The aim of the thesis is to get acquainted with the principle and function of functional generators. Furthermore, with their design using active elements that can be electronically controlled. The design and simulation results are presented in Chapter 4, which also shows schematics of simulated and measured circuits.

The aim of this work is design, realization, and measurement of wideband microwave generator, which is based on the ADF4350 frequency synthesizers. The generator uses the principle of mixing, for frequencies up to 2.2GHz. Higher frequencies are obtained through direct channels. The first part describes the theory of phase locked loop . The following section describes the parameters of the ADF4350 and their management. A PCB was also designed to control the generator with Atmel s AVR AT-mega32. The Generator software is written in AVR Studio in C programming language. The realized generator is housed in a stainless steel box and can be controlled using the keyboard and PC.

This project occupies with the creation modulated signal generator in MATLAB. There are explicit basic princips of modulation PSK, M-QAM, princip of system with spread spektrum and princip of access OFDM and MC-CDMA. Next there are explicit basic parametres and possibilities configuration of conversion analog PCI card CompuGen 4302, which serves as D/A convertor of signals created by PC.

The main objective of the master`s thesis was to prove, if permanent magnet synchronous generator made by company JULI Motorenwerk s.r.o. could reach higher maximum active power with active rectifier than with six-pulse bridge rectifier. For this reason a mathematical model was made in Matlab/Simulink. The influence of the rectifiers with various kinds of loading was observed and compared by simulations on output variables, like line-to-line voltage and active power. The simulations were also compared with measurement.

This master’s thesis deals with utilization of biomass for micro cogeneration. The theoretical part of the master’s thesis defines main terms of the master’s thesis, which is biomass and cogeneration. The practical part of the master’s thesis is focused on the design and manufacturing of small micro cogeneration unit based on a small membrane steam engine. It means design of two steam generators to produce steam for the membrane steam engine. It will be also carried out design and production of membrane steam engine which is fitted with a small BLDC generator including electrical part for power output and measuring parameters. It will be made several measurements with the steam engine including measuring power output characteristic of the steam engine and measuring loading characteristics of the generator.

Master`s thesis deals with the economic situation of the company STEL-INVEST, Ltd., which will be basis for the decision to extend the entrepreneurial activity by the new service. The company STEL-IVEST, Ltd. is currently engaged in services and maintenance in the field of telecommunication.

The aim of thesis entitled steam turbine is a condensing steam turbine with steam extraction, in twin-shaft implementation for municipal waste-incineration plant. The first part of the work is focused on the design used and the selected concept turbine. The second part is engaged in thermodynamic calculation of backpressure and condensing part. The end is devoted to technical – economic comparison with other possible conceptual variants.

The thesis deals with a project of a steam generator heated with liquid sodium. The first section describes some types of steam generators at nuclear power plants which have been projected or put into use. The next part presents a draft concept of the steam generator, solved by this work. The implementation of the steam generator module has been selected from several options, based on the thermal, hydraulic and stress calculations and on the chosen criteria. The conclusion of this thesis deals with the evaluation of the final solution in terms of nuclear safety and technical solutions, and compares this solution to similar projects following various criteria.

This paper describes the design of control, measurement and power electronics department for dynamic loading of electronically commutated motors with electric brakes. After comparing the advantages and disadvantages of possible conceptions the proposal focuses on electric brake operating in generator mode and the value of load is controlled by the current dissipated in a dummy load.

The main goal of this thesis is the examination of hydraulic characteristics for different cavity nozzles, influence of liquid rotation and visualization of cavitating flow. Thesis is divided into two parts, theoretical and practical. Theoretical part deals with the description of cavity - creation, development and its extinction. This part also contains description of vortex flow and basic vertex models. Practical part compares nozzles performance experimentally. The aim of experiment was to measure hydraulic characteristics and their comparison. Jet performance was judged using visualizations and measured data was processed in Microsoft Excel and Parametr.