Spelling suggestions: "subject:"hysteresis model"" "subject:"hysteresis godel""
1 |
An Iron Loss Estimation Process Supported by Modularized Iron Loss Datasheets of Electromagnetic Steel for Switched-Reluctance MachineHsu, Yu-Wei 06 September 2010 (has links)
The objective of this thesis is to provide a quick process to estimate iron losses of the electric machines with various structures that employ electromagnetic steels in their designs. Due to non-uniform distributed operational magnetic flux densities resulted from the machine structures, the iron losses of machines can not be properly estimated. The aim of the scheme is to modify the deviations among the measurements and the calculations. At first, several standardized steel modules that can be used to assemble the machine structures are established, then a test-bed with closed magnetic path to supply operational magnetic field inside those electric machines is constructed. To calculate the iron loss of each module, the averaged flux densities for each area of the module are measured by needle probe method, and the corresponding magnetic field intensities are calculated from Jiles and Atherton (J-A) model hysteresis model. Finally, the iron loss datasheets for each module are constructed by these measurements, and the iron losses of machines are estimated through assembling the modules. In this thesis, a switched-reluctance machine (SRM) is selected for assessment comparisons, and its iron loss can be calculated through datasheets according to the machine structure. It is believed that the findings of this study can provide a valuable reference and a reliable process in motor designing and manufacturing.
|
2 |
Nonlinear Control of Magnetic SignaturesNiemoczynski, Bogdan January 2015 (has links)
Magnetic properties of ferrite structures are known to cause fluctuations in Earth's magnetic field around the object. These fluctuations are known as the object's magnetic signature and are unique based on the object's geometry and material. It is a common practice to neutralize magnetic signatures periodically after certain time intervals, however there is a growing interest to develop real time degaussing systems for various applications. Development of real time degaussing system is a challenging problem because of magnetic hysteresis and difficulties in measurement or estimation of near-field flux data. The goal of this research is to develop a real time feedback control system that can be used to minimize magnetic signatures for ferrite structures. Experimental work on controlling the magnetic signature of a cylindrical steel shell structure with a magnetic disturbance provided evidence that the control process substantially increased the interior magnetic flux. This means near field estimation using interior sensor data is likely to be inaccurate. Follow up numerical work for rectangular and cylindrical cross sections investigated variations in shell wall flux density under a variety of ambient excitation and applied disturbances. Results showed magnetic disturbances could corrupt interior sensor data and magnetic shielding due to the shell walls makes the interior very sensitive to noise. The magnetic flux inside the shell wall showed little variation due to inner disturbances and its high base value makes it less susceptible to noise. This research proceeds to describe a nonlinear controller to use the shell wall data as an input. A nonlinear plant model of magnetics is developed using a constant to represent domain rotation lag and a gain function to describe the magnetic hysteresis curve for the shell wall. The model is justified by producing hysteresis curves for multiple materials, matching experimental data using a particle swarm algorithm, and observing frequency effects. The plant model is used in a feedback controller and simulated for different materials as a proof of concept. / Electrical and Computer Engineering
|
3 |
Simulated Response of Degrading Hysteretic Joints With Slack BehaviorHeine, Christian P. 15 August 2001 (has links)
A novel, general, numerical model is described that is capable of predicting the load-displacement relationship up to and at failure of multiple-bolt joints in timber of various configurations. The model is not tied to a single input function and bolt holes are permitted to be drilled oversize resulting in a slack system.
The model consists of five parts. A new mathematical hysteresis model describes the stiffness of the individual bolt at each time step increment and accounts for non-linear and slack behavior; a mechanically-based structural stiffness model explains the interaction of one bolt with another bolt within a joint; an analytically-based failure model computes the stresses at each time step and initiates failure if crack length equals fastener spacing; a stochastic routine accounts for material property variation; and a heuristic optimization routine estimates the parameters needed.
