2, which is much lower than the known value of 26.4 Acm-2 K-2 for GaN. Such discrepancy of Richardson constant value was attributed to the existence of barrier height inhomogeneities at the Au/GaN interface. The modified Richardson plot of ln(Is/T2)-q2σs2/2k2T2 versus q/kT, by assuming a Gaussian distribution of barrier heights at the Au/GaN interface, provides the Schottky barrier height of 1.47 eV and Richardson constant value of 38.8 Acm-2 K-2 which is very close to the theatrical value of Richardson constant. The temperature dependence of barrier height is interpreted on the basis of existence of the Gaussian distribution of the barrier heights due to the barrier height inhomogeneities at the Au/GaN interface. Chapter 5 addresses on the influence of GaN underlayer thickness on structural, electrical and optical properties of InN thin films grown using plasma-assisted molecular beam epitaxy. The high resolution X-ray diffraction study reveals superior crystalline quality for the InN film grown on thicker GaN film. The electronic and optical properties seem to be greatly influenced by the structural quality of the films, as can be evidenced from Hall measurement and optical absorption spectroscopy. Also, we present the studies involving the dependence of structural, electrical and optical properties of InN films, grown on thicker GaN films, on growth temperature. The optical absorption edge of InN film is found to be strongly dependent on carrier concentration. Kane’s k.p model is used to describe the dependence of optical absorption edge on carrier concentration by considering the non-parabolic dispersion relation for carrier in the conduction band. Chapter 6 deals with the analysis of the temperature dependent current transport mechanisms in InN/GaN heterostructure based Schottky junctions. The barrier height (φb) and the ideality factor (η) of the InN/GaN Schottky junctions are found to be temperature dependent. The temperature dependence of the barrier height indicates that the Schottky barrier height is inhomogeneous in nature at the heterostructure interface. The higher value of the ideality factor and its temperature dependence suggest that the current transport is primarily dominated by thermionic field emission (TFE) other than thermionic emission (TE). The room temperature barrier height and the ideality factor obtained by TFE model are 1.43 eV and 1.21, respectively. Chapter 7 focuses on the defect induced room temperature ferromagnetism in Ga deficient GaN epitaxial films and InN nano-structures grown on c-sapphire substrate by using plasma-assisted molecular beam epitaxy. The observed yellow emission peak in room temperature photoluminescence spectra and the peak positioning at 300 cm-1 in Raman spectra confirms the existence of Ga vacancies in GaN films. The ferromagnetism in Ga deficient GaN films is believed to originate from the polarization of the unpaired 2p electrons of nitrogen surrounding the Ga vacancy. The InN nano-structures of different size are grown on sapphire substrate, the structural and magnetic properties are studied. The room temperature magnetization measurement of InN nano-structures exhibits the ferromagnetic behavior. The saturation magnetization is found to be strongly dependent on the size of the nano-structures. Finally, Chapter 8 gives the summary of the present work and the scope for future work in this area of research.