Thesis (M.S.)--West Virginia University, 2003. / Title from document title page. Document formatted into pages; contains xvii, 103 p. : ill. (some col.), maps. Includes abstract. Includes bibliographical references (p. 52-55).

Large volumes of natural gas exist in tight fissured reservoirs. Hydraulic fracturing is one of the main stimulating techniques to enhance recovery from these fractured reservoirs. Although hydraulic fracturing has been used for decades for the stimulation of tight gas reservoirs, a thorough understanding of the interaction between induced hydraulic fractures and natural fractures is still lacking. Recent examples of hydraulic fracture diagnostic data suggest complex, multi-stranded hydraulic fracture geometry is a common occurrence. The interaction between pre-existing natural fractures and the advancing hydraulic fracture is a key condition leading to complex fracture patterns. Large populations of natural fractures that exist in formations such as the Barnett shale are sealed by precipitated cements which could be quartz, calcite, etc. Even though there is no porosity in the sealed fractures, they may still serve as weak paths for fracture initiation and/or for diverting the path of the growing hydraulic fractures. Performing hydraulic fracture design calculations under these complex conditions requires modeling of fracture intersections and tracking fluid fronts in the network of reactivated fissures. In this dissertation, the effect of the cohesiveness of the sealed natural fractures and the intact rock toughness in hydraulic fracturing are studied. Accordingly, the role of the pre-existing fracture geometry is also investigated. The results provide some explanations for significant differences in hydraulic fracturing in naturally fractured reservoirs from non-fractured reservoirs. For the purpose of this research, an extended finite element method (XFEM) code is developed to simulate fracture propagation, initiation and intersection. The motivation behind applying XFEM are the desire to avoid remeshing in each step of the fracture propagation, being able to consider arbitrary varying geometry of natural fractures and the insensitivity of fracture propagation to mesh geometry. New modifications are introduced into XFEM to improve stress intensity factor calculations, including fracture intersection criteria into the model and improving accuracy of the solution in near crack tip regions. The presented coupled fluid flow-fracture mechanics simulations extend available modeling efforts and provide a unified framework for evaluating fracture design parameters and their consequences. Results demonstrate that fracture pattern complexity is strongly controlled by the magnitude of in situ stress anisotropy, the rock toughness, the natural fracture cement strength, and the approach angle of the hydraulic fracture to the natural fracture. Previous studies (mostly based on frictional fault stability analysis) have concentrated on predicting the onset of natural fracture failure. However, the use of fracture mechanics and XFEM makes it possible to evaluate the progression of fracture growth over time as fluid is diverted into the natural fractures. Analysis shows that the growing hydraulic fracture may exert enough tensile and/or shear stresses on cemented natural fractures that they may be opened or slip in advance of hydraulic fracture tip arrival, while under some conditions, natural fractures will be unaffected by the hydraulic fracture. A threshold is defined for the fracture energy of cements where, for cases below this threshold, hydraulic fractures divert into the natural fractures. The value of this threshold is calculated for different fracture set orientations. Finally, detailed pressure profile and aperture distributions at the intersection between fracture segments show the potential for difficulty in proppant transport under complex fracture propagation conditions. Whether a hydraulic fracture crosses or is arrested by a pre-existing natural fracture is controlled by shear strength and potential slippage at the fracture intersections, as well as potential debonding of sealed cracks in the near-tip region of a propagating hydraulic fracture. We introduce a new more general criterion for fracture propagation at the intersections. We present a complex hydraulic fracture pattern propagation model based on the Extended Finite Element Method as a design tool that can be used to optimize treatment parameters under complex propagation conditions. / text

Not available / text

This project is a research into the effect of gas condensate damage in hydraulically fractured wells. It is the result of a problem encountered in producing a low permeability formation from a well in South Texas owned by the El Paso Production Company. The well was producing a gas condensate reservoir and questions were raised about how much drop in flowing bottomhole pressure below dewpoint would be appropriate. Condensate damage in the hydraulic fracture was expected to be of significant effect. Previous attempts to answer these questions have been from the perspective of a radial model. Condensate builds up in the reservoir as the reservoir pressure drops below the dewpoint pressure. As a result, the gas moving to the wellbore becomes leaner. With respect to the study by El-Banbi and McCain, the gas production rate may stabilize, or possibly increase, after the period of initial decline. This is controlled primarily by the condensate saturation near the wellbore. This current work has a totally different approach. The effects of reservoir depletion are minimized by introduction of an injector well with fluid composition the same as the original reservoir fluid. It also assumes an infinite conductivity hydraulic fracture and uses a linear model. During the research, gas condensate simulations were performed using a commercial simulator (CMG). The results of this research are a step forward in helping to improve the management of gas condensate reservoirs by understanding the mechanics of liquid build-up. It also provides methodology for quantifying the condensate damage that impairs linear flow of gas into the hydraulic fracture.