The core model is a modified array of differential equations whose solution describes accurate hysteresis shapes for slack systems. Hysteresis parameter identification is carried out by a genetic algorithm routine that searches for the best-fit parameters following evolutionary principles (survival of the fittest). The structural model is a linear spring model. Failure is predicted based on a newly developed 'Displaced-Volume-Method' in conjunction with beam on elastic foundation theory, elastic theory, and a modified Tsai-Wu Failure criterion.
The devised computer model enhances the understanding of the mechanics of multiple-bolt joints in timber, and yields valid predictions of joint response of two-member multiple-bolt joints. This research represents a significant step towards the simulation of structural wood components. / Ph. D.
|
4 |
A non-linear dynamic macroelement for soil structure interaction analyses of piles in liquefiable sitesVarun 01 July 2010 (has links)
A macroelement is developed for soil-structure interaction analyses of piles in liquefiable soils, which captures efficiently the fundamental mechanisms of saturated granular soil behavior. The mechanical model comprises a nonlinear Winkler-type model that accounts for soil resistance acting along the circumference of the pile, and a coupled viscous damper that simulates changes in radiation damping with increasing material non-linearity. Three-dimensional (3D) finite element (FE) simulations are conducted for a pile in radially homogeneous soil to identify the critical parameters governing the response. The identified parameters, i.e., hydraulic conductivity, loading rate of dynamic loading, dilation angle and liquefaction potential are then expressed in dimensionless form.
Next, the macroelement parameters are calibrated as a function of the soil properties and the effective stress. A semi-empirical approach that accounts for the effects of soil-structure interaction on pore pressure generation in the vicinity of pile is used to detect the onset of liquefaction. The predictions are compared with field data obtained using blast induced liquefaction and centrifuge tests and found to be in good agreement.
Finally, the macroelement formulation is extended to account for coupling in both lateral directions. FEM simulations indicate that response assuming no coupling between the two horizontal directions for biaxial loading tends to overestimate the soil resistance and fails to capture features like 'apparent negative stiffness', 'strain hardening' and 'rounded corners'.
|
5 |
Simulation numérique des transferts de chaleur et d’humidité dans une paroi multicouche de bâtiment en matériaux biosourcés / Numerical simulation of heat and moisture transfers in a building multi-layer wall made of bio-based materialsLelièvre, Dylan 08 January 2015 (has links)
Dans un contexte de performance énergétique et de durabilité dans le secteur du bâtiment, la maîtrise du comportement hygrothermique des matériaux d'enveloppe, notamment hygroscopiques, est essentielle. Les travaux réalisés concernent la compréhension et la modélisation des transferts de chaleur et d'humidité au sein d'une paroi multicouche de bâtiment composée de matériaux biosourcés.Une attention particulière est portée sur les phénomènes d'hystérésis observés sur les isothermes de sorption. Un modèle numérique 1D développé sur COMSOL Multiphysics est exploité pour simuler en régime transitoire les champs de température et de pression de vapeur dans trois situations. La première concerne l'étude du comportement hygrothermique de matériaux fortement hygroscopique (béton de chanvre) et faiblement hygroscopiques (enduits à base de chaux) soumis à diverses variations cycliques d'humidité relative. Un bon accord est constaté entre les simulations et des mesures d'humidité relative, de température et de teneur en eau. Néanmoins, les résultats présentent une forte sensibilité aux propriétés hydriques. Dans un second temps, une étude est menée sur une paroi de béton de chanvre instrumentée placée dans une enceinte bi-climatique et exposée à des variations de température et d'humidité relative. La confrontation des évolutions mesurées et calculées montre la nécessité de bien définir le champ de teneur en eau initiale. La dernière étude concerne une paroi multicouche (béton de chanvre et enduits). Il apparaît que les enduits jouent un rôle important sur le comportement de la paroi et il est nécessaire de prendre en compte l'influence de la température sur les courbes de sorption. / In a context of energy efficiency and durability in the field of building, the understanding of hygrothermal behaviour of building materials, especially hygroscopic ones, is essential. This study aim to understand and model heat and moisture transfers in a multi-layer building wall made of biosourced materials. We focus in particular on hysteretic phenomena observed on sorption isotherms. A one-dimensional numerical model developed with the COMSOL Multiphysics software is used to simulate transient temperature and vapour pressure in three situations. The first one is about the hygrothermal behaviour of materials, highly hygroscopic (hemp concrete) and lowly hygroscopic (lime-based plasters), exposed to several cyclical variations of relative humidity. A good agreement is observed between simulated and measured values of relative humidity, temperature and moisture content. However, results are highly sensitive to hydric properties. Then, a study is performed on an instrumented hemp-concrete wall built in a bi-climatic chamber and exposed to simultaneous temperature and relative humidity variations. The confrontation between measured and simulated values shows the importance of initial moisture content.
