Key factors that influence the design of paved and unpaved roads are the strength and stiffness of the pavement layers. Among other factors, the strength of pavements depends on the thickness and quality of the aggregates used in the pavement base layer. In India and many other countries, there is a high demand for good quality aggregates and the availability of aggregate resources is limited. There is a need for the development of sustainable construction methods which can handle aggregate requirements with least available resources and provide good performance. Hence it is imperative to strive for alternatives to achieve improved quality of pavements using supplementary potential materials and methods. The strength of pavement increases with increase in the thickness of the base which has a direct implication on construction cost whereas decreasing the thickness of the base makes it weak which results in low load bearing capacity especially for unpaved roads. The use of different types of geosynthetics like geocell and geogrid are a potential and reliable solution for the lack of availability of aggregates and studies are conducted in this direction. To better understand the performance of any geosynthetically reinforced base layers, it is essential to characterize the pavement material by studying the behavior of these materials under static as well as repeated loading. For unpaved roads, the base layer, made of granular aggregates plays a crucial role in the reduction of permanent deformation of the pavements. The resilient modulus (Mr) of these materials is a key parameter for predicting the structural response of pavements and for characterizing materials in pavement design and evaluation. Usually, during the design of flexible pavements, pavement materials are treated as homogeneous and isotropic. The use of rollers in the field during pavement construction leads to a higher compaction of material in the vertical direction which introduces stress-induced anisotropy in the base material. The effect of stress-induced anisotropy on the properties of the granular material is studied and discussed in the first part of the research by conducting repeated load triaxial tests. Isotropic consolidated and anisotropically consolidated samples were prepared to investigate the behavior of base materials under stress induced anisotropic conditions. An additional axial load was applied on the isotropically consolidated sample to create anisotropically consolidated sample. The axial loading was provided such that the stress ratio (σ1/σ3), during anisotropic consolidation was kept constant for all the tests at different confining pressures. The effect of repeated loading on the permanent deformation and the resilient modulus for both isotropically and anisotropically consolidated samples, at different confining pressure and loading conditions, are discussed. The behavior of both anisotropically and isotropically consolidated samples has been explained using the record of the excess pore pressures generated during the experiments. The experimental studies show that the permanent strains measured in the vertical direction of the anisotropically consolidated samples are less compared to the results obtained for isotropically consolidated samples. The resilient moduli of the anisotropically consolidated samples were also observed to be higher than that of the isotropically consolidated sample. The study conducted on the pore pressure of both the samples explains better performance of the anisotropically consolidated samples. The studies showed that the isotropically consolidated samples showed higher pore pressures compared to the anisotropically consolidated specimens. Another factor which influences the resilient modulus of the pavement materials is the geosynthetic reinforcement. Geocell and geogrid reinforced triaxial samples were prepared to study the effect of reinforcement in the resilient modulus of the base materials. From the literature, it can be seen that most of the research in the triaxial testing equipment were carried out in the non-destructive range of confining pressure and deviatoric stress. Several studies have been conducted by the researchers to visualize the pavement response in the elastic range. However, the studies in the plastic creep range and incremental collapse range were highly limited. In the current study, testing is carried out on the triaxial samples for two different stress ranges. In the first sections, loading was applied in the elastic and elastic shakedown range as per AASTHO T-307. For various loading sequences, a comparative analysis has been done for the resilient modulus of the geogrid and geocell. In the next section, the loading was applied on the sample in the plastic shakedown range and incremental collapse range. The results of the permanent strains and resilient modulus of the sections are compared with the corresponding results of the unreinforced section. In the plastic shakedown and incremental collapse range also the permanent strains of reinforced samples were less than those observed in the unreinforced section. The performance of geosynthetically reinforced pavement layers can be better understood by studying the samples prepared under realistic field conditions. In the case of triaxial experiments the sample size is very less compared to the field conditions and the effect of other pavement layers on the performance of the base layers cannot be studied on triaxial samples. Samples were prepared in the laboratory by modeling the pavement sections in a cuboidal tank, in which different pavement layers are laid one over the other, and a static loading or repeated loading is applied to overcome the bottleneck of small sample size in the triaxial setup. The experiments were conducted on the unreinforced section; geocell reinforced section and geogrid reinforced section placed above strong and weak subgrade. The results of the study are examined regarding the resilient