The main purpose of this thesis is to improve the fundamental knowledge of non-isothermal tempering of martensite phase and its effects on the reduction in hardness (softening) with respect the base metal occurring at the heat affected zone (HAZ) of resistance spot welded dual-phase (DP) steels. This thesis also aims at understanding the influence of HAZ-softening on the joint performance of various DP steel grades. The tempering of martensite occurring at the sub-critical HAZ (SC-HAZ) of resistance spot welded DP600, DP780 and DP980 steels has been systematically evaluated by microhardness testing through Vickers indentation and the degree of tempering has been correlated to the HAZ-softening. From the joint performance analysis of similar and dissimilar steel grade combinations assessed through standardized testing methods, three important issues have been targeted: a) the joint strength (maximum load to failure), b) the location of failure (failure mode), and c) the physical characteristic of the weld that determines certain type of failure (weld nugget size). In addition, a partial tensile test has been conducted in order to evaluate the initiation of failure in dissimilar steel grade combinations. It has been shown that HAZ-softening lowered the weld size at which transition from interfacial to pullout failure mode takes place along with increased load-bearing capacity and higher energy absorption. Thus, it is concluded from mechanical testing that HAZ-softening benefits the lap-shear tensile joint performance of resistance spot welded DP steels by facilitating pullout failures through failure initiation at the SC-HAZ (tempered region). Instrumented nanoindentation testing was employed to further investigate HAZ-softening along the SC-HAZ by evaluating individual phases of ferrite matrix and tempered martensite islands. Although the ferrite matrix presented a slight reduction in hardness at nanoscale, higher reduction in hardness (softening) resulted for tempered martensite; thus confirming that tempered martensite is the major contributor to softening at micro-scale. A comparison between nanohardness and microhardness testing made at different distances from the line of lower critical temperature of transformation (Ac1) allowed revealing the actual extension of the SC-HAZ. In this regard, good correlation was obtained between nanohardness results along the SC-HAZ and the microstructural changes analyzed by electron microscopy (i.e., the tempering of martensite occurring at various distances far from Ac1 was correlated to low temperature tempering of dual phase steels). An in-depth analysis of the tempering of martensite phase at high temperature in DP steel subjected non-isothermal conditions i.e., rapid heating, extremely short time at peak temperature and rapid cooling (resistance spot welding), has been carried out mainly through analytical transmission electron microscopy (TEM). In addition, an isothermal tempering condition (i.e., slow heating and long time at peak temperature) in DP steel has been evaluated for complementing the analysis. Both non-isothermal and isothermal conditions have been correlated to the softening behaviour. TEM analysis of the base metal in the DP steel indicated that the morphology of the martensite phase is dependent on its carbon content, and its tempering characteristics are similar to that of equal carbon containing martensitic steel. The isothermally tempered structure is characterized by coarsening and spheroidization of cementite (θ) and complete recovery of the martensite laths; whereas precipitation of fine quasi-spherical intralath θ-carbides, coarser plate-like interlath θ-carbides, decomposition of retained austenite into elongated θ-carbides, and partial recovery of the lath structure were observed after non-isothermal tempering of DP steel. This difference in tempering behaviour is attributed to synergistic effect of delay in cementite precipitation due to higher heating rate, and insufficient time for diffusion of carbon that delays the third stage of tempering process (cementite coarsening and recrystalization) during non-isothermal. The finer size and the plate-like morphology of the precipitated carbides along with the partial recovery of the lath structure observed after non-isothermal tempering strongly influenced the softening behaviour of DP steel. The chemical analysis of θ-carbides through extraction replicas for three different DP steels revealed that the chemistry of the carbides is inherited from the parent DP steel during non-isothermal tempering at high temperature confirming that non-isothermal tempering DP steel is predominantly controlled by carbon diffusion.

