Spelling suggestions: "subject:"sas burbine combustor"" "subject:"sas burbine combustors""
1 |
EMISSIONS, COMBUSTION DYNAMICS, AND CONTROL OF A MULTIPLE SWIRL COMBUSTORLI, GUOQIANG 06 October 2004 (has links)
No description available.
|
2 |
Experimental Investigation of Flow and Wall Heat Transfer in an Optical Combustor for Reacting Swirl FlowsPark, Suhyeon 23 February 2018 (has links)
The study of flow fields and heat transfer characteristics inside a gas turbine combustor provides one of the most serious challenges for gas turbine researchers because of the harsh environment at high temperatures. Design improvements of gas turbine combustors for higher efficiency, reduced pollutant emissions, safety and durability require better understanding of combustion in swirl flows and thermal energy transfer from the turbulent reacting flows to solid surfaces. Therefore, accurate measurement and prediction of the flows and heat loads are indispensable.
This dissertation presents flow details and wall heat flux measurements for reacting flow conditions in a model gas turbine combustor. The objective is to experimentally investigate the effects of combustor operating conditions on the reacting swirl flows and heat transfer on the liner wall. The results shows the behavior of swirling flows inside a combustor generated by an industrial lean pre-mixed, axial swirl fuel nozzle and associated heat loads.
Planar particle image velocimetry (PIV) data were analyzed to understand the characteristics of the flow field. Experiments were conducted with various air flow rates, equivalence ratios, pilot fuel split ratios, and inlet air temperatures. Methane and propane were used as fuel. Characterizing the impingement location on the liner, and the turbulent kinetic energy (TKE) distribution were a main part of the investigation. Proper orthogonal decomposition (POD) further analyzed the data to compare coherent structures in the reacting and non-reacting flows. Comparison between reacting and non-reacting flows yielded very striking differences. Self-similarity of the flow were observed at different operating conditions.
Flow temperature measurements with a thermocouple scanning probe setup revealed the temperature distribution and flow structure. Features of premixed swirl flame were observed in the measurement. Non-uniformity of flow temperature near liner wall was observed ranging from 1000 K to 1400 K. The results provide insights on the driving mechanism of convection heat transfer.
As a novel non-intrusive measurement technique for reacting flows, flame infrared radiation was measured with a thermographic camera. Features of the flame and swirl flow were observed from reconstructed map of measured IR radiation projection using Abel transformation. Flow structures in the infrared measurement agreed with observations of flame luminosity images and the temperature map. The effect of equivalence ratio on the IR radiation was observed.
Liner wall temperature and heat transfer were measured with infrared thermographic camera. The combustor was operated under reacting condition to test realistic heat load inside the industrial combustors. Using quartz glass liner and KG2 filter glass, the IR camera could measure inner wall surface temperature through the glass at high temperature. Time resolved axial distributions of inner/outer wall temperature were obtained, and hot side heat flux distribution was also calculated from time accurate solution of finite difference method.
The information about flows and wall heat transfer found in this work are beneficial for numerical simulations for optimized combustor cooling design. Measurement data of flow temperature, velocity field, infrared radiation, and heat transfer can be used as validation purpose or for direct inputs as boundary conditions. Time-independent location of peak location of liner wall temperature was found from time resolved wall temperature measurements and PIV flow measurements. This indicates the location where the cooling design should be able to compensate for the temperature increase in lean premixed swirl combustors.
