The control of excessive water production in oil and gas producing wells is of increasing importance to the field operator, primarily when trying to maintain the survivability of a mature field from shut in. During the last two decades many chemicals have been studied and applied under the name of relative permeability modifier (RPM) to combat this problem. These chemicals were mostly bullheaded individually into the affected zones, consequently their application resulted in low to medium success, particularly in treating reservoirs suffering from matrix flow. It has been found that the disproportionate permeability reduction depends on the amount of polymer dispersed or absorbed by the porous rock. If single polymers are employed to treat excessive water production in a matrix reservoir they cannot penetrate deep into the formation rock because the polymer will start to build as a layer on the surface of the rock grains. As a result the placement of polymer into the formation will no be piston like and the dispersion over the rock pores will be uneven. To improve water shutoff technology a method of injecting chemicals sequentially is recommended provided that the chemical’s viscosity is increasing successively with the chemicals injected. / Experimentally confirmed, injecting chemicals sequentially provides better results for conformance control. The value of post treatment water mobility is conspicuously lowered by the method of applying injecting chemicals sequentially in comparison with the single chemical injection method. For instance, the residual resistance factor to water (Frrw) at the first cycle of brine flushing for this method is approximately five times higher than the Frrw obtained by injecting only one single chemical. Furthermore, for the second cycle of brine flushing Frrw is still higher by a ratio of about 2.5. In addition to this improvement residual resistance factor to oil Frro for this method is less than two which has been considered as the upper limit for conformance control in matrix reservoir. Accordingly injecting chemical sequentially can be applied for enhancing relative permeability modifier performance in matrix reservoir.

This work addresses the poroelastic effect on the processes involved in hydraulic fracturing and post-fracture production using a finite element based fully coupled poroelastic model which includes a triple system of wellbore-fracture-reservoir. A novel numerical procedure for modeling hydraulic fracture propagation in a poroelastic medium is introduced. The model directly takes into account the interaction of wellbore, hydraulic fracture and reservoir in a fully coupled manner. This allows realistic simulation of near fracture phenomena such as back stress and leak-off. In addition, fluid leak-off is numerically modeled based on the concept of fluid flow in porous media using a new technique for evaluating local pressure gradient. Besides, the model is capable of accommodating the zone of reduced pressure (including intermediate and fluid lag zones) at the fracture front so as to capture the behavior of fracture tip region more realistically. A fully coupled poroelastic model for gas reservoirs has been also developed using an innovative numerical technique. From the results of this study it has been found that fracture propagation pressure is higher in poroelastic media compared to that of elastic media. Also high formation permeability (in the direction normal to the hydraulic fracture) and large difference between minimum horizontal stress (in case of it being the smallest principal stress) and reservoir pressure reduce the rate of fracture growth. Besides, high pumping rate is more beneficial in elongating a hydraulic fracture whereas high viscous fracturing fluid is advantageous in widening a hydraulic fracture. It has been also shown that rock deformation, permeability anisotropy and modulus of elasticity can have a significant effect on fluid flow in a hydraulically fractured reservoir. Furthermore, it has been shown that long stress reversal time window and large size of stress reversal region can be caused by high initial pressure differential (i.e. the difference between flowing bottomhole pressure and reservoir pressure), low initial differential stress (i.e. the difference between maximum and minimum horizontal stresses) and low formation permeability in tight gas reservoirs. By taking advantage of production induced change in stress state of a reservoir, this study has also shown that a refracture treatment, if carried out in an optimal time window, can lead to higher economic gain. Besides, analysis of stress reversal region has depicted that a small region with high stress concentration in the vicinity of the wellbore could impede refracture from initiating at the desired place. Moreover, re-pressurization of the wellbore can result in further propagation of the initial fracture before initiation or during propagation of the secondary fracture.

Thesis (M.S.)--University of Oklahoma, 2005 / Title from title screen (viewed on Dec. 10, 2007). Title from document title page. Includes bibliographical references. Available in PDF format via the World Wide Web.

Not available / text

Gas wells suffer a decrease in productivity because of the formation of a liquid hydrocarbon “condensate” in the near wellbore area. This "condensate" forms near producing wells when the flowing pressure is below the reservoir fluid's dew point. Several methods have been shown to temporarily alleviate this problem, but eventually the condensate bank reforms and the productivity again decreases. The use of surfactants to alter the near wellbore wettability to neutral wetting is a potential longer term solution to liquid blocking in these reservoirs. This alteration increases the gas and liquid relative permeabilities and thereby the productivity by reducing the residual liquid saturation. This enhancement allows the accumulated liquid to flow and is durable as long as the wettability alteration is persistent. This solution has been shown to be successful through core flood experiments and field trials in high permeability sandstones, but no improvements had been observed in low permeability cores. As the global demand for energy increases, the petroleum industry has begun to develop unconventional (low permeability) assets, new techniques are needed to maintain and improve their productivity. Liquid blocking in these wells can have a much larger impact on both the gas and condensate production in such low permeability formations. Applying this technique increases both gas and condensate mobility and should increase the economic producing life of these wells. Core flood experiments were conducted to investigate the ability of a chemical treatment to alter the wettability of low permeability sandstones. Previous experimentation did not find any improvement because the increased capillary forces prevented the treatment solution from being easily displaced. This concealed the benefit achieved when the wettability was altered. These experiments recorded smaller relative permeability increases compared to higher permeability core floods, so super critical carbon dioxide was tested as an alternative solvent. While the new treatment was more injectable, it was not as successful at altering wettability. Progress has been made on a solution to liquid blocking in low permeability sandstones, but additional research needs to be completed to further optimize this method. / text

