In the framework of the micro-CHP (Combined Heat and Power) energy systems and the Distributed Generation (GD) concept, an Integrated Energy System (IES) able to meet the energy and thermal requirements of specific users, using different types of fuel to feed several micro-CHP energy sources, with the integration of electric generators of renewable energy sources (RES), electrical and thermal storage systems and the control system was conceived and built. A 5 kWel Polymer Electrolyte Membrane Fuel Cell (PEMFC) has been studied. Using experimental data obtained from various measurement campaign, the electrical and CHP PEMFC system performance have been determinate. The analysis of the effect of the water management of the anodic exhaust at variable FC loads has been carried out, and the purge process programming logic was optimized, leading also to the determination of the optimal flooding times by varying the AC FC power delivered by the cell. Furthermore, the degradation mechanisms of the PEMFC system, in particular due to the flooding of the anodic side, have been assessed using an algorithm that considers the FC like a black box, and it is able to determine the amount of not-reacted H2 and, therefore, the causes which produce that. Using experimental data that cover a two-year time span, the ageing suffered by the FC system has been tested and analyzed.

La regolazione dei sistemi di propulsione a razzo a propellente solido (Solid Rocket Motors) ha da sempre rappresentato una delle principali problematiche legate a questa tipologia di motori. L’assenza di un qualsiasi genere di controllo diretto del processo di combustione del grano solido, fa si che la previsione della balistica interna rappresenti da sempre il principale strumento utilizzato sia per definire in fase di progetto la configurazione ottimale del motore, sia per analizzare le eventuali anomalie riscontrate in ambito sperimentale. Variazioni locali nella struttura del propellente, difettosità interne o eterogeneità nelle condizioni di camera posso dare origine ad alterazioni del rateo locale di combustione del propellente e conseguentemente a profili di pressione e di spinta sperimentali differenti da quelli previsti per via teorica. Molti dei codici attualmente in uso offrono un approccio piuttosto semplificato al problema, facendo per lo più ricorso a fattori correttivi (fattori HUMP) semi-empirici, senza tuttavia andare a ricostruire in maniera più realistica le eterogeneità di prestazione del propellente. Questo lavoro di tesi vuole dunque proporre un nuovo approccio alla previsione numerica delle prestazioni dei sistemi a propellente solido, attraverso la realizzazione di un nuovo codice di simulazione, denominato ROBOOST (ROcket BOOst Simulation Tool). Richiamando concetti e techiche proprie della Computer Grafica, questo nuovo codice è in grado di ricostruire in processo di regressione superficiale del grano in maniera puntuale, attraverso l’utilizzo di una mesh triangolare mobile. Variazioni locali del rateo di combustione posso quindi essere facilmente riprodotte ed il calcolo della balistica interna avviene mediante l’accoppiamento di un modello 0D non-stazionario e di uno 1D quasi-stazionario. L’attività è stata svolta in collaborazione con l’azienda Avio Space Division e il nuovo codice è stato implementato con successo sul motore Zefiro 9. / The regulation of propulsive performance in solid rocket motors is one of the biggest difficulties related to this type of space systems. The absence of any direct mechanism for controlling the combustion of solid propellant makes the prevision of internal ballistics the main tool adopted not only in defining grain configuration but also in reconstructing burning rate anisotropies. Local variations in grain composition, heterogeneities or surface imperfections can generate unexpected alterations in pressure profiles and consequently in thrust performance. Most of recent models propose a simplified approach to the problem, by using semi-empirical corrective functions known as HUMP factors which, however, cannot fully describe the spatial anisotropies inside the propellant volume. This work aims to present a new approach to the numerical prevision of SRMs performances and a new simulation code, named ROBOOST (Rocket Boost Simulation Tool), has been developed at that regard. Borrowing concepts and techniques from Computer Graphics, the code is able to reproduce the burning surface regression in a Lagrangian way, using a moving discrete triangle mesh to describe the grain volume. Spatial heterogeneities in local burn-rate values can be easily implemented and the solution of the chamber fluid-dynamics is achieved by coupling a 0D unsteady internal ballistic model and a 1D quasi-steady one. The activity has been carried on in collaboration with the Avio Space Division company and the new code has been successfully tested on the Zefiro 9 SRM. In parallel, a numerical analysis of solid propellant burning characteristics has been undertaken, in order to evaluate all possible conditioning elements and to implement them within simulation runs.