The characteristics on the swirl flows found in this study points out that the reacting changes the flow structure significantly, while the operating conditions has minor effect on the structure. The limitation of non-reacting testing must be well considered for experimental combustor studies. However, reacting testing can be performed cost-effectively for reduced number of conditions, utilizing self-similar characteristics of the flows found in this study. / Ph. D.
|
3 |
Heat Transfer and Flow Measurements in an Atmospheric Lean Pre-Mixed CombustorGomez Ramirez, David 19 July 2016 (has links)
Energy conservation, efficiency, and environmental responsibility are priorities for modern energy technologies. The ever increasing demands for lower pollutants and higher performance have driven the development of low-emission gas turbine engines, operating at lean equivalence ratios and at increasingly higher turbine inlet temperatures. This has placed new constraints on gas turbine combustor design, particularly in regards to the cooling technologies available for the combustor liner walls. To optimize combustor thermal management, and in turn optimize overall engine performance, detailed measurements of the flame side heat transfer are required. However, given the challenging environment at which gas turbine combustors operate, there are currently only limited studies that quantify flame side combustor heat transfer; in particular at reacting conditions.
The objective of the present work was to develop methodologies to measure heat transfer within a reacting gas turbine combustor. To accomplish this, an optically accessible research combustor system was designed and constructed at Virginia Tech, capable of operating at 650 K inlet temperature, maximum air mass flow rates of 1.3 kg/s, and flame temperatures over 1800 K. Flow and heat transfer measurements at non-reacting and reacting conditions were carried out for Reynolds numbers (Re) with respect to the combustor diameter ranging from ~11 500 to ~140 000 (depending on the condition). Particle Image Velocimetry (PIV) was used to measure the non-reacting flow field within the burner, leading to the identification of coherent structures in the flow that accounted for over 30% of the flow fluctuation kinetic energy along the swirling jet shear layers. The capability of infrared (IR) thermography to image surface temperatures through a fused silica (quartz) glass was demonstrated at non-reacting conditions. IR thermography was then used to measure the non-reacting steady state heat transfer along the combustor liner. A peak in heat transfer was identified at ~1 nozzle diameter downstream of the combustor dome plate. The peak Nusselt number along the liner was over 18 times higher than that predicted from fully developed turbulent pipe flow correlations, which have traditionally been used to estimate flame side combustor heat transfer.
For the reacting measurements, a novel time-dependent heat transfer methodology was developed that allowed for the investigation of transient heat loads, including those occurring during engine ignition and shutdown. The methodology was validated at non-reacting conditions, by comparing results from an experiment with changing flow temperature, to the results obtained at steady state. The difference between the time-dependent and the steady state measurements were between 3% and 17.3% for different mass flow conditions. The time-dependent methodology was applied to reacting conditions for combustor Reynolds numbers of ~12 000 and ~24 000. At an equivalence ratio of ~0.5 and a combustor Reynolds number of ~12 000, the peak heat load location in reaction was shifted downstream by 0.2 nozzle diameters compared to the non-reacting cases. At higher equivalence ratios, and more visibly at a Reynolds number of ~24 000, the heat transfer distribution along the combustor liner exhibited two peaks, upstream and downstream of the impingement location (X/DN=0.8-1.0 and X/DN=2.5). Reacting PIV was performed at Re=12 000 showing the presence of a strong corner recirculation, which could potentially convect reactants upstream of the impingement point, leading to the double peak structure observed.
The methodologies developed have provided insight into heat transfer within gas turbine combustors. The methods can be used to explore additional conditions and expand the dataset beyond what is presented, to fully characterize reacting combustor heat transfer. / Ph. D.