|
6 |
Energy Based Seismic Performance Assessment Of Reinforced Concrete ColumnsAcun, Bora 01 March 2010 (has links) (PDF)
Severe seismic events in urban regions during the last two decades revealed that the structures constructed before the development of modern seismic codes are the most vulnerable to earthquakes. Sub-standard reinforced concrete buildings constitute an important part of this highly vulnerable urban building stock. There is urgent need for the development and improvement of methods for seismic performance assessment of existing reinforced concrete structures.
As an alternative to current conventional force-based assessment methods, a performance evaluation procedure for structural members, mainly reinforced concrete columns is proposed in this study, by using an energy-based approach combined with the low cycle fatigue concept. An energy-based hysteresis model is further introduced for representing the inelastic response of column members under severe seismic excitations. The shape of the hysteresis loops are controlled by the dissipated cumulative energy whereas the ultimate strength is governed by the low cycle fatigue behavior. These two basic characteristics are obtained experimentally from full scale specimens tested under constant and variable amplitude
displacement cycles.
The first phase of the experimental program presented in the study constitutes of testing sub-standard non-conforming column specimens. The second phase of testing was conducted on standard, code compliant reinforced concrete columns. A
total number of 13 specimens were tested. The behavior of these specimens was observed individually and comparatively according to the performance based objectives. The results obtained from the experiments were employed for developing relations between the energy dissipation capacity of specimens, the specimen properties as well as the imposed displacement history. Moreover, the measured rotation capacities at the plastic regions are evaluated comparatively with the limits proposed by modern displacement-based seismic design and assessment provisions.
|
7 |
Design of a State of Charge (SOC) Estimation Block for a Battery Management System (BMS). / Entwicklung eines Ladezustand Block für Battery Management System (BMS)Cheema, Umer Ali January 2013 (has links)
Battery Management System (BMS) is an essential part in battery powered applications where large battery packs are in use. BMS ensures protection, controlling, supervision and accurate state estimation of battery pack to provide efficient energy management. However the particular application determines the accuracy and requirements of BMS where it has to implement; in electric vehicles (EVs) accuracy cannot be compromised. The software part of BMS estimates the states of the battery pack and takes the best possible decision. In EVs one of the key tasks of BMS’s software part is to provide the actual state of charge (SOC), which represents a crucial parameter to be determined, especially in lithium iron phosphate (LiFePO4) batteries, due to the presence of the high hysteresis behavior in the open circuit voltage than other kind of lithium batteries. This hysteresis phenomena appears with two different voltage curves during the charging and discharging process. The value of the voltage that the battery is going to assume during the off-loading operation depends on several factors, such as temperature, loop direction and ageing. In this research work, hybrid method is implemented in which advantages of several methods are achieved by implementing one technique combined with another. In this work SOC is calculated from coulomb counting method and in order to correct the error of SOC, an hysteresis model is developed and used due to presence of hysteresis effect in LiFePO4 batteries. An hysteresis model of the open circuit voltage (OCV) for a LiFePO4 cell is developed and implemented in MATLAB/Simulink© in order to reproduce the voltage response of the battery when no current from the cell is required (no load condition). Then the difference of estimated voltage and measured voltage is taken in order to correct the error of SOC calculated from coulomb counting or current integration method. To develop the hysteresis model which can reproduce the same voltage behavior, lot of experiments have been carried out practically in order to see the hysteresis voltage response and to see that how voltage curve change with the variation of temperature, ageing and loop direction. At the end model is validated with different driving profiles at different ambient temperatures.