Il lavoro di Dottorato si è incentrato con successo sullo studio della possibilità di applicare il modello ADM1 per la descrizione e verifica di impianti industriali di digestione anaerobica. Dai dati sperimentali il modello e l'implementazione in software di analisi numerica si sono rivelati strumenti efficaci. Il software sviluppato è stato utilizzato come strumento di progettazione di impianti alimentati con biomasse innovative, analizzate con metodiche biochimiche (BMP) in scala di laboratorio. Lo studio è stato corredato con lo studio di fattibilità di un impianto reale con verifica di ottimo economico. / This work of thesis succesfully studied the feasibility of ADM1 application to Anaerobic Digestion industrial biogas plant description. The model and its implementation in numerical analysis software is an efficient tool. The software was applied to new substrates tested in bench scale tests (BMP tests) to design innovative AD bioreactors on industrial scale. This study also features the feasibility study of an existing industrial biogas plant, completed with the economic study (business plan).

Nel panorama motoristico ed automobilistico moderno lo sviluppo di motori a combustione interna e veicoli è fortemente influenzato da diverse esigenze che spesso sono in contrasto le une con le altre. Infatti gli obiettivi di economicità e riduzione dei costi riguardanti la produzione e la commercializzazione dei prodotti sono in contrasto con gli sforzi che devono essere operati dalle case produttrici per soddisfare le sempre più stringenti normative riguardanti le emissioni inquinanti ed i consumi di carburante dei veicoli. Fra le numerose soluzioni presenti i veicoli ibridi rappresentano una alternativa che allo stato attuale è già presente sul mercato in varie forme, a seconda della tipologie di energie accoppiate. In letteratura è possibile trovare numerosi studi che trattano l’ottimizzazione dei componenti o delle strategie di controllo di queste tipologie di veicoli: in moltissimi casi l’obiettivo è quello di minimizzare consumi ed emissioni inquinanti. Normalmente non viene posta particolare attenzione agli effetti che l’aggiunta delle macchine elettriche e dei componenti necessari per il funzionamento delle stesse hanno sulla dinamica del veicolo. Il presente lavoro di tesi è incentrato su questi aspetti: si è considerata la tipologia di veicoli ibridi termici-elettrici di tipo parallelo andando ad analizzare come cambiasse il comportamento dinamico del veicolo in funzione del tipo di installazione considerato per la parte elettrica del powertrain. In primo luogo è stato quindi necessario costruire ed implementare un modello dinamico di veicolo che permettesse di applicare coppie alle quattro ruote in maniera indipendente per considerare diverse tipologie di powertrain. In seguito si sono analizzate le differenze di comportamento dinamico fra il veicolo considerato e l’equivalente versione ibrida e i possibili utilizzi delle macchine elettriche per correggere eventuali deterioramenti o cambiamenti indesiderati nelle prestazioni del veicolo. / One of the challenges of the modern automotive industry is to develop engines and vehicles with an always more stringent legislation about pollutant emissions. Hybrid vehicles are a valid alternative to these limitations and could represent a good way to reduce fuel consumption and pollutant emissions. In literature it is possible to find several studies that deal with the optimization of the components or of the control strategies of this kind of vehicles, but less importance is given to the effects on vehicle dynamics that could be caused by the addition of the components of the additional system. The idea behind this work is to add on a traditional vehicle an electric kit, composed by 2 electric motors that can be added in correspondence of the non-driven wheels, a battery and the necessary power electronics to control the 2 motors obtaining an hybrid vehicle: the attention will be focused on vehicle dynamics and in particular on the changes in vehicle dynamics due to the mass increase and to the variation of the center of gravity position. Moreover it will be investigated how to use the electric motors to correct undesired effects in vehicle behavior. To achieve the preset objectives, a 14 degrees freedom vehicle model, which could allow to apply a different torque to each wheel, has been developed in Matlab/Simulink environment and validated. The so-built simulator has then been used to simulate 2 configurations of the same vehicle (with different mass and center of gravity position) to compare their performances and to verify which effects on vehicle dynamics could be obtained applying driving and braking torques through the electric motors.