|
4 |
Development of gas turbine combustor preliminary design methodologies and preliminary assessments of advanced low emission combustor conceptsKhandelwal, Bhupendra January 2012 (has links)
It is widely accepted that climate change is a very serious environmental concern. Levels of carbon dioxide (CO2) and other emissions in the global atmosphere have increased substantially since the industrial revolution and now increasing faster than ever before. There is a thought that this has already led to dangerous warming in the Earth’s atmosphere and relevant changes around. Emissions legislations are going to be stringent as the years will pass. Hydro carbon fuel cost is also increasing substantially; more over this is non- renewable source of energy. There is an urgent need for novel combustor technologies for reducing emission as well as exploring alternative renewable fuels without effecting combustor performance. Development of novel combustors needs comprehensive understanding of conventional combustors. The design and development of gas turbine combustors is a crucial but uncertain part of an engine development process. At present, the design process relies upon a wealth of experimental data and correlations. Some major engine manufacturers have addressed the above problem by developing computer programs based on tests and empirical data to assist combustor designers, but such programs are proprietary. There is a need of developing design methodologies for combustors which would lead to substantial contribution to knowledge in field of combustors. Developed design methodologies would be useful for researchers for preliminary design assessments of a gas turbine combustor. In this study, step by step design methodologies of dual annular radial and axial combustor, triple annular combustor and reverse flow combustor have been developed. Design methodologies developed could be used to carry out preliminary design along with performance analysis for conventional combustion chambers. In this study the author has also proposed and undertaken preliminary studies of some novel combustor concepts. A novel concept of a dilution zone less combustor has been proposed in this study. According to this concept dilution air would be introduced through nozzle guide vanes to provide an optimum temperature traverse for turbine blades. Preliminary study on novel dilution zone less combustor predicts that the length of this combustor would be shorter compared to conventional case, resulting in reduced weight, fuel burn and vibrations. Reduced fuel burn eventually leads to lower emissions. Another novel concept of combustor with hydrogen synthesis from kerosene reformation has been proposed and a preliminary studies has been undertaken in this work. Addition of hydrogen as an additive in gas turbine combustor shows large benefits to the performance of gas turbine engines in addition to reduction in NOx levels. The novel combustor would have two stages, combustion of ~5% of the hydrocarbon fuel would occur in the first stage at higher equivalence ratios in the presence of a catalyst, which would eventually lead to the formation of hydrogen rich flue gases. In the subsequent stage the hydrogen rich flue gases from the first stage would act as an additive to combustion of the hydrocarbon fuel. It has been preliminary estimated that the mixture of the hydrocarbon fuel and air could subsequently be burned at much lower equivalence ratios than conventional cases, giving better temperature profiles, flame stability limits and lower NOx emissions. The effect of different geometrical parameters on the performance of vortex controlled hybrid diffuser has also been studied. It has been predicted that vortex chamber in vortex controlled hybrid diffuser does not play any role in altering the performance of diffuser. The overall contribution to knowledge of this study is development of combustor preliminary design methodologies with different variants. The other contribution to knowledge is related to novel combustors with a capability to produce low emissions. Study on novel combustor and diffuser has yielded application of two patent applications with several other publications which has resulted in a contribution to knowledge. A list of research articles, two patents, awards and achievements are presented in Appendix C.
|
5 |
Impingement Cooling: Heat Transfer Measurement by Liquid Crystal ThermographyOmer, Muhammad January 2010 (has links)
<p>In modern gas turbines parts of combustion chamber and turbine section are under heavy heat load, for example, the rotor inlet temperature is far higher than the melting point of the rotor blade material. These high temperatures causes thermal stresses in the material, therefore it is very important to cool the components for safe operation and to achieve desired component life. But on the other hand the cooling reduces the turbine efficiency, for that reason it is vital to understand and optimize the cooling technique.</p><p>In this project Thermochromic Liquid Crystals (TLCs) are used to measure distribution of heat transfer coefficient over a scaled up combustor liner section. TLCs change their color with the variation of temperature in a particular temperature range. The color-temperature change relation of a TLC is sharp and precise; therefore TLCs are used to measure surface temperature by painting the TLC over a test surface. This method is called Liquid Crystal Thermography (LCT). LCT is getting popular in industry due to its high-resolution results, repeatability and ease of use.