Comprehensive modeling of gas foil bearings (GFBs) anchored to reliable test data will enable the widespread usage of GFBs into novel turbomachinery applications, such as light weight business aircraft engines, hybrid fuel cell-turbine power systems, and micro-engines recharging battery packs for clean hybrid electric vehicles. Pressurized air is often needed to cool GFBs and to carry away heat conducted from a hot turbine in oil-free micro turbomachinery. Side end pressurization, however, demonstrates a profound effect on the rotordynamic performance of GFBs. This dissertation presents the first study that devotes considerable attention to the effect of side end pressurization on delaying the onset rotor speed of subsynchronous motions. GFB performance depends largely on the support elastic structure, i.e. a smooth foil on top of bump strips. The top foil on bump strips layers is modeled as a two dimensional (2D), finite element (FE) shell supported on axially distributed linear springs. The structural model is coupled to a unique model of the gas film governed by modified Reynolds equation with the evolution of gas flow circumferential velocity, a function of the side end pressure. Predicted direct stiffness and damping increase as the pressure raises, while the difference in cross-coupled stiffnesses, directly related to rotor-bearing system stability, decreases. Prediction also shows that side end pressurization delays the threshold speed of instability. Dynamic response measurements are conducted on a rigid rotor supported on GFBs. Rotor speed-up tests first demonstrate the beneficial effect of side end pressurization on delaying the onset speed of rotor subsynchronous motions. The test data are in agreement with predictions of threshold speed of instability and whirl frequency ratio, thus validating the model of GFBs with side end pressurization. Rotor speed coastdown tests at a low pressure of 0.35 bar evidence nearly uniform normalized rotor motion amplitudes and phase angles with small and moderately large imbalance masses, thus implying a linear rotor response behavior. A finite element rotordynamic model integrates the linearized GFB force coefficients to predict the synchronous responses of the test rotor. A comparison of predictions to test data demonstrates an excellent agreement and successfully validates the rotordynamic model.

Comprehensive modeling of gas foil bearings (GFBs) anchored to reliable test data will enable the widespread usage of GFBs into novel turbomachinery applications, such as light weight business aircraft engines, hybrid fuel cell-turbine power systems, and micro-engines recharging battery packs for clean hybrid electric vehicles. Pressurized air is often needed to cool GFBs and to carry away heat conducted from a hot turbine in oil-free micro turbomachinery. Side end pressurization, however, demonstrates a profound effect on the rotordynamic performance of GFBs. This dissertation presents the first study that devotes considerable attention to the effect of side end pressurization on delaying the onset rotor speed of subsynchronous motions. GFB performance depends largely on the support elastic structure, i.e. a smooth foil on top of bump strips. The top foil on bump strips layers is modeled as a two dimensional (2D), finite element (FE) shell supported on axially distributed linear springs. The structural model is coupled to a unique model of the gas film governed by modified Reynolds equation with the evolution of gas flow circumferential velocity, a function of the side end pressure. Predicted direct stiffness and damping increase as the pressure raises, while the difference in cross-coupled stiffnesses, directly related to rotor-bearing system stability, decreases. Prediction also shows that side end pressurization delays the threshold speed of instability. Dynamic response measurements are conducted on a rigid rotor supported on GFBs. Rotor speed-up tests first demonstrate the beneficial effect of side end pressurization on delaying the onset speed of rotor subsynchronous motions. The test data are in agreement with predictions of threshold speed of instability and whirl frequency ratio, thus validating the model of GFBs with side end pressurization. Rotor speed coastdown tests at a low pressure of 0.35 bar evidence nearly uniform normalized rotor motion amplitudes and phase angles with small and moderately large imbalance masses, thus implying a linear rotor response behavior. A finite element rotordynamic model integrates the linearized GFB force coefficients to predict the synchronous responses of the test rotor. A comparison of predictions to test data demonstrates an excellent agreement and successfully validates the rotordynamic model.

