Thesis (M.S. - Soil, Water and Environmental Science)--University of Arizona, 1997. / Includes bibliographical references (leaves 43-48).

Sappi's Ngodwana integrated Kraft pulp and paper mill was used as case study for the application and evaluation of the water pinch technique. The technique of water pinch originates from energy pinch, but uses mass flow and contaminant concentration to identify water and effluent reduction opportunities. The classical meaning of pinch, as defmed by energy pinch has however been changed to a more modem meaning. Historically the terms water or energy pinch was used to refer to the points where two composite curves touched on energy or water graphs. This graphical meaning of pinch is gradually being replaced to refer to the optimal po int proposed by a numerical solver beyond which improvement of the water network is no longer possible for the given inputs. The water pinch technique was applied by means of a numerical solver that used mixed integer non-linear programming to optimise to the minimum cost for running the water network under investigation. The problem defmition was defined in terms of costs associated with the use of utilities, raw material, treatment facilities and process units. It was also possible to define factors such as environmental impact, corrosion, fouling, scaling, cooling tower treatment cost, legal risk etc in terms of a penalty cost. The water pinch technique has been refined in software packages that are user friendly, ca~ble of handling multi-contaminants and suitable for varying flows. The software package WaterPinch by Linnhoff March was used. The case study was applied on Ngodwana mill that has an already highly closed water system with effluent generation rates as low 20 kL per ton of pulp and paper. The pinch study included sodium, chloride, calcium, suspended solids and COD as contaminants. The study investigated different applications of the pinch technique. The following was concluded: • The mill's understanding of its current restrictions, ()l pinch points, of its water network was confirmed. No new pinch points have been identified of which the mill was not aware. This indicates that the mill was already highly knowledgeable about its water system. This was expected of a mill that has a very low specific-effluent-generation rate. Water pinch was unable to significantly improve on the effluent generation rate of the mill. • The pinch analysis has identified opportunities of mixing small quantities of waste streams into process water streams to replace fresh water. These changes can introduce minor water savings and new risks to the process that have to be understood better before implementation. • The mill has progressed far with the design and costing of a proposed effluent treatment plant (ERPl). The integration of this treatment plant into the water network was investigated using the pinch technique. The pinch solver suggested a totally different approach to the integration of the ERPI plant compared to design of the mill. The mill's design revolves around the treatment of low chloride streams in the ERPl plant and using of the treated water as make-up to the cooling towers. Sodium was recovered as raw material from the cooling towers' blow-down. Pinch proposed treatment of the high cWoride containing streams and returning the streams to users suitable of using high chloride water. The network proposed by mill's design generates 8.2 MLlday effluent less than the pinch proposal, and recovers sodium as raw material. The proposal presented by pinch is not recommended and points to the difficulty in simulating factors, such as raw material recovery, in a pinch analysis. • Users for the excess storm water were identified using water pinch and will be suitable for implementation. The mill has mwever decided on alternative sinks for the storm water based on considerations such as process inter-dependency, risks associated with contamination and general management philosophy for the different systems in the mill. These considerations could have been included into the pinch solver, but were not because it was of interest what the second best option would be. • The pinch investigation proved useful to confirm certain understandings of the mill. The investigation confirmed the difficulty of improving the water systems of the mill due to the fact that Ngodwana is already a highly closed and integrated mill. Numerous smaller process changes have been identified by the pinch solver and could be investigated further for smaller process improvements. • It i; recommended that pinch technology be applied again when the mill plans to make major process changes or expansions. It is also recommended to use water pinch on a more frequent basis in smaller sections of the mill or for other evaluations in the mill. As a group Sappi could benefit from the use of water pinch, especially in situations where the water network of the mill is not already water efficient. • The recommendations and conclusions in this report have not been subjected to technical and economical feasibility studies. Extensive further studies must be conducted before implementation of any of the results. Further studies must include impacts from process dynamics, long term effects, impacts from other contaminants that have not been simulated, etc. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, Durban, 2009.

No description available.