deformation, permanent deformation, pressure distribution and strain measurements for different thicknesses of base layers under repeated loading. The initial parts of the study present the results of experiments and analysis of the results to understand the behavior of geocell reinforced granular base during repeated loading. In this study, an attempt is made to understand the various factors which influence the behavior of geocell reinforced granular base under repeated loading by conducting plate load tests. The loads applied on the pavements are much higher than the standard axle loading used for the design of pavements. High pressure was applied on all the test sections to simulate these higher loading conditions in the field. The optimum width and height of the geocell to be provided, to get maximum reduction in permanent deformation is studied in detail. The effect of resilient deformation of reinforced and unreinforced base layers is quantified by calculating the resilient modulus of these layers. The studies showed that the geocell reinforcement was effective in reducing the permanent and resilient deformations of base layer when compared to the unreinforced samples. The resilient modulus calculated was higher for the reinforced sample with half of the thickness of the unreinforced sample. The effect of reinforcement in the stress distribution within the base layer is also studied by measuring the pressures at different depths of the base layer. The results showed that the pressure getting transferred to the subgrade level was much lower in the case of geocell reinforced base layer. The ultimate aim of any pavement design method is to reduce the distress in the subgrade level and thus leading to increased life of pavements. Pressures at the subgrade level for reinforced and unreinforced sections are studied in detail, the main parameter under study being the stress distribution angle, to investigate the distress in the subgrade level. It was observed that the geocell reinforced sample showed higher stress distribution angle when compared to its unreinforced counterpart. Another important factor that has to be studied is the strains at the subgrade level since it is the governing factor of causing rutting in the pavements. From the experiments conducted in the study, it was shown that the reinforcement is very effective in reducing the strains at the top of subgrades. The implications of the current study are brought out in terms of improved pavement performance as the carbon emission reductions. It is important to analyze the performance of reinforced section under realistic field conditions. To do that experiment were conducted on reinforced and unreinforced base layers placed on top of weak subgrade material. The study showed that the reinforcements are effective in reducing the deformations under weak subgrade conditions also but not as effective as it was under strong subgrade case. The experimental results were then validated with the two-dimensional mechanistic-empirical model for geocell reinforced unpaved roads for predicting the performance of pavements under a significant number of cycles. The modified permanent deformation model which incorporates the triaxial test results and strains measured directly from the base sections were used to model and validate. Plate load experiments were also conducted on base layers reinforced with geogrid to understand the behavior of these reinforced samples under repeated loading. Several factors like the width of the geogrid to be provided and the depth of placing the geogrid in the base layer were studied in detail to achieve maximum reduction in deformations. Permanent and resilient deformation studies were carried out for both reinforced and unreinforced sections of varying thicknesses, and a comparison was made to understand the effect of reinforcement. The geogrid reinforcement could effectively reduce the permanent and resilient deformations when compared to the unreinforced sections. A study was also carried out on the resilient modulus, which explained the better performance of the geogrid reinforced samples by showing higher resilient modulus for reinforced samples than the unreinforced specimens. The performance of the geogrid reinforced base layers was further verified by studying the pressure distribution at the subgrade level and by calculating the stress distribution angle corresponding to the reinforced and unreinforced samples. The strains at the subgrade level were also studied and compared with the unreinforced sample which showed a better performance of geogrid reinforced samples. The results from the strain gauges fixed in the geogrid were further used to model and validate the permanent deformation model. Experiments were conducted on geogrid-reinforced base layer placed above weak subgrade conditions. The results showed that the reinforcement was effective in reducing the deformations under weak subgrade conditions also. Apart from conducting the laboratory studies, experimental results were numerically modeled to accurately back-calculate the resilient moduli of the layers used in the study. 3D numerical modeling of the unreinforced and honeycomb shaped geocell reinforced layers were carried out using finite element package of ANSYS. The subgrade layer, geocell material, and infill material were modeled with different material models to match the real case scenario. The modeling was done for both static and repeated load conditions. The material properties were changed in a systematic fashion until the vertical deformations of the loading plate matched with the corresponding values measured during the experiment. The experimental study indicates that the geocell reinforcement distributes the load in the lateral direction to a relatively shallow depth when compared to the unreinforced section. Numerical modeling further strengthened the results of the experimental studies since the modeling results were in sync with the experimental data.