La tesi affronta il concetto di esposizione al rischio occupazionale e il suo scopo è quello di indagare l’ambiente di lavoro e il comportamento dei lavoratori, con l'obiettivo di ridurre il tasso di incidenza degli infortuni sul lavoro ed eseguire la riduzione dei rischi. In primo luogo, è proposta una nuova metodologia denominata MIMOSA (Methodology for the Implementation and Monitoring of Occupational SAfety), che quantifica il livello di "salute e sicurezza" di una qualsiasi impresa. Al fine di raggiungere l’obiettivo si è reso necessario un approccio multidisciplinare in cui concetti d’ingegneria e di psicologia sono stati combinati per sviluppare una metodologia di previsione degli incidenti e di miglioramento della sicurezza sul lavoro. I risultati della sperimentazione di MIMOSA hanno spinto all'uso della Logica Fuzzy nel settore della sicurezza occupazionale per migliorare la metodologia stessa e per superare i problemi riscontrati nell’incertezza della raccolta dei dati. La letteratura mostra che i fattori umani, la percezione del rischio e il comportamento dei lavoratori in relazione al rischio percepito, hanno un ruolo molto importante nella comparsa degli incidenti. Questa considerazione ha portato ad un nuovo approccio e ad una seconda metodologia che consiste nella prevenzione di incidenti, non solo sulla base dell'analisi delle loro dinamiche passate. Infatti la metodologia considera la valutazione di un indice basato sui comportamenti proattivi dei lavoratori e sui danni potenziali degli eventi incidentali evitati. L'innovazione consiste nell'applicazione della Logica Fuzzy per tener conto dell’"indeterminatezza" del comportamento umano e del suo linguaggio naturale. In particolare l’applicazione è incentrata sulla proattività dei lavoratori e si prefigge di impedire l'evento "infortunio", grazie alla generazione di una sorta d’indicatore di anticipo. Questa procedura è stata testata su un’azienda petrolchimica italiana. / The thesis deals with the topic of occupational risk exposure and its purpose is to investigate the workplace and the workers behaviors with the aim to reduce the rate of occurrence of occupational accidents thus achieving also risk reduction. First, a new methodology, named MIMOSA (Methodology for the Implementation and Monitoring of Occupational SAfety), which quantifies the “health and safety”, is proposed. In order to achieve this goal a multidisciplinary approach was required and thus in this study engineering and psychology were combined to develop a predictive methodology for the improvement of the assessment of occupational safety. The results of MIMOSA experimentation led to the use of Fuzzy Logic in the field of occupational safety because this mathematical method has the capability both to improve the Mimosa methodology and to overcome the problems related to the uncertainty present in the collected data. The literature shows that human factors, risk perception and workers behavior in relation to the perceived risk, play a very important role in injury occurrence. This consideration led to a new approach and a second fuzzy-based methodology is proposed, which consists in an effective prevention of accidents not only on the basis of the analysis of their past dynamics. Indeed the methodology considers the evaluation of an index, a rewarding index not necessarily related to monetary incentive, on the basis of proactive behavior of workers and of potential damages of accidental events that have been avoided. The innovation also consists in the application of a fuzzy logic tool in order to take into account the typical “vagueness” of human behavior and of its natural language. In particular since this application is focused on workers' proactivity, it has the aim of preventing the event "injury", thus the generated index is a kind of leading indicator.

Wearable inertial and magnetic measurements units (IMMU) are an important tool for underwater motion analysis because they are swimmer-centric, they require only simple measurement set-up and they provide the performance results very quickly. In order to estimate 3D joint kinematics during motion, protocols were developed to transpose the IMMU orientation estimation to a biomechanical model. The aim of the thesis was to validate a protocol originally propositioned to estimate the joint angles of the upper limbs during one-degree-of-freedom movements in dry settings and herein modified to perform 3D kinematics analysis of shoulders, elbows and wrists during swimming. Eight high-level swimmers were assessed in the laboratory by means of an IMMU while simulating the front crawl and breaststroke movements. A stereo-photogrammetric system (SPS) was used as reference. The joint angles (in degrees) of the shoulders (flexion-extension, abduction-adduction and internal-external rotation), the elbows (flexion-extension and pronation-supination), and the wrists (flexion-extension and radial-ulnar deviation) were estimated with the two systems and compared by means of root mean square errors (RMSE), relative RMSE, Pearson’s product-moment coefficient correlation (R) and coefficient of multiple correlation (CMC). Subsequently, the athletes were assessed during pool swimming trials through the IMMU. Considering both swim styles and all joint degrees of freedom modeled, the comparison between the IMMU and the SPS showed median values of RMSE lower than 8°, representing 10% of overall joint range of motion, high median values of CMC (0.97) and R (0.96). These findings suggest that the protocol accurately estimated the 3D orientation of the shoulders, elbows and wrists joint during swimming with accuracy adequate for the purposes of research. In conclusion, the proposed method to evaluate the 3D joint kinematics through IMMU was revealed to be a useful tool for both sport and clinical contexts.