Malaysia embarked on a privatization program in 1983. The overall aim was to relieve the financial and administrative burden of the government and to improve the efficiency and productivity of government enterprises. One of the sectors privatized was the water supply in Penang with the major objective of ensuring that the privatized water company, known as Penang Water Supply Corporation (PWSC), provides better quality services to its customers. The PWSC must attempt to satisfy its customers who must perceive that their needs are being met and to capture the voices of the customers in order to provide improved services. / This study assessed the suitability of the SERVQUAL instrument for measuring service quality in Malaysian water supply sector. It attemped to evaluate the quality of services provided by PWSC through the use of the SERVQUAL instrument to measure industrial customers' expectations and perceptions of the quality of service. SERVQUAL measures five service dimensions: tangibles, reliability, responsiveness, assurance and empathy. Expectations, perceptions and service quality scores were assessed and their significance interpreted. The research was conducted via a questionnaire survey. The results indicated that SERVQUAL to be an appropriate instrument to measure water supply service in Malaysia and three factors appear as dimensions of service quality. Analysis of the results revealed that industrial customers rated the service quality provided by PWSC as above average. Higher expectation than perception scores were recorded on all features of service quality indicating that customers expected a better quality of service from PWSC. An Extended Gaps Model of Service Quality was used to identify the factors contributing the service quality shortfalls. Strategies to improve service quality of PWSC were proposed. / Thesis (DBA(DoctorateofBusinessAdministration))--University of South Australia, 2004.

AECI Bioproducts (Bioproducts) is part of an industrial complex located at Umbogintwini, approximately 26 km south of Durban, Kwazulu-Natal. This system was selected for water pinch investigation, as it is one of the major users of freshwater on the complex and hence discharges a related quantity of wastewater, amounting to approximately 400 ML per annum. Bioproducts is a manufacturer of l-lysine, which is an animal feed additive. Water stream flowrate and purity data, as well as operating cost information, were obtained from plant records at AECI Bioproducts. Limiting flowrate and purity conditions for the water-using operations were established from a mass balance over the entire system using the Linnhoff-March software, WaterTracker. Subject to the specified constraints and operating costs, the problem was to determine the design of the water-using subsystem. No treatment plants were included in the study, as none exist at the facility. Three scenarios were investigated, which examined the operating variability of one of the evaporators on the site (the AS evaporator), which produces a condensate source of variable purity. The operating cost target and network design for each scenario was determined using the Linnhoff-March software, WaterPinch. Alterations from current operating practice were identified and associated savings (water-using network operating cost and freshwater flowrate) were highlighted. A robust optimal design was identified, with a recycle, which was consistent for all scenarios investigated. The degree of reuse of the AS evaporator condensate source was determined to be dependent on the purity of the source. The limiting constraint was identified at the sea pipeline, for suspended solids (SS): a prohibitively low discharge concentration constraint was identified as posing the major obstacle for saving. The potential for saving was investigated by incrementing the SS concentration constraint and subsequently the free and saline ammonia (FSA) constraint and allowing for the broth effluent to be discharged via the sea pipeline (which was previously disallowed by an effluent exemption). Although relatively small savings were identified through process integration (from 0.61% to 1.56% of the water-using network operating cost), the analysis identified a potential saving of over 70% of the water-using network operating cost, with relaxation of the sea pipeline SS and FSA constraint. / Theses (M.Sc.)-University of Natal, Durban, 2002.

This paper presents the results of the spike tests performed in the alternative water supply pilot testing program for the City of Pembroke Pines. It establishes the effectiveness of a protocol that can be used to gain further insight on the rejection capacities of RO membranes. An in-depth study of the molecular descriptors affecting rejection by RO membranes is presented and used in the development of a discriminant function analysis. This analysis proved to be an effective way to predict the passage of Emerging Substances of Concern (ESOCs) through RO membrane. Further, a principal component (PC) analysis was performed to determine which factors accounted the largest variation in RO permeability. Additionally, this paper defines the groundwork for a discriminant analysis model that, if further developed, could serve as an important tool to predict the rejection capabilities of RO treatment when handling with ESOCs. / by Fernando J. Pleitez Herrera. / Thesis (M.S.C.S.)--Florida Atlantic University, 2012. / Includes bibliography. / Mode of access: World Wide Web. / System requirements: Adobe Reader.