This thesis presents further experimentation and modeling for bump-type gas foil bearings used in oil-free turbomachinery. The effect of shaft temperature on the measured structural force response of foil bearings is of importance for reliable high temperature applications. During actual operation with shaft rotation, the bearing structural parameters are coupled to the effects of a hydrodynamic gas film layer, thus determining the overall bearing load performance. A 38.17 mm inner diameter foil bearing, Generation II, is mounted on an affixed non-rotating hollow shaft with an outer diameter of 38.125 mm. A cartridge heater inserted into the shaft provides a controllable heat source. The clearance between the shaft and the foil bearing increases with increasing shaft temperatures (up to 188°C). A static load (ranging from 0 N to 133 N) is applied to the bearing housing, while measuring the resulting bearing displacement, which represents the compliant structure deflection. Static load versus displacement tests render the bearing static structural stiffness. As the shaft temperature increases, the static test results indicate that the bearing structural stiffness decreases by as much as 70% depending on the bearing orientation. A dynamic load test setup includes a rigid shaft support structure and a suspended electromagnetic shaker. Dynamic load (from 13 N to 31 N) test results show that the test foil bearing stiffness increases by as much as 50% with amplitude of dynamic load above a lightly loaded region, nearly doubles with frequency up to 200 Hz, and decreases by a third as shaft temperature increases. A stick slip phenomenon increases the bearing stiffness at higher frequencies for all the amplitudes of dynamic load tested. The test derived equivalent viscous damping is inversely proportional to amplitude of dynamic load, excitation frequency, and shaft temperature. Further, the estimated bearing dry friction coefficient decreases from 0.52 to 0.36 with amplitude of dynamic load and stays nearly constant as shaft temperature increases. Test results identify static and dynamic bearing parameters for increasing shaft temperature. These experimental results provide a benchmark for predictions from analytical models in current development and are essential to establish sound design practices of the compliant bearing structure.

Gas bearings in oil-free micro-turbomachinery for process gas applications and for power generation (< 400 kW) must offer adequate load capacity and thermal stability, reliable rotordynamic performance at high speeds and temperatures, low power losses and minimal maintenance costs. The metal mesh foil bearing (MMFB) is a promising foil bearing technology offering inexpensive manufacturing cost, large inherent material energy dissipation mechanism, and custom-tailored stiffness and damping properties. This dissertation presents predictions and measurements of the dynamic forced performance of various high speed and high temperature MMFBs. MMFB forced performance depends mainly on its elastic support structure, consisting of arcuate metal mesh pads and a smooth top foil. The analysis models the top foil as a 2D finite element (FE) shell supported uniformly by a metal mesh under-layer. The solution of the structural FE model coupled with a gas film model, governed by the Reynolds equation, delivers the pressure distribution over the top foil and thus the load reaction. A perturbation analysis further renders the dynamic stiffness and damping coefficients for the bearing. The static and dynamic performance predictions are validated against limited published experimental data. A one-to-one comparison of the static and dynamic forced performance characteristics of a MMFB against a Generation I bump foil bearing (BFB) of similar size, with a slenderness ratio L/D=1.04, showcases the comparative performance of MMFB against a commercially available gas foil bearing design. The measurements of rotor lift-off speed and drag friction at start-up and airborne conditions are conducted for rotor speeds up to 70 krpm and under identical specific loads (W/LD =0.06 to 0.26 bar). The dynamic force coefficients of the bearings are estimated, in a ‘floating bearing’ type test rig, while floating atop a journal spinning to speeds as high as 50 krpm and with controlled static loads (22 N) applied in the vertical direction. The parameter identification is conducted in the frequency range of 200-400 Hz first, and then up to 600 Hz using higher load capacity shakers. A finite element rotordynamic program (XLTRC2) models a hollow rotor and two MMFBs supporting it and predict the synchronous rotor response for known imbalances. The predictions agree well with the ambient temperature rotor response measurements. Extensive rotor response measurements and rotor and bearing temperature measurements, with a coil heater warming up to 200 ºC and placed inside the hollow rotor, reveal the importance of adequate thermal management. The database of high speed high temperature performance measurements and the development of a predictive tool will aid in the design and deployment of MMFBs in commercial high-speed turbomachinery. The work presented in the dissertation is a cornerstone for future analytical developments and further testing of practical MMFBs.