</p><p>Test model in present study consists of two plates, target plate and impingement plate. Cooling of the target plate is achieved by impingement of air coming through holes in the impingement plate. The downstream surface of the impingement plate is then cooled by cross flow and re-impingement of the coolant air.</p><p>Heat transfer on the target plate is not uniform; areas under the jet which are called stagnation points have high heat transfer as compare to the areas away from the center of jet. It is almost the same situation for the impingement plate but the location of stagnation point is different. A transient technique is used to measure this non-uniform heat transfer distribution. It is assumed that the plates are semi-infinitely thick and there is no lateral heat transfer in the plates. To fulfill the assumptions a calculated time limit is followed and the test plates are made of Plexiglas which has very low thermal conductivity.</p><p>The transient technique requires a step-change in the mainstream temperature of the test section. However, in practical a delayed increase in mainstream temperature is attained. This issue is dealt by applying Duhamel’s theorem on the step-change heat transfer equation. MATLAB is used to get the Hue data of the recorded video frames and calculate the time taken for each pixel to reach a predefined surface temperature. Having all temperatures and time values the heat transfer equation is iteratively solved to get the value of heat transfer coefficient of each and every pixel of the test surface.</p><p>In total fifteen tests are conducted with different Reynolds number and different jet-to-target plate distances. It is concluded that for both the target and impingement plates, a high Reynolds number provides better overall heat transfer and increase in jet-to-target distance</p><p>decreases the overall heat transfer.</p>
|
6 |
Impingement Cooling: Heat Transfer Measurement by Liquid Crystal ThermographyOmer, Muhammad January 2010 (has links)
In modern gas turbines parts of combustion chamber and turbine section are under heavy heat load, for example, the rotor inlet temperature is far higher than the melting point of the rotor blade material. These high temperatures causes thermal stresses in the material, therefore it is very important to cool the components for safe operation and to achieve desired component life. But on the other hand the cooling reduces the turbine efficiency, for that reason it is vital to understand and optimize the cooling technique. In this project Thermochromic Liquid Crystals (TLCs) are used to measure distribution of heat transfer coefficient over a scaled up combustor liner section. TLCs change their color with the variation of temperature in a particular temperature range. The color-temperature change relation of a TLC is sharp and precise; therefore TLCs are used to measure surface temperature by painting the TLC over a test surface. This method is called Liquid Crystal Thermography (LCT). LCT is getting popular in industry due to its high-resolution results, repeatability and ease of use. Test model in present study consists of two plates, target plate and impingement plate. Cooling of the target plate is achieved by impingement of air coming through holes in the impingement plate. The downstream surface of the impingement plate is then cooled by cross flow and re-impingement of the coolant air. Heat transfer on the target plate is not uniform; areas under the jet which are called stagnation points have high heat transfer as compare to the areas away from the center of jet. It is almost the same situation for the impingement plate but the location of stagnation point is different. A transient technique is used to measure this non-uniform heat transfer distribution. It is assumed that the plates are semi-infinitely thick and there is no lateral heat transfer in the plates. To fulfill the assumptions a calculated time limit is followed and the test plates are made of Plexiglas which has very low thermal conductivity. The transient technique requires a step-change in the mainstream temperature of the test section. However, in practical a delayed increase in mainstream temperature is attained. This issue is dealt by applying Duhamel’s theorem on the step-change heat transfer equation. MATLAB is used to get the Hue data of the recorded video frames and calculate the time taken for each pixel to reach a predefined surface temperature. Having all temperatures and time values the heat transfer equation is iteratively solved to get the value of heat transfer coefficient of each and every pixel of the test surface. In total fifteen tests are conducted with different Reynolds number and different jet-to-target plate distances. It is concluded that for both the target and impingement plates, a high Reynolds number provides better overall heat transfer and increase in jet-to-target distance decreases the overall heat transfer.
|
7 |
Development of gas turbine combustor preliminary design methodologies and preliminary assessments of advanced low emission combustor conceptsKhandelwal, Bhupendra 07 1900 (has links)
It is widely accepted that climate change is a very serious environmental
concern. Levels of carbon dioxide (CO2) and other emissions in the global
atmosphere have increased substantially since the industrial revolution and now
increasing faster than ever before. There is a thought that this has already led
to dangerous warming in the Earth’s atmosphere and relevant changes around.
Emissions legislations are going to be stringent as the years will pass. Hydro
carbon fuel cost is also increasing substantially; more over this is non-
renewable source of energy.