The main purpose of this thesis is to improve the fundamental knowledge of non-isothermal tempering of martensite phase and its effects on the reduction in hardness (softening) with respect the base metal occurring at the heat affected zone (HAZ) of resistance spot welded dual-phase (DP) steels. This thesis also aims at understanding the influence of HAZ-softening on the joint performance of various DP steel grades. The tempering of martensite occurring at the sub-critical HAZ (SC-HAZ) of resistance spot welded DP600, DP780 and DP980 steels has been systematically evaluated by microhardness testing through Vickers indentation and the degree of tempering has been correlated to the HAZ-softening. From the joint performance analysis of similar and dissimilar steel grade combinations assessed through standardized testing methods, three important issues have been targeted: a) the joint strength (maximum load to failure), b) the location of failure (failure mode), and c) the physical characteristic of the weld that determines certain type of failure (weld nugget size). In addition, a partial tensile test has been conducted in order to evaluate the initiation of failure in dissimilar steel grade combinations. It has been shown that HAZ-softening lowered the weld size at which transition from interfacial to pullout failure mode takes place along with increased load-bearing capacity and higher energy absorption. Thus, it is concluded from mechanical testing that HAZ-softening benefits the lap-shear tensile joint performance of resistance spot welded DP steels by facilitating pullout failures through failure initiation at the SC-HAZ (tempered region). Instrumented nanoindentation testing was employed to further investigate HAZ-softening along the SC-HAZ by evaluating individual phases of ferrite matrix and tempered martensite islands. Although the ferrite matrix presented a slight reduction in hardness at nanoscale, higher reduction in hardness (softening) resulted for tempered martensite; thus confirming that tempered martensite is the major contributor to softening at micro-scale. A comparison between nanohardness and microhardness testing made at different distances from the line of lower critical temperature of transformation (Ac1) allowed revealing the actual extension of the SC-HAZ. In this regard, good correlation was obtained between nanohardness results along the SC-HAZ and the microstructural changes analyzed by electron microscopy (i.e., the tempering of martensite occurring at various distances far from Ac1 was correlated to low temperature tempering of dual phase steels). An in-depth analysis of the tempering of martensite phase at high temperature in DP steel subjected non-isothermal conditions i.e., rapid heating, extremely short time at peak temperature and rapid cooling (resistance spot welding), has been carried out mainly through analytical transmission electron microscopy (TEM). In addition, an isothermal tempering condition (i.e., slow heating and long time at peak temperature) in DP steel has been evaluated for complementing the analysis. Both non-isothermal and isothermal conditions have been correlated to the softening behaviour. TEM analysis of the base metal in the DP steel indicated that the morphology of the martensite phase is dependent on its carbon content, and its tempering characteristics are similar to that of equal carbon containing martensitic steel. The isothermally tempered structure is characterized by coarsening and spheroidization of cementite (θ) and complete recovery of the martensite laths; whereas precipitation of fine quasi-spherical intralath θ-carbides, coarser plate-like interlath θ-carbides, decomposition of retained austenite into elongated θ-carbides, and partial recovery of the lath structure were observed after non-isothermal tempering of DP steel. This difference in tempering behaviour is attributed to synergistic effect of delay in cementite precipitation due to higher heating rate, and insufficient time for diffusion of carbon that delays the third stage of tempering process (cementite coarsening and recrystalization) during non-isothermal. The finer size and the plate-like morphology of the precipitated carbides along with the partial recovery of the lath structure observed after non-isothermal tempering strongly influenced the softening behaviour of DP steel. The chemical analysis of θ-carbides through extraction replicas for three different DP steels revealed that the chemistry of the carbides is inherited from the parent DP steel during non-isothermal tempering at high temperature confirming that non-isothermal tempering DP steel is predominantly controlled by carbon diffusion.

Bead-on-plate laser welds were made on an industrially produced DP780 steel to determine the effect of normalized welding heat input on the microstructure and mechanical properties within the weld fusion zone (FZ) and heat affected zone (HAZ) with reference to the base material (BM) mechanical properties. Normalized welding heat input was calculated using an established model from the literature utilizing measurements from the weld cross-section microstructures along with known materials properties. Microhardness profiles and optical microscopy were employed to evaluate materials properties and microstructural changes across the various microstructural zones of each weld. The mechanical properties of the welds were evaluated globally through standard ASTM tensile specimens as well as through a series of specialized mechanical testing sample geometries which examined the properties of individual microstructural zones. These specialized sample geometries included non-standard uniaxial and plain strain tension where effective stress and effective strains were used to compare the mechanical properties across samples. It was determined that there was a good correlation between ASTM standard samples and the specialized sample geometries employed in this study and that the UTS and YS values obtained in both cases were comparable. Sigmoidal decay behaviour was observed in the UTS and YS with increasing heat input for both the FZ and HAZ of all welds. It was found that welds with heat inputs greater than 60 J/mm2 had both a UTS and YS which were significantly depressed in the FZ and HAZ when compared to the base material values. Conversely, welds with heat inputs below 36.3 J/mm2 were found to have a UTS and YS in both the FZ and HAZ microstructural zones which were above the values determined for the BM. When global weld properties were tested, it was found that welds with a heat input greater than 60.0 J/mm2 failed within the HAZ while welds with heat inputs below 36.3 J/mm2 failed within the BM. It has been shown that there is a significant correlation between the heat inputs of laser welded DP steels and both the mechanical properties and microstructural features of the various microstructural zones as well as the location of failure during weld tensile testing. It has also been demonstrated that the mechanical properties of weld microstructural zones can be qualitatively evaluated using specialized tensile testing geometries. / Thesis / Master of Applied Science (MASc)

<p>Advanced high strength steels, such as dual-phase and martensitic steels, are increasingly being used by automakers to decrease the thickness of steel sheet used in parts without sacrificing part strength. When welded, the martensite within the dual-phase and martensitic steel microstructures tempers, reducing the heat-affected zone (HAZ) hardness compared to the base material, locally reducing strength. This process is known as HAZ softening. HAZ softening has been well studied; however, the kinetics of this process has not been quantified and the processes responsible for HAZ softening have not been examined. This thesis investigated both of these topics.</p> <p>HAZ softening was modelled using the Johnson-Mehl-Avrami-Kolmogorov (JMAK) equation. As the thermal profile during welding is non-isothermal, the effects of temperature and time on steel tempering kinetics could not be separated by examining post-welded properties. The effects of tempering temperature and time were separated through a series rapid isothermal tempering experiments. Hardness data from these experiments allowed the HAZ softening rate to be empirically quantified through fitting the JMAK equation. This material model was then validated by predicting HAZ softening in laser and resistance spot welds. Although the fitted JMAK constants could be used to predict post-weld HAZ hardness, they did not agree with the classic literature values associated with martensite tempering.</p> <p>To understand why the JMAK coefficients did not match those of the classic martensite tempering literature, the softening data from one of the martensitic steels was re-examined. This study revealed that the softening process was a combination of two processes: carbide nucleation and carbide coarsening. The activation energies calculated for each process matched the classic literature values. Carbide coarsening dominated during tempering, which had a non-linear relation with change in hardness. The relationship between carbide coarsening and hardness was responsible for the softening kinetics measured from the rapid tempering experiments.</p> / Doctor of Philosophy (PhD)

No description available.