This work addresses the poroelastic effect on the processes involved in hydraulic fracturing and post-fracture production using a finite element based fully coupled poroelastic model which includes a triple system of wellbore-fracture-reservoir. A novel numerical procedure for modeling hydraulic fracture propagation in a poroelastic medium is introduced. The model directly takes into account the interaction of wellbore, hydraulic fracture and reservoir in a fully coupled manner. This allows realistic simulation of near fracture phenomena such as back stress and leak-off. In addition, fluid leak-off is numerically modeled based on the concept of fluid flow in porous media using a new technique for evaluating local pressure gradient. Besides, the model is capable of accommodating the zone of reduced pressure (including intermediate and fluid lag zones) at the fracture front so as to capture the behavior of fracture tip region more realistically. A fully coupled poroelastic model for gas reservoirs has been also developed using an innovative numerical technique. From the results of this study it has been found that fracture propagation pressure is higher in poroelastic media compared to that of elastic media. Also high formation permeability (in the direction normal to the hydraulic fracture) and large difference between minimum horizontal stress (in case of it being the smallest principal stress) and reservoir pressure reduce the rate of fracture growth. Besides, high pumping rate is more beneficial in elongating a hydraulic fracture whereas high viscous fracturing fluid is advantageous in widening a hydraulic fracture. It has been also shown that rock deformation, permeability anisotropy and modulus of elasticity can have a significant effect on fluid flow in a hydraulically fractured reservoir. Furthermore, it has been shown that long stress reversal time window and large size of stress reversal region can be caused by high initial pressure differential (i.e. the difference between flowing bottomhole pressure and reservoir pressure), low initial differential stress (i.e. the difference between maximum and minimum horizontal stresses) and low formation permeability in tight gas reservoirs. By taking advantage of production induced change in stress state of a reservoir, this study has also shown that a refracture treatment, if carried out in an optimal time window, can lead to higher economic gain. Besides, analysis of stress reversal region has depicted that a small region with high stress concentration in the vicinity of the wellbore could impede refracture from initiating at the desired place. Moreover, re-pressurization of the wellbore can result in further propagation of the initial fracture before initiation or during propagation of the secondary fracture.

Thesis (Ph. D.)--West Virginia University, 2008. / Title from document title page. Document formatted into pages; contains xiv, 258 p. : ill., maps. Includes abstract. Includes bibliographical references.

Thesis (M.S.)--West Virginia University, 2004 / Title from document title page. Document formatted into pages; contains xiii, 134 p. : ill. (some col.), maps (some col.). Vita. Includes abstract. Includes bibliographical references (p. 118-122).

Agriculture and, more recently, oil and gas development have contributed to extensive degradation and loss of temperate grasslands. I investigated the landscape-scale effects of oil and gas development, and roads, on grassland birds in southern Alberta using abundance, clutch size and nesting success data collected from 2010-2014. I estimated: (i) the distance at which there are effects of edge, and effects of shallow gas well density, using piecewise regressions; (ii) the locations and extent of habitat affected by infrastructure for obligate grassland species– Baird’s Sparrow (Ammodramus bairdii), Chestnut-collared Longspur (Calcarius ornatus) and Sprague’s Pipit (Anthus spragueii); and generalist species – Clay-colored Sparrows (Spizella pallida), Horned Lark (Eremophila alpestris), Savannah Sparrow (Passerculus sandwichensis), Vesper Sparrow (Pooecetes gramineus) and Western Meadowlark (Sturnella neglecta), and (iii) the total area affected by wells and roads. My findings suggest that the effects of roads, overall, extended to further distances than edge effects associated with natural gas wells, obligate species had more habitat affected by infrastructure than generalist species and shallow gas wells affected more habitat than did oil wells, due to their greater density on the landscape. Additionally, obligates, on average, were negatively affected by proximity to edge where as generalists were more productivity closer to edge. Reducing fragmentation caused by roads, minimizing the spread of non-native vegetation and management of cattle around gas wells could improve habitat quality for these focal species. / February 2016

The increase in unconventional shale gas extraction in Pennsylvania has resulted in an increased number of groundwater contamination claims. Well water quality was investigated in southern Butler County, PA where 387 unconventional gas wells have been drilled since 2006. A total of 121 households participated in a survey and 238 well water samples were tested. Specific conductivity, pH, and dissolved oxygen in these samples were measured in the field and seven anion concentrations and thirty metal concentrations were measured in the lab. A subset of 91 water wells was also tested for light hydrocarbons (methane, ethane, ethylene, propylene, propane, butane). Pennsylvania DEP file reviews were used to create GIS maps indicating legacy oil and gas, unconventional wells, and plot water testing results. Results indicate few wells had high quality groundwater, with 86% containing one or more contaminants above (secondary) Maximum Contaminant Levels, with manganese (56%), iron (47%), fluoride (18%), TDS (18%), pH (17%), aluminum (17%) the most common. / Bayer School of Natural and Environmental Sciences; / Environmental Science and Management (ESM) / MS; / Thesis;