Pinch Analysis, in the broadest sense, is concerned with the optimal use of resources (material or energy) in a multi-process system. Pinch Analysis based techniques have emerged for water systems over the past decade. A major assumption that has been made in applying these techniques is that a process system can be segregated into a set of process streams and a set of water streams. With this distinction in place, only the water streams are considered in the Pinch Analysis with the process streams represented implicitly. This approach has obvious limitations in situations where a clear distinction between process streams and water streams cannot be made. The chlor-alkali process is an example of a system in which the clear distinction between process streams and water streams cannot be made. Water is intrinsically involved in the process, serving as a carrier medium for raw materials and eventually becoming part of the products produced by the complex. Hydrochloric acid and caustic soda are reagents which are both used within and produced by the complex. These reagents are required by the process at a range of concentrations and the concentrated reagent is diluted to the required concentrations using demineralised water. Within the chlor-alkali complex, a number of effluents containing the reagent species are available and are typically sent to drain. It is conceivable that these effluents might be recovered and used for dilution purposes instead of demineralised water. This would bring about a reduction in the amount of water and concentrated reagent used and the amount of effluent produced by the complex. Given the economic value of these reagents relative to water, their recovery, if feasible, is likely to dominate the optimal water-use and effluent generation strategy. Current Water Pinch Analysis theory relies on the distinction being made between process streams and water streams and does not consider the recovery of reagents or the presence of desirable species within the system. In addition, the assumption is made that species are non-reactive; reactive species such as hydrogen chloride and sodium hydroxide, fall outside the scope of the current theory. The objectives of this study have included the development of an approach which is able to address these limitations of the existing theory. This approach, termed Combined Water and Materials Pinch Analysis seeks to identify optimal use strategies for raw materials and reagents, in addition to water-use and effluent generation. The approach combines mathematical programming with conceptual insights from Water Pinch Analysis. The approach is based on the optimisation of a superstructure which represents the set of all possible flow configurations for water, reagents and raw materials between the various operations within the process system; this problem is solved as a nonlinear programming (NLP) problem using standard optimisation tools. The application of the developed approach to the Sasol Polymers chlor-alkali complex at Umbogintwini, south of Durban, has been a further objective of this study. Given the variety of process operations present within the complex, which differ both in terms of their physical structure and function, individual process models for these operations were required. These models were described in terms of four basic functional elements, namely, mixing, flow separation, component separation and reaction, and incorporated into the superstructure. Given the complexity of the problem, the process system was divided into three subsystems which were optimised in isolation from each other. These results were subsequently integrated to reflect the performance of the subsystems in combination with each other. The results showed a potential reduction of 14% in water-use and 42% in effluent production by the complex, relative to the existing operating configuration. Amongst other savings in material use, the results indicated a 0.2% reduction in the use of salt, a 1.6% reduction caustic soda use and an 8.3% reduction in the use of hydrochloric acid. Economically, the potential saving identified was R 945 727 per annum, based on operating costs in the year 2000. The final objective of this study was the interpretation of the pinch as it relates to the Combined Water and Materials Pinch Analysis problem. A general definition of the pinch was proposed; according to this definition, the pinch corresponds to that constraint or set of constraints which limits the performance of the system, that is, prevents it from further improvement. For the Combined Water and Materials Pinch Analysis problem, this performance is measured in terms of the operating cost. This definition is thus a departure from its usual thermodynamic interpretation of the pinch; in addition, the pinch is defined in terms of a constraint or a set of constraints instead of a point. These constraints are identified by an analysis of the marginal values provided by the optimisation algorithm. Marginal values are also used as a means of identifying process interventions which may be effected such that the performance of the system may be improved further. / Thesis (M.Sc.Eng.)-University of Natal, 1989.

