Spelling suggestions: "subject:"beating - 1design anda construction"" "subject:"beating - 1design ando construction""
1 |
Modelling and evaluation of an energy efficient heating ventilation and air conditioning (HVAC) system in an office building15 January 2014 (has links)
M.Tech. (Architectural Technology) / It is estimated that commercial buildings are responsible for 5.4% of worldwide Green House Gas (GHG) emissions through their construction and on-going operation. In developed countries this figure can go up to 30%. The environmental control industry is one of the large consumers of this energy. Heating, ventilation and air conditioning (HVAC) contribute approximately 15% of South Africa's current peak electrical demand consumption according to Eskom (the South African electricity utility). The purpose of this dissertation is to analyse and evaluate methods to reduce the energy consumption of the HVAC system in a commercial office building. This encompasses careful building design to reduce heat loads and promote the circulation of fresh air; the use of energy-efficient air-conditioning systems and the incorporation of materials and technology to reduce energy consumption. This will be based upon a case study of the new SANRAL (South African National Roads Agency Limited) head office building in Val-DeGrace, Pretoria. A deductive research approach will be followed. The as-designed Actual Building is modelled with the appropriate energy modelling software and its annual energy usage is obtained. A benchmark based Notional Building complying with SANS 204:2008 criteria of the same size, shape, location and operational schedules as the Actual Building is also modelled and its energy usage results compared to that of the Actual Building. This comparison will determine how energy efficient the Actual Building's HVAC system is compared to a conventional Notional Building. Quantitative data collection is performed by empirical measurement of the energy usage of the as-built Actual Building. The raw data (power usageofthe HVAC system) is measured by Schneider Electric PM9c™ power meters located in the HVAC distribution boards of the building. This raw data are collected by Schneider Electric's ION Enterprise' power management software which has a user friendly interface from where the data can be downloaded. The power management software is connected to an ANDOVEWM Building Management System (BMS). Due to commissioning procedures and the timeframe at hand for the completion of this dissertation measurements could only be taken over a 7 month period. Operational data were measured from July 2011 to March 2012 thus accounting for summer, winter and a seasonal changeover period. The modelled energy usage results of the as-designed Actual Building are compared to the measured energy usage data obtained from the as-built Actual Building. This comparison serves to evaluate the accuracy of the software model...
|
2 |
Experimental and numerical investigation of noise generation from the expansion of high velocity HVAC flows on board ocean going fast ferriesNeale, James Richard, Mechanical & Manufacturing Engineering, Faculty of Engineering, UNSW January 2006 (has links)
This thesis details a study of strategies used to limit the flow generated noise encountered in the outlet diffusers of high velocity heating, ventilation and air conditioning (HVAC) duct systems. The underlying noise rating criterion is drawn from the specifications covering ocean going aluminium fast ferries. Although directed primarily towards the fast ferry industry the results presented herein are applicable to other niche high velocity HVAC applications. Experimental tests have been conducted to prove the viability of a high velocity HVAC duct system in meeting airflow requirements whilst maintaining acceptable passenger cabin noise levels. A 50 mm diameter circular jet of air was expanded using a primary conical diffuser with a variety of secondary outlet configurations. Noise measurements were taken across a velocity range of 15 to 60 m/s. An optimum outlet design has been experimentally identified by varying the diffuser angle, outlet duct length and the termination grill. A 4 to 5 fold reduction in required duct area was achieved with the use of a distribution velocity of 20 to 30 ms-1, without exceeding the prescribed passenger cabin noise criteria. The geometric configuration of the diffuser outlet assembly was found to have a pronounced effect on the noise spectrum radiating from the duct outlet. The development of a numerical model capable of predicting the flow induced noise generated by airflow exiting a ventilation duct is also documented. The model employs a Large Eddy Simulation (LES) CFD model to calculate the turbulent flow field through the duct diffuser section and outlet. The flow-generated noise is then calculated using a far field acoustic postprocessor based on the Ffowcs-Williams and Hawkings integral based formulation of Lighthill???s acoustic analogy. Time varying flow field variables are used to calculate the fluctuating noise sources located at the duct outlet and the resulting far field sound pressure levels. This result is then used to calculate the corresponding far field sound intensity and sound power levels. The numerical acoustic model has been verified and validated against the measured experimental results for multiple outlet diffuser configurations.
|
3 |
Experimental and numerical investigation of noise generation from the expansion of high velocity HVAC flows on board ocean going fast ferriesNeale, James Richard, Mechanical & Manufacturing Engineering, Faculty of Engineering, UNSW January 2006 (has links)
This thesis details a study of strategies used to limit the flow generated noise encountered in the outlet diffusers of high velocity heating, ventilation and air conditioning (HVAC) duct systems. The underlying noise rating criterion is drawn from the specifications covering ocean going aluminium fast ferries. Although directed primarily towards the fast ferry industry the results presented herein are applicable to other niche high velocity HVAC applications. Experimental tests have been conducted to prove the viability of a high velocity HVAC duct system in meeting airflow requirements whilst maintaining acceptable passenger cabin noise levels. A 50 mm diameter circular jet of air was expanded using a primary conical diffuser with a variety of secondary outlet configurations. Noise measurements were taken across a velocity range of 15 to 60 m/s. An optimum outlet design has been experimentally identified by varying the diffuser angle, outlet duct length and the termination grill. A 4 to 5 fold reduction in required duct area was achieved with the use of a distribution velocity of 20 to 30 ms-1, without exceeding the prescribed passenger cabin noise criteria. The geometric configuration of the diffuser outlet assembly was found to have a pronounced effect on the noise spectrum radiating from the duct outlet. The development of a numerical model capable of predicting the flow induced noise generated by airflow exiting a ventilation duct is also documented. The model employs a Large Eddy Simulation (LES) CFD model to calculate the turbulent flow field through the duct diffuser section and outlet. The flow-generated noise is then calculated using a far field acoustic postprocessor based on the Ffowcs-Williams and Hawkings integral based formulation of Lighthill???s acoustic analogy. Time varying flow field variables are used to calculate the fluctuating noise sources located at the duct outlet and the resulting far field sound pressure levels. This result is then used to calculate the corresponding far field sound intensity and sound power levels. The numerical acoustic model has been verified and validated against the measured experimental results for multiple outlet diffuser configurations.
|
Page generated in 0.2448 seconds