Thesis (M.S.)--West Virginia University, 2008. / Title from document title page. Document formatted into pages; contains vii, 104 p. : ill. (some col.), maps (some col.). Includes abstract. Includes bibliographical references (p. 100-104).

Thesis (M.S.)--West Virginia University, 2004. / Title from document title page. Document formatted into pages; contains viii, 86 p. : ill. (some col.), map. Includes abstract. Includes bibliographical references (p. 66-68).

Thesis (M.S.)--West Virginia University, 2009. / Title from document title page. Document formatted into pages; contains vii, 40 p. : col. ill. Includes abstract. Includes bibliographical references (p. 39-40).

Thesis (Ph. D.)--University of Texas at Austin, 2009. / Title from PDF title page (University of Texas Digital Repository, viewed on Sept. 10, 2009). Vita. Includes bibliographical references.

Fracture patterns control flow and transport properties in a tight gas reservoir and therefore play a great role in siting the production wells. Hence, it is very important that the exact location and orientation of fractures or fracture swarms is known. Numerical models show that the fractures may be manifested on seismograms as discrete events.A number of data processing workflows were designed and examined to enhance these fracture signals and to suppress the reflections in seismic data. The workflows were first tested on a 2D synthetic data set, and then applied to 3D field data from the San Juan Basin in New Mexico. All these workflows combine conventional processing tools which makes them easily applicable. Use of conventional P-wave data may also make this approach to locate fractures more economical than other currently available technology which often requires S-wave survey or computationally intensive inversion of data. Diode filtering and dip-filtering in the common-offset domain yield good results and work very well in the presence of flat reflectors. NMO-Dip filter depends on the NMO velocity of the subsurface, but removes both flat and slightly dipping reflectors without affecting the fracture signals. Prior application of dip-moveout correction (DMO) did not make any difference on reflections, but included some incoherent noise to the data. The Eigenvector filter performed very well on flat or near-flat reflectors and left the fracture signals almost intact, but introduced some incoherent noise in the presence of steeply dipping reflectors. Harlan's scheme and Radon filtering are very sensitive with regard to parameters selection, but perform exceptionally well on flat or near-flat reflectors. Dip-filter, Eigenvector filter, and Radon filter were also tested on 3D land data. Dip-filter and Eigenvector filter suppressed strong reflections with slight perturbations to the fracture signals. Radon filter did not produce satisfactory result due to small residual moveout difference between reflectors and fracture signals. / Master of Science

Petroleum and Geosystems Engineering / Production from unconventional reservoirs became popular in the last decade in the U.S. Promising production results and predictions, as well as improvements in hydraulic fracturing and horizontal drilling technology made unconventional reservoirs economically feasible. Therefore, an effective and efficient reservoir model for unconventional resources became a must. In order to model production from such resources, analytical, semi-analytical, and numerical models have been developed, but analytical models are frequently used due to their practicality, relative simplicity, and also due to limited availability of field data. This research project has been accomplished in two main parts. In the first part, two analytical models for unconventional reservoirs, one with infinite hydraulic fracture conductivity assumption proposed by Patzek et al. (2013), while the other one with finite hydraulic fracture conductivity assumption developed by Ozkan et al. (2011) are compared. Additionally, a commercial reservoir simulator (CMG, IMEX, 2012) is employed to compare the results with the analytical models. Sensitivity study is then performed to identify the critical parameters controlling the production performance of unconventional reservoirs. In the second part, naturally and hydraulically fractured unconventional reservoir is considered. In addition, geomechanical effects on natural and hydraulic fractures are examined. A simple analytical dual porosity model, which represents the natural fractures in unconventional reservoirs, is improved to handle the constant bottom-hole pressure production scenario to identify the production performance differences between the cases with and without geomechanical effects. Finally, geomechanical effects are considered for combined natural and hydraulic fractures, and an evaluation of the circumstances in which the geomechanical effects cause a significant production loss is carried out. / text