There is an urgent need for novel combustor technologies for reducing emission
as well as exploring alternative renewable fuels without effecting combustor
performance. Development of novel combustors needs comprehensive
understanding of conventional combustors. The design and development of gas
turbine combustors is a crucial but uncertain part of an engine development
process. At present, the design process relies upon a wealth of experimental
data and correlations. Some major engine manufacturers have addressed the
above problem by developing computer programs based on tests and empirical
data to assist combustor designers, but such programs are proprietary. There is
a need of developing design methodologies for combustors which would lead to
substantial contribution to knowledge in field of combustors. Developed design
methodologies would be useful for researchers for preliminary design
assessments of a gas turbine combustor.
In this study, step by step design methodologies of dual annular radial and axial
combustor, triple annular combustor and reverse flow combustor have been
developed. Design methodologies developed could be used to carry out
preliminary design along with performance analysis for conventional combustion
chambers. In this study the author has also proposed and undertaken
preliminary studies of some novel combustor concepts.
A novel concept of a dilution zone less combustor has been proposed in this
study. According to this concept dilution air would be introduced through nozzle
guide vanes to provide an optimum temperature traverse for turbine blades.
Preliminary study on novel dilution zone less combustor predicts that the length
of this combustor would be shorter compared to conventional case, resulting in
reduced weight, fuel burn and vibrations. Reduced fuel burn eventually leads to
lower emissions.
Another novel concept of combustor with hydrogen synthesis from kerosene
reformation has been proposed and a preliminary studies has been undertaken
in this work. Addition of hydrogen as an additive in gas turbine combustor
shows large benefits to the performance of gas turbine engines in addition to
reduction in NOx levels. The novel combustor would have two stages,
combustion of ~5% of the hydrocarbon fuel would occur in the first stage at
higher equivalence ratios in the presence of a catalyst, which would eventually
lead to the formation of hydrogen rich flue gases. In the subsequent stage the
hydrogen rich flue gases from the first stage would act as an additive to
combustion of the hydrocarbon fuel. It has been preliminary estimated that the
mixture of the hydrocarbon fuel and air could subsequently be burned at much
lower equivalence ratios than conventional cases, giving better temperature
profiles, flame stability limits and lower NOx emissions.
The effect of different geometrical parameters on the performance of vortex
controlled hybrid diffuser has also been studied. It has been predicted that
vortex chamber in vortex controlled hybrid diffuser does not play any role in
altering the performance of diffuser.
The overall contribution to knowledge of this study is development of combustor
preliminary design methodologies with different variants. The other contribution
to knowledge is related to novel combustors with a capability to produce low
emissions. Study on novel combustor and diffuser has yielded application of two
patent applications with several other publications which has resulted in a
contribution to knowledge. A list of research articles, two patents, awards and
achievements are presented in Appendix C.
|
8 |
Density-based unstructured simulations of gas-turbine combustor flowsAlmutlaq, Ahmed N. January 2007 (has links)
The goal of the present work was to identify and implement modifications to a density-based unstructured RANS CFD algorithm, as typically used in turbomachinery flows (represented here via the RoIIs-Royce 'Hydra' code), for application to Iow Mach number gas-turbine combustor flows. The basic algorithm was modified to make it suitable for combustor relevant problems. Fixed velocity and centreline boundary conditions were added using a characteristic based method. Conserved scalar mean and variance transport equations were introduced to predict scalar mixing in reacting flows. Finally, a flarnelet thermochemistry model for turbulent non-premixed combustion with an assumed shape pdf for turbulence-chemistry interaction was incorporated. A method was identified whereby the temperature/ density provided by the combustion model was coupled directly back into the momentum equations rather than from the energy equation. Three different test cases were used to validate the numerical capabilities of the modified code, for isothermal and reacting flows on different grid types. The first case was the jet in confined cross flow associated with combustor liner-dilution jetcore flow interaction. The second was the swirling flow through a multi-stream swirler. These cases represent the main aerodynamic features of combustor primary zones. The third case was a methane-fueled coaxial jet combustor to assess the combustion model implementation. This study revealed that, via appropriate modifications, an unstructured density-based approach can be utilised to simulate combustor flows. It also demonstrated that unstructured meshes employing nonhexahedral elements were inefficient at accurate capture of flow processes in regions combining rapid mixing and strong convection at angles to cell edges. The final version of the algorithm demonstrated that low Mach RANS reacting flow simulations, commonly performed using a pressure-based approach, can successfully be reproduced using a density-based approach.
