Thesis (Ph. D.)--University of Melbourne, 1996. / Typescript (photocopy). Includes bibliographical references (leaves 190-195).

Thesis (M.S.)--Oregon State University, 2010. / Printout. Includes bibliographical references (leaves 195-198). Also available on the World Wide Web.

Thesis (M.S.)--Rochester Institute of Technology, 1994. / Typescript. Includes bibliographical references (leaves 234-235).

Call number: LD2668 .T4 1952 K43 / Master of Science

Call number: LD2668 .T4 1952 L9 / Master of Science

published_or_final_version / Mechanical Engineering / Doctoral / Doctor of Philosophy

No description available.

No description available.

M.Ing. / Since the promulgation of the Montreal Protocol many refrigerants needed to be phased out. R-22, which is a widely used refrigerant in refrigeration systems, was one of these. Many replacements have been found throughout the years but very few have the same refrigeration capacity without being penalised by an increase in pressure drop. R-407C is one of the refrigerants having the potential to replace R-22 as it has the same theoretical coefficient of performance and has a lower global warming potential. However, due to its zeotropic characteristics there is a degradation in heat transfer during evaporation and condensation attributed to mass transfer resistance. Thus, augmentation techniques are needed not only to increase the heat capacity, but also to achieve an increase without incurring an excessive pressure drop. One approach to cope with this problem is to make use of the recently developed herringbone micro-fin tubes. Unfortunately very little data exists for refrigerants undergoing condensation inside herringbone micro-fin tubes. There is also little pressure drop information available for this type of tube. An experimental set-up was designed to determine the characteristics of this type of tube due to the scarcity of information. With the aid of current literature, various techniques were used to determine the pressure drops inside the herringbone micro-fin tube. One of these techniques was the use of the Kattan-Thome-Favrat flow regime map which helped to identify the flow patterns inside the tube. Knowledge of the type of flow occurring inside the tube helped to clarify the behaviour of the pressure drop relationships. The type of refrigerant being used also affected the behaviour of the pressure drop curves. A low-pressure refrigerant had a higher pressure drop due to the high vapour velocities achieved. Another cause for excessive pressure drop is the friction created by the high velocity vapour and condensate inside the tube. Many relationships for the friction factor exist and these are used to analyse the experimental data.The experimental facility comprised of a vapour compression loop and a water loop. The vapour compression loop consisted of a hermetically sealed compressor with a cooling capacity of 9.6 kW, a manually operated expansion valve and an evaporator. Three condensers were tested, namely a smooth tube, a helical micro-fin tube, and a herringbone micro-fin tube. The condensers were of the tube-in-tube type with the refrigerant flowing in the inner tube and the water in counter flow in the annulus. The hot water loop was used as a source for the evaporator and a cold loop as a heat sink for the condenser. Three refrigerants were tested, namely R-22, R-134a, and R-407C, all operating at a nominal saturation temperature of 40°C and at mass fluxes between 300 and 800 kg/m 2s. Accurate sensors and transducers were used to measure the temperatures, pressures, and mass flows at predefined points. Video cameras were attached to sight glasses to aid in the identification of the type of flow regime. Data were captured using a computerised data acquisition programme designed specifically for use with the experimental study. The experimental results showed that transition between the annular and intermittent flow regimes occurred at around 25% vapour quality for the herringbone micro-fin tube, as opposed to 30% for the helical micro-fin tube and 50% for the smooth tube. Pressure drops for the herringbone micro-fin tube were higher than those for the smooth tube but slightly lower than those for the helical micro-fin tube when using refrigerants R-22 and R-134a. The correlation of Liebenberg was modified for the pressure drops inside the herringbone micro-fin tube and gave a mean deviation of 12%. The efficiency ratio for the herringbone tube using R-22 was 1.85 and 1.69 when compared with the helical micro-fin and smooth tube respectively. For R-134 the efficiency ratio was 2.02 and 2.13 when compared with the helical micro-fin and smooth tube respectively, while for R-407C it was 1.58 and 1.26 for the two respectively. It was also concluded that R-407C could be used as a replacement refrigerant for R-22when used with a herringbone micro-fin tube.

<p>The demand for heat pumping technologies is expected to see tremendous growth over the next century. Traditional vapor compression cycles are approaching practical limits of efficiency and running out of possibilities for environmentally friendly and safe refrigerants. As a result, there is an increasing interest in pursuing non-vapor compression technologies that can achieve higher efficiencies with alternative working fluids. The chemical looping heat pump (CLHP) investigated here utilizes a chemical reaction to alternate a working fluid between more and less volatiles states. This allows the main compression to take place in the liquid phase and enables the utilization of a range of different working fluids that would not be appropriate for vapor compression technology. </p> <p> </p> <p>Thermodynamic models were developed to assess the potential performance of a chemical looping heat pump driven by electrochemical cells. A number of potential working fluids were identified and used to model the system. The thermodynamic models indicated that the chemical looping heat pump has the potential to provide 20% higher COPs than conventional vapor compression systems. </p> <p> </p> <p>An experimental test stand was developed to investigate the efficiency with which the electrochemical reactions could be performed. The working fluids selected were isopropanol and acetone for reasons of performance and availability. The test stand was designed to measure not only the power consumed to perform the conversion reaction but also the concentration of products formed after the reaction. The experimental tests showed that it was possible to perform the reactions at the voltages required for an efficient chemical looping heat pump. However, the tests also showed that the reactions proceed much slower than expected. To increase the rates of the reactions, an optimization effort on the membrane and catalyst selections was performed. </p> <p> </p> <p>Traditional catalyst materials used by solid polymer electrochemical cells, like those used in the testing, perform best in hydrated environments. The fluids isopropanol and acetone tend to displace water in the membranes, reducing the system conductivity. Multiple membrane types were explored for anhydrous operation. Reinforced sPEEK membranes were found to be the most suitable choice for compatibility with the CLHP working fluids. Multiple catalyst mixtures were also tested in the experimental setup. Density functional theory was used to develop a computational framework to develop activity maps which could predict the performance of catalyst materials based on calculated parameters. </p> <p> </p> <p>A detailed model of the CLHP electrochemical cell was developed. Built on open-source tools, the model was designed to determine the charge, mass, and heat transfers within the cell. The conversion of reactants along the channel of the cell as well as overall power consumption are predicted by the model. The model was validated against measurements and used to determine parameters for a CLHP cell that would have improved conversion performance and energy efficiency compared with the tested cell. </p> <p> </p> <p>The cell model was integrated into an overall system model which incorporates the effect of concentration changes throughout the entire cycle. Compared to the early-stage thermodynamic modeling, consideration of incomplete reactions provided more accurate predictions of the potential performance of CLHP systems. Different cell and system architectures were investigated to boost system performance. The model predictions demonstrated that the CLHP has the potential to provide high heat pumping efficiencies, but more work is still needed to improve the energy density of the system. </p>