Thesis (M.S.)--University of Missouri-Columbia, 2003. / Typescript. Includes bibliographical references (leaves 50-51). Also available on the Internet.

Thesis (M.S.)--University of Missouri-Columbia, 2003. / Typescript. Includes bibliographical references (leaves 50-51). Also available on the Internet.

No description available.

Thesis (Ph. D.)--University of Texas at Austin, 2000. / Vita. Includes bibliographical references (leaves 181-194). Available also in a digital version from Dissertation Abstracts.

A series of physical and chemical analyses were conducted over a fifteen month period to establish the ecological risk, if any, of discharging minewater into aquatic ecosystems. Organic and inorganic analyses were used to determine the extent of contamination of minewater with soluble hydraulic fluids and other contaminant species. Throughout the sampling period the pithead discharge water exhibited a neutral pH and low levels of iron, manganese, zinc and potassium were found. Parallel toxicological and chemical studies identified elevated zinc levels above published toxicity levels for the test species Ceriodaphnia Dubia, but were not confirmed by subsequent study. The presence of organic species in the pit head discharge water was also identified, but the levels were found to be quite variable. Treatment processes involving the detention of the surface minewater and subsequent passage through wetlands exhibited a beneficial effect in reducing pollutant levels prior to disposal. Comparisons of the chemical composition of the minewater discharge with those of local waters were carried out and found to be similar in nature. / Master of Science (Hons)

This paper describes an investigation into the effects of fluid bulk modulus and traction coefficient properties on piston pump flow losses and radial pison motor torque losses through experimentation, modelling and simulation. Synthetic ester, high bulk modulus, multi-grade, and single grade mineral oils were evaluated. The high bulk modulus fluid exhibited 20% lower pump case and compensator flow losses than a conventional mineral oil of the same viscosity grade. Low traction coefficient fluids reduced the lowspeed torque losses of the radial piston motor by 50%. Physical models for pump case flow and motor torque losses were derived from the experimental data. Field data was collected from a hydraulically propelled agricultural machine. This data was used to model fluid performance in the machine. The simulation results predict that at an operating temperature of 80⁰C, optimizing the bulk modulus and traction coefficients of the fluid could reduce flow losses by 18% and torque losses by 5%. These findings demonstrate the potential of combining comprehensive fluid analysis with modeling and simulation to optimize fluids for the efficient transmission of power.

This paper describes an investigation into the effects of fluid bulk modulus and traction coefficient properties on piston pump flow losses and radial pison motor torque losses through experimentation, modelling and simulation. Synthetic ester, high bulk modulus, multi-grade, and single grade mineral oils were evaluated. The high bulk modulus fluid exhibited 20% lower pump case and compensator flow losses than a conventional mineral oil of the same viscosity grade. Low traction coefficient fluids reduced the lowspeed torque losses of the radial piston motor by 50%. Physical models for pump case flow and motor torque losses were derived from the experimental data. Field data was collected from a hydraulically propelled agricultural machine. This data was used to model fluid performance in the machine. The simulation results predict that at an operating temperature of 80⁰C, optimizing the bulk modulus and traction coefficients of the fluid could reduce flow losses by 18% and torque losses by 5%. These findings demonstrate the potential of combining comprehensive fluid analysis with modeling and simulation to optimize fluids for the efficient transmission of power.

Thesis (M.Sc. (Hons))--University of Western Sydney, 2001. / "A thesis presented for the Degree of Master of Science (Honours), Centre for Electrochemical Research and Analytical Technology, School of Science, Food and Horticulture, University of Western Sydney, March 2001." Bibliography: leaves 62-67.

The paper describes the comparison and the difference of modern hydraulic fluids compared to conventional hydraulic fluids. A comparison of different base oil groups, solvent neutrals, group I and comparison with hydrotreated/hydroprocessed group II and/or group III base oils is presented. The influence on oxidation stability, elastomer compatibility, carbon distribution and physical properties is outlined.

Cavitation is the spontaneous vaporisation of a liquid to its gaseous state due to the local absolute pressure falling to the liquid's vapour pressure (Douglas, Gasiorek et al. 1995). Cavitation is present in a wide range of mechanical systems ranging from ship screws to journal bearing. Generally, cavitation is unavoidable and may cause considerable damage and efficiency losses to these systems. This thesis considers hydraulic systems specifically, and uses a modified Greens equation to develop a boundary integral method to simulate the effect that suspended solid bodies have on a single cavitation bubble. Because of the limitations of accurately modelling cavitation bubbles beyond touchdown, results are only presented for cases up to touchdown. The aim of the model is to draw insight into the reasons there is a measurable change in cavitation erosion rate with increasing oil-in-water emulsion percentage. This principle was extended to include the effect that ingested particulates may have on cavitation in hydraulic machinery. Two particular situations are modelled; the first consists of stationary rigid particles in varying proximity to a cavitation bubble near a rigid boundary. The second case is similar; however the suspended particle is allowed to move under the influence of the pressure differential caused by the expanding/contracting cavitation bubble. Numerous characteristics of the domain are considered, including domain pressures and fluid field motion, and individual boundary surface characteristics. The conclusion of the thesis is that solid bodies, either stationary or moving, have little effect on the cavity from an energy perspective. Regardless of size or density, all energy transferred from the cavity to the solid body is returned indicating that there is no net change. As this energy is ultimately responsible for the peak pressure experienced by the domain (and hence responsible for eroding the rigid boundary) as the cavity rebounds, it then serves that a cavity with a solid body will rebound at the same pressure as a cavity without a suspended body present. If this is coupled with the observation that the cavity centroid at touchdown is largely unaffected by the presence of a suspension, then it would appear that the bubble near a solid would rebound at a very similar position as a cavity without a solid. Consequently, the damage potential of a cavity is unaffected by a suspension. However, there is one point of contention as the profile of the re-entrant jet of the cavity is altered by the presence of a suspension. As energy is radiated away from the cavity during penetration, it is possible that the shape of the jet may alter the rate that energy is radiated away during penetration. However, this requires further research to be definitive.