|
8 |
Minimisation des pertes fer des machines électriques de traction par la modélisation et l'optimisation / Minimization of iron loss of traction electrical motors by modeling and optimization systemsFrias, Anthony 12 March 2015 (has links)
Le coût, l'autonomie et la durée de vie sont les principaux aspects qui freine le public dans l'achat d'une voiture électrique. Tous ces aspects sont liés à la batterie qui ne permet de stocker qu'une quantité limitée d'énergie. Dans ces conditions, il est indispensable de maîtriser les pertes d'énergie de la chaîne de traction. La machine électrique étant le principal consommateur d'énergie, elle joue un rôle important dans l'efficacité énergétique globale. Dans ce contexte, comment réduire les pertes de la machine électrique pour la rendre plus efficace ? Pour répondre à cette question, l'objectif de ce travail est de modéliser (avec une précision suffisante) et réduire les pertes fer dans notre application machine électrique de traction afin de les maîtriser. On comblera ainsi le manque de confiance en les modèles de pertes fer que peut avoir le concepteur de machine du concepteur de machine en lui permettant de réaliser des optimisations fines jusque dans les dernières phases de développement. Dans la première partie de ce manuscrit, le lecteur découvrira alors une machine synchrone à rotor bobiné du point de vue du matériau magnétique doux. Les premières conclusions montrent qu'une modélisation fine est nécessaire pour bien prendre en compte les phénomènes générateurs de pertes. On s'intéresse également à la mesure des matériaux magnétiques doux afin de comprendre de manière générale et tangible les pertes dans le matériau. On prend également conscience de la toute première source d'incertitude des modèles, la mesure du matériau. Enfin, nous présentons les démarches couramment rencontrées dans la littérature pour la modélisation des pertes fer. Face aux limitations des modèles couramment rencontrés, le modèle LS (un modèle d'hystérésis scalaire qui décompose les pertes en une contribution statique et une contribution dynamique) est redéveloppé afin qu'il réponde encore mieux aux exigences de l'industrie automobile. Il est précis et facilement identifiable à partir de mesures faciles à réaliser. La contribution statique reprend le modèle de Preisach formulé à l'aide des fonctions d'Everett dont l'identification à partir des caractéristiques mesurées est directe. La contribution dynamique quant à elle est dorénavant identifiable à partir de caractérisations en induction sinusoïdales. La précision du modèle ainsi améliorée est ensuite validée sur 63 cas tests exigeants dont la forme de l'induction est à fort contenus harmoniques. Le modèle développé est ensuite couplé avec un modèle électromagnétique élément finis de la machine électrique et validé par l'expérience. Les mesures faites sur le matériau étant l'un des points faibles des modèles, une méthodologie permettant d'évaluer la pertinence de la plage des mesures est proposée. On dresse également un état de l'art de l'impact du process (découpage, empilement et assemblage des tôles) sur les pertes fer afin d'aider le concepteur à mettre en balance les impacts liés au process qui n'ont pu être modélisés. Enfin des méthodologies parmi lesquels, les méthodologies des plans d'expériences sont mises en place afin d'optimiser les cartographies de commandes en des temps de calcul raisonnables. On montre des gains allant jusqu'à 50% de réduction des pertes totales de la machine dans certaines zones de fonctionnement par rapport à une optimisation dont l'objectif serait de minimiser uniquement les pertes dans les conducteurs de la machine. Ces résultats montrent l'intérêt d'utiliser un modèle de pertes fer précis afin de réduire les pertes totales de la machine. / Cost, range and lifetime are the main aspects that hold back the consumer to buy electric cars. These three aspects are all related to the battery which stores a limited amount of energy. Under such condition energy consumption is a major concern in electric cars. As the major electricity consumer, electrical machines play a key role for global energy savings. In this context how the electric machine can be made more energy efficient? To answer this question this thesis aim to model (accurately enough) and reduce the iron losses in traction electrical machine for electrical car. Indeed iron loss model suffer from a lack of confidence when it comes to fine optimization during the late phase of development. This thesis answers this question and takes into account the development criteria of the car industry and the constraints of the electric car. The first part of the thesis gives an overview of the application by taking a wounded rotor synchronous machine as a case study. The