Flow features inside centrifugal compressor stages are very complicated to simulate with numerical tools due to the highly complex geometry and varying gas conditions all across the machine. For this reason, a big effort is currently being made to increase the fidelity of the numerical models during the design and validation phases. Computational Fluid Dynamics (CFD) plays an increasing role in the assessment of the performance prediction of centrifugal compressor stages. Historically, CFD was considered reliable for performance prediction on a qualitatively level, whereas tests were necessary to predict compressors performance on a quantitatively basis. In fact "standard" CFD with only the flow-path and blades included into the computational domain is known to be weak in capturing efficiency level and operating range accurately due to the under-estimation of losses and the lack of secondary flows modeling. This research project aims to fill the gap in accuracy between "standard" CFD and tests data by including a high fidelity reproduction of the gas domain and the use of advanced numerical models and tools introduced in the author's OEM in-house CFD code. In other words, this thesis describes a methodology by which virtual tests can be conducted on single stages and multistage centrifugal compressors in a similar fashion to a typical rig test that guarantee end users to operate machines with a confidence level not achievable before. Furthermore, the new "high fidelity" approach allowed understanding flow phenomena not fully captured before, increasing aerodynamicists capability and confidence in designing high efficiency and high reliable centrifugal compressor stages.

Traditionally, the study of internal combustion engines operation has focused on the steady-state performance. However, the daily driving schedule of automotive engines is inherently related to unsteady conditions. There are various operating conditions experienced by (diesel) engines that can be classified as transient. Besides the variation of the engine operating point, in terms of engine speed and torque, also the warm up phase can be considered as a transient condition. Chapter 2 has to do with this thermal transient condition; more precisely the main issue is the performance of a Selective Catalytic Reduction (SCR) system during cold start and warm up phases of the engine. The proposal of the underlying work is to investigate and identify optimal exhaust line heating strategies, to provide a fast activation of the catalytic reactions on SCR. Chapters 3 and 4 focus the attention on the dynamic behavior of the engine, when considering typical driving conditions. The common approach to dynamic optimization involves the solution of a single optimal-control problem. However, this approach requires the availability of models that are valid throughout the whole engine operating range and actuator ranges. In addition, the result of the optimization is meaningful only if the model is very accurate. Chapter 3 proposes a methodology to circumvent those demanding requirements: an iteration between transient measurements to refine a purpose-built model and a dynamic optimization which is constrained to the model validity region. Moreover all numerical methods required to implement this procedure are presented. Chapter 4 proposes an approach to derive a transient feedforward control system in an automated way. It relies on optimal control theory to solve a dynamic optimization problem for fast transients. From the optimal solutions, the relevant information is extracted and stored in maps spanned by the engine speed and the torque gradient.

There is no abstract available for this thesis.

Hybrid vehicles (HV), comprising a conventional ICE-based powertrain and a secondary energy source, to be converted into mechanical power as well, represent a well-established alternative to substantially reduce both fuel consumption and tailpipe emissions of passenger cars. Several HV architectures are either being studied or already available on market, e.g. Mechanical, Electric, Hydraulic and Pneumatic Hybrid Vehicles. Among the others, Electric (HEV) and Mechanical (HSF-HV) parallel Hybrid configurations are examined throughout this Thesis. To fully exploit the HVs potential, an optimal choice of the hybrid components to be installed must be properly designed, while an effective Supervisory Control must be adopted to coordinate the way the different power sources are managed and how they interact. Real-time controllers can be derived starting from the obtained optimal benchmark results. However, the application of these powerful instruments require a simplified and yet reliable and accurate model of the hybrid vehicle system. This can be a complex task, especially when the complexity of the system grows, i.e. a HSF-HV system assessed in this Thesis. The first task of the following dissertation is to establish the optimal modeling approach for an innovative and promising mechanical hybrid vehicle architecture. It will be shown how the chosen modeling paradigm can affect the goodness and the amount of computational effort of the solution, using an optimization technique based on Dynamic Programming. The second goal concerns the control of pollutant emissions in a parallel Diesel-HEV. The emissions level obtained under real world driving conditions is substantially higher than the usual result obtained in a homologation cycle. For this reason, an on-line control strategy capable of guaranteeing the respect of the desired emissions level, while minimizing fuel consumption and avoiding excessive battery depletion is the target of the corresponding section of the Thesis.