|
9 |
The experimental flowfield and thermal measurements in an experimental can-type gas turbine combustorMeyers, Bronwyn Clara 25 August 2010 (has links)
In this study, experimental data was collected in order to create a test case that can be used to validate computational fluid dynamics (CFD) simulations and the individual models used therein for gas turbine combustor applications. In many cases, the CFD results of gas turbine combustors do not correlate well with experimental results. For this reason, there is a requirement to test the simulation method used before CFD can successfully be used for combustor design. This test case encompasses all the features of a gas turbine combustor such as a swirler, primary, secondary and dilution holes as well as cooling rings. Experiments were performed on the same combustor geometry for both non-reacting and reacting flows. The non-reacting flow experiments consisted of stereoscopic particle image velocimetry (PIV) measurements performed at various planes in the three zones of the combustor. Data was collected on planes, both in line with the holes and in between the holes of each zone. For the reacting experiments, the temperatures on the outlet plane were measured using a thermocouple rake, thus a temperature contour plot on the outlet plane was produced. Further, the combustor can was modified with passive inserts, which were tested to determine their influence on the outlet temperature distribution during reacting runs. In this set-up, the outlet velocity profiles were also measured using a Pitot tube during both non-reacting and reacting flows. In addition to the outlet temperature distribution and velocity profiles, images of the flame patterns were captured, which showed the positions of flame tongues, fluctuating flames and steady flames. Carbon burn patterns on the walls of the combustor liner were also captured. From the data collected during the reacting runs, the pattern factor, profile factor, overall pressure loss and pressure loss factor were calculated. The non-reacting experiments performed using the PIV, produced three-dimensional velocity vector fields throughout the combustor. These experiments were performed at various flow rates, which gave an indication of which features of the combustor flow were affected by the flow rate. When comparing the individual PIV images alongside one another, the temporal nature of the combustor flow was also evident. The reacting experiments revealed a hot region of exhaust gas around the outer edge of the exhaust while there was a cooler region in the centre of the outlet flow. The PIV flowfield results revealed the reason for then hot outer ring-like region was due to the path the hot gasses would take. The hot combustor gas from the primary zone diverges outwards in the secondary zone then is further forced to the outside by the dilution recirculation zone. The hot flow then leaves the combustor along the wall while the cooler air from the jets leaves the combustor in the centre. The experiments performed produced a large variety of data that can be used to validate a number of aspects of combustor simulation using CFD. The non-reacting experimental data can be used to validate the turbulence models used and to evaluate how well the flow features were modelled or captured during the non-reacting stage of the combustor simulation process. The typical flow features such as jet penetration depths and the position and size of the recirculation regions are provided for effective comparison. The thermal results presented on the outlet plane of the combustor can be used for comparison with CFD results once combustion is modelled. Copyright / Dissertation (MEng)--University of Pretoria, 2010. / Mechanical and Aeronautical Engineering / unrestricted
|
10 |
Numerical Investigation on CO Emissions in Lean Premixed Combustion / 希薄予混合燃焼におけるCO排出に関する数値解析による研究Yunoki, Keita 23 March 2022 (has links)
京都大学 / 新制・課程博士 / 博士(工学) / 甲第23882号 / 工博第4969号 / 新制||工||1776(附属図書館) / 京都大学大学院工学研究科機械理工学専攻 / (主査)教授 黒瀬 良一, 教授 中部 主敬, 教授 岩井 裕 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM
|
Page generated in 0.044 seconds