Spelling suggestions: "subject:"glycols"" "subject:"glycolsis""
61 |
Tegdma induction of apoptotic proteins in pulp fibroblastsBatarseh, Ghada January 2011 (has links)
Indiana University-Purdue University Indianapolis (IUPUI) / Monomers like triethylene glycol dimethacrylate (TEGDMA) leach from dental composites and adhesives due to incomplete polymerization or polymer degradation. The release of these monomers causes a variety of reactions that can lead to cell death. This death can be either necrotic, which is characterized mainly by inflammation and injury to the surrounding tissues, or apoptotic, which elicits little inflammatory responses, if any at all. TEGDMA-induced apoptosis in human pulp has been reported recently. However, the molecular mechanisms and the apoptotic (pro and anti) proteins involved in this process remain unclear.
The objective of this study was to determine the apoptotic proteins expressed or suppressed during TEGDMA-induced apoptosis. Human pulp fibroblasts (HPFs) were incubated for 24 hours with different TEGDMA concentrations (0.125-1.0 mM). Cytotoxicity was determined using the cytotoxicity Detection KitPLUS (Roche Applied Science, Mannheim, Germany). TEGDMA was shown to cause cell cytotoxicity at concentrations of 0.50 mM and up. The highest concentration with no significant cytotoxicity was used. Cells were incubated with or without 0.25 mM TEGDMA for 6 h and 24 h. Cell lysates were then prepared and the protein concentrations determined using the Bradford protein assay. A Human Apoptosis Array kit (Bio-Rad Hercules, CA ) was utilized to detect the relative levels of 43 apoptotic proteins. The results of this study showed statistically significant increases of multiple examined pro-apoptotic proteins. The anti-apoptotic proteins were also altered. Pro-apoptotic proteins involved in the intrinsic and extrinsic apoptotic pathways were increased significantly. The results indicated that TEGDMA has effects on both the extrinsic and intrinsic apoptotic pathways.
|
62 |
Nerve guides manufactured from photocurable polymers to aid peripheral nerve repairPateman, C.J., Harding, A.J., Glen, A., Taylor, C.S., Christmas, C.R., Robinson, P.P., Rimmer, Stephen, Boissonade, F.M., Claeyssens, F., Haycock, J.W. 2015 February 1914 (has links)
Yes / The peripheral nervous system has a limited innate capacity for self-repair following injury, and surgical intervention is often required. For injuries greater than a few millimeters autografting is standard practice although it is associated with donor site morbidity and is limited in its availability. Because of this, nerve guidance conduits (NGCs) can be viewed as an advantageous alternative, but currently have limited efficacy for short and large injury gaps in comparison to autograft. Current commercially available NGC designs rely on existing regulatory approved materials and traditional production methods, limiting improvement of their design. The aim of this study was to establish a novel method for NGC manufacture using a custom built laser-based microstereolithography (muSL) setup that incorporated a 405 nm laser source to produce 3D constructs with approximately 50 mum resolution from a photocurable poly(ethylene glycol) resin. These were evaluated by SEM, in vitro neuronal, Schwann and dorsal root ganglion culture and in vivo using a thy-1-YFP-H mouse common fibular nerve injury model. NGCs with dimensions of 1 mm internal diameter x 5 mm length with a wall thickness of 250 mum were fabricated and capable of supporting re-innervation across a 3 mm injury gap after 21 days, with results close to that of an autograft control. The study provides a technology platform for the rapid microfabrication of biocompatible materials, a novel method for in vivo evaluation, and a benchmark for future development in more advanced NGC designs, biodegradable and larger device sizes, and longer-term implantation studies.
|
Page generated in 0.0384 seconds