The objective of this investigation was to utilise water pinch analysis as a tool for the optimisation of fresh water use in an integrated pulp and paper mill. The investigation was carried out at Mondi Paper in Merebank, south of Durban. The pulp and paper manufacturing process is a large consumer of fresh water and minimising the amount of fresh water used in the processes is beneficial from both a cost and environmental point of view. There are examples of mills which have "closed" their water systems to the extent that fresh water make up is minimal and most of the water is recycled and reused in a closed loop. These examples provide guidance on the basis of proven methods for reducing water consumption in the pulp and paper industry and can be used as a reference for mills wishing to reduce water consumption by making use of tried and tested methods. This investigation sought to provide an alternative method to identifying potential savings in fresh water consumption by making use of water pinch analysis. This was done at Mondi Paper by analysing individual parts of the mill and then a larger section of the mill which included both pulp and paper production. Flow rates of water streams and fibre content in those streams were obtained from plant data, where available, and this data was used to produce.a mass balance using the Linnhoff-March software, Water Tracker. The balance produced using Water Tracker provided the missing flow and fibre content data and this data was used as the input for the Linnhoff-March software, Water Pinch , to perform the water pinch analysis. The results achieved when analysing the individual parts of the mill did not demonstrate potential for significant savings in fresh water consumption, however the analysis of the integrated section of the mill identified a potential reduction in fresh water. It was found that the application of a single contaminant analysis to the larger section of the mill identified a possible reduction in the freshwater requirement of 8.1% and a reduction in effluent generated of 5.4%. This is a savings of R1 548 593 per annum based on 2003 costs of fresh water and effluent disposal. This analysis was conducted using the most simplified representation possible to produce meaningful results in order to evaluate the effectiveness of water pinch analysis in optimising the fresh water consumption in an integrated pulp and paper mill. It is demonstrated that water pinch analysis is potentially a useful tool in determining the minimum fresh water requirement of a site. / Thesis (M.Sc.Eng.)-University of Natal, Durban, 2003.

Project Completion Report, OWRT Project No. A-043-ARIZ / Agreement No. 14-31-0001-4003 / Project Dates: July 1973 - June 1974 / Acknowledgment: The work upon which this report is based was supported in large part by funds provided by the United States Department of the Interior, Office of Water Research and Technology, as authorized under the Water Resources Research Act of 1964. / A growing demand for energy production in Arizona has increased the need for assembling and analyzing water resource information relative to energy production, especially electrical power generation. Unit water requirements for cooling of electrical plants, combined with projections of future electrical power demands in Arizona, provide a perspective on future quantities of water needed for cooling. Probabilistic estimates of storage reserves in Arizona groundwater basins indicate that some prospective plant sites can be supplied from groundwater for the 30 -year life of the plant, while others cannot. An estimate of comparative cost for supplying groundwater versus municipal wastewater for cooling electrical plants at selected sites in Arizona showed that use of wastewater would result in considerable savings over use of groundwater, at all sites considered.

A study in economic geography, this thesis attempts to determine the importance of water for process supply and effluent disposal in industrial location decisions. It is postulated that industry faces physical, institutional, and technologic-economic constraints when evaluating the water component in location problems. Each of these three constraints is analyzed and evaluated for British Columbia's pulp and paper industry, with a view to discovering its effect on the range of spatial choice enjoyed by firms. A number of general conclusions emerge from the investigation. Although a theoretic location proof is not offered, the study raises a number of arguments which indicate water has been over-emphasized in industrial location decisions, and that industry exhibits greater spatial mobility regarding water requirements than is contended in the geographical and technical literature. Of the three constraints, it appears that those of a technologic-economic nature impose the severest limitations on spatial choice; physical, the least. Institutional regulations are found to provide industry with incorrect signals for decision making — the suggestion is offered that effluent control programs based upon economic rather than biological criteria would remove this problem. The implications of the above conclusions for future geographic inquiry regarding water management and development is considered in the concluding section of the study. / Arts, Faculty of / Geography, Department of / Graduate