reader will discover the electrical machine with a soft magnetic material perspective. First, conclusion show that fine modelling of the electric machine is necessary to achieve desired accuracy. An overview on soft magnetic material behavior and measurements is then given. The reader will then acquire a broad feeling on soft magnetic material behavior and understands the first source of inaccuracy of the models (the measurements). Then, the typical models for predicting iron losses in magnetic materials are presented in a literature review. The second part of this study focus on iron loss modelling aspect. The loss surface model (a scalar hysteresis model made of a static and dynamic contribution) is used as the base of this modelling work. The static contribution is re-developed using Everett function formulation of the Preisach model is used to allow easy identification of the model directly from measurements. The identification of the dynamic contribution is re-worked to allow identification from sine-wave measurements (triangular wave measurement previously required). The model accuracy is improved and validated on 63 test cases with high harmonic distortion wave forms. The iron loss model is then coupled to finite element model of the electric machine and the limits of the model are investigated. One of the limits coming from measurement limitation, a methodology to evaluate the relevance of the measurement range is proposed. A literature review of the main impact of the process including cutting, stacking and assembling effects on electrical steel magnetic characteristics is intended to complement the modelling work to help the decision making of the designer on aspects that cannot be modeled. Finally methodologies playing with the modelling hypothesis and involving design of experiment and response surface are presented to reduce computational time and allow the optimization of the control of the machine. The optimizations carried out show total machine loss reduction up to 50% for some working point of the machine compared to an optimization dedicated to minimize only Joule's losses. This results show the interest of using a reliable iron loss model to reduce the total loss of the machine.
|
9 |
Etude et mise au point d'une nouvelle famille d'alterno-démarreur pour véhicules hybrides et électriques / Study and development of a new family of stater-generator for hybrid and electric vehiclesLi, Li 19 May 2011 (has links)
Les travaux de cette thèse portent sur une nouvelle structure de machine à double excitation (MSDE) pour l'application des véhicules hybrides et électriques. Ce type de machine, ayant deux sources d'excitation, bénéficie un degré de liberté supplémentaire et un contrôle facile sur le flux. Grâce à ce degré de liberté, la machine peut être dimensionnée de manière que son meilleur rendement coïncide avec la zone de fonctionnement la plus sollicitée de la machine. Cette nouvelle structure a fait l'objet principal de ce mémoire. Le fonctionnement de la MSDE est présenté dans les deux premiers chapitres. La machine est dimensionnée suivant un cahier des charges pour véhicule hybride. La validation expérimentale a confirmé le bon fonctionnement de la structure et montré son intérêt. Une autre problématique dans le dimensionnement de la machine est l'aspect thermique car les machines sont devenues de plus en plus compactes et puissantes. Une estimation correcte des pertes est indispensable pour évaluer correctement les performances de la machine. C'est la raison pour laquelle on a décidé de consacrer une partie de cette thèse à la modélisation des pertes fer, dont l'estimation n'est pas évidente. / The PhD work deals with a new structure of hybrid excited synchronous machine (MSDE) for the application of hybrid and electric vehicles. This kind of machine, with two excitation sources, benefits an additional degree of freedom and an easy control of flux. Due to this degree of freedom, the machine can be designed in the way that its best efficiency coincide with the most solicited operating zone. This new machine structure is the main subject of this study. The principle of this MSDE is presented in the first two chapters. The machine is then designed according to the specifications for an hybrid vehicle. The experimental validation has confirmed the proper functioning of the structure and shown its interest. Another important subject in the machine sizing is the thermal aspect because our machines are becoming more and more compact and powerful. A correct estimation of the iron loss is essential for evaluating correctly the machine performances. That's why we have decided to dedicate a part of this study to the modeling of iron loss, of which the estimation is not evident.
|
Page generated in 0.0924 seconds