Scrap tyres provide numerous advantages from the viewpoint of civil engineering practices. Scrap tyres are light weight, have high vibration absorption, high elastic compressibility, high hydraulic conductivity, and temperature isolation potential. Scrap tyres have a thermal resistivity that is about seven times higher than soil; they produce low earth pressure and absorb vibrations. Many new techniques have emerged with time to utilize these advantageous characteristics for practical purposes in civil engineering. Though current reuse and recovery of scrap tyres has reduced the amount of landfills, but still there is a need for developing additional practices for the reuse of scrap tyres. Moreover, most of present practices do not use its vibration absorption capacity efficiently. To use the scrap tyres as individual material or mixed with soil in civil engineering applications, the systematic understanding of static and dynamic properties of sand-rubber mixtures (SRM) are of prime importance. In the present study an attempt has been made to characterize the SRM to use them as low-cost isolation material for low-to-medium rise buildings. Proposal of this isolation system using SRM is addressed in this study in four parts; in the first part, the estimation of shear strength and volumetric characteristics of the SRM were carried out. A total of seven different rubber sizes (six sizes of granulated rubber; 2 - 1 mm; 4.75 - 2 mm; 5.6 - 4.75 mm; 8 - 5.6 mm; 8 - 9.5 mm; 12.5 - 9.5 mm and one size of tyre chips; 20 - 12.5 mm) were considered for characterizing the SRM, and the rubber size which has higher shear strength characteristics is identified as optimum size for further studies. Second part deals with the effect of reinforcement on SRM with higher rubber content (50% and 75% rubber by volume). In the third part, dynamic properties of selected SRM combination with and without reinforcement were generated from experimental studies. In the last part, the numerical analysis was carried out using finite element program Strand7 to find out optimum dimension of proposed isolation scheme and reduction of spectral accelerations. In addition, the laboratory model tests were also carried out on square footing supported on unreinforced and reinforced SRM. The relative performances of reinforcement on settlement characteristics of SRM for 50% and 75% SRM have been compared with unreinforced SRM. Engineering behaviour of SRM has been studied by considering different rubber sizes and compositions by carrying out large scale direct shear test and Unconsolidated Undrained (UU) triaxial test. The shear strength characteristics such as peak shear stress, cohesion, friction angle, secant/elastic modulus, volumetric strain, failure and ultimate strength, ductility/brittleness index, and energy absorption capacity of sand and SRM were determined. The optimum percentage rubber content based on maximum shear strength and energy absorption capacity has been arrived. The granulated rubber size (12.5 - 9.5 mm) and percentage ratio, 30% by volume is found to be optimum size and content, which gives the maximum energy absorption capacity and lower brittleness index values compared to other rubber sizes. This chapter also describes the applicability of concept of Response Surface Methodology (RSM) to identify an approximate response surface model from experimental investigations on the engineering properties of sand and SRM. The experimental data were quantitatively analyzed by multiple regression models by correlating response variables with input variables in this study. To consume more tyres in SRM, rubber mix of 50 % and 75 % mixes are studied and these SRM results in lower shear strength and higher volume change when compared to 30 % SRM. To improve shear strength and reduce compressibility, geosynthetic reinforcement study has been carried out for 50% and 75% rubber by volume. Here geotextile, geogrid and geonets were used as reinforcement and number of layers and spacing between layers were varied. Finally type of reinforcement, number of layers and optimum spacing are arrived for the optimum rubber size of 12.5 - 9.5 mm for reinforced SRM. This study found that 4 layers with equal spacing of geotextile for 50 % SRM and geonet for 75 % SRM shows better strength when compared to other combinations. Further dynamic properties such as shear modulus and damping values at different strain level are estimated for red soil, sand, 30 % SRM and unreinforced and reinforced 50 % and 75 % SRM by carrying out resonant column tests and cyclic triaxial tests. The normalized shear modulus and damping ratio curves have been developed for these materials. The experimental results indicate that, shear modulus increases for 30% rubber by volume when compared to sand, thereafter the shear modulus values decreased with a further increase in rubber content in SRM. Whereas the damping ratio increases with increasing rubber content in SRM. For sand and SRM, with an increase in confining pressure shear modulus increases and damping ratio decreases. Based on the comprehensive set of experimental results, a modified hyperbolic model has been proposed. These properties are further used in the numerical analysis to find out the effectiveness of SRM as isolation material. Numerical dynamic analysis has been carried out on a 2-D finite element model of the soil-foundation-structure system. The building model has been generated considering the typical G+2 building resting on 20 m thick soil followed by rock depth and foundation is placed at 2.0 m below ground level. The beams and columns in the superstructure are modeled using 2-D frame elements. The soil column has been modeled using 4-noded 2-D plane strain plate elements. Considering the transmitting boundary condition, viscous dampers are implemented at the base of the computational soil domain in order to mitigate the reflective effects of waves. The Newmark family method (average acceleration method) has been used to calculate the displacement, velocity and acceleration vectors. Comprehensive numerical simulations have been carried out on the soil-foundation-structure system by varying rubber content in SRM (30%, 50% and 75% granulated rubber by volume), depth and thickness of SRM around footing and considering two input earthquake acceleration time history. It was found that earthquake vibrations are considerably reduced for SRM with higher rubber content. The optimum dimension of SRM giving maximum reduction in shaking level is found to be 3B below the footing and 0.75B (where B is the width of footing) on the side of the footing. Generally, the shaking levels at different floor can be reduced by 30-50%, with the use of 75% SRM. The results also indicated that the effectiveness of proposed system would depend on the characteristics of ground motion. To study the bearing capacity of square footing on SRM, laboratory model tests were carried out on square footing supported on unreinforced and reinforced SRM. The SRM combination which have been used for numerical studies are used in this model studies to know the bearing capacity and settlement characteristics. The optimum dimension of SRM around footing has been constructed. Model tests results show that, the bearing capacity decreases and settlement increases steadily with the increase in rubber content in SRM. Addition of reinforcement to SRM significantly improved the bearing capacity and reduced settlement characteristics. Reinforced SRM may be used as an effective low cost isolation scheme to reduce earthquake vibrations.