Spelling suggestions: "subject:"entegrated circuits -- matematerials"" "subject:"entegrated circuits -- datenmaterials""
1 |
Electromigration critical length effect and early failures in Cu/oxide and Cu/low k interconnectsLee, Ki-don 28 August 2008 (has links)
Not available / text
|
2 |
Applied mechanical tensile strain effects on silicon bipolar and silicon-germanium heterojunction bipolar devicesNayeem, Mustayeen B. January 2005 (has links)
Thesis (M. S.)--Electrical and Computer Engineering, Georgia Institute of Technology, 2006. / Dr. John D. Cressler, Committee Chair ; John Papapolymerou, Committee Member ; Joy Laskar, Committee Member.
|
3 |
Materials research on metallized aluminum-nitride for microelectronic packagingNewberg, Carl Edward, 1962- January 1988 (has links)
The use of aluminum nitride as a substrate material for microelectronics is examined. A brief look at thermal, mechanical, and electrical properties of aluminum nitride show that it is a viable alternative material for this use. A study of the interfaces between aluminum nitride and several thick film pastes (palladium silver conductor, ruthenium oxide resistor, and gold conductor) was performed with optical microscopy, scanning electron microscopy, and energy dispersive spectroscopy. Results of this investigation showed that the contaminants in the substrate material that affect thermal conductivity do not affect the adhesion of the thick film pastes. However, it was found that the lack of certain elements in the binder of the thick film paste could lead to weaker adhesion, and severe degradation of the thick film's adhesion during thermal cycling.
|
4 |
Patterning of Nanostructures by Block Copolymer Self-AssemblyZhang, Xiaojiang Unknown Date
No description available.
|
5 |
HIGH FREQUENCY DIELECTRIC PROPERTIES OF POLYIMIDES FOR MULTILAYER INTERCONNECT STRUCTURESHinedi, Mohamad Fahd, 1964- January 1987 (has links)
One of the most important electrical requirements in high performance electronic systems or high speed integrated circuits, is to process larger numbers of electrical signals at much higher speeds. Signal propagation delay must be minimized in order to maximize signal velocities. Therefore, material with low dielectric constant and low dissipation factor is being sought. In this thesis research measurements of dielectric constant and dissipation factor were performed on commercially available polyimides that are used in multilayer interconnect structures. Capacitor structures with a polyimide dielectric were measured up to a 1GHz frequency and 220°C temperature. Polyimides were concluded to be compatible for use in high performance systems such as multilayer interconnect structures.
|
6 |
Metallization and Modification of Low-k Dielectric MaterialsMartini, David M. 12 1900 (has links)
Aluminum was deposited onto both Teflon AF and Parylene AF surfaces by chemical vapor deposition of trimethylaluminum. This work shows that similar thin film (100 Angstroms) aluminum oxide adlayers form on both polymers at the low temperature dosing conditions used in the studies. Upon anneal to room temperature and above, defluorination of the polymer surfaces increased and resulted in fluorinated aluminum oxide adlayers; the adlayers were thermally stable to the highest temperatures tested (600 K). Angle-resolved spectra showed higher levels of fluorination toward the polymer/adlayer interface region. Copper films were also deposited at low temperature onto Teflon AF using a copper hexafluoroacetylacetonate-cyclooctadiene precursor. Annealing up to 600 K resulted in the loss of precursor ligands and a shift to metallic copper. As with aluminum adlayers, some polymer defluorination and resulting metal (copper) fluoride was detected. Parylene AF and polystyrene films surfaces were modified by directly dosing with water vapor passed across a hot tungsten filament. Oxygen incorporation into polystyrene occurred exclusively at aromatic carbon sites, whereas oxygen incorporation into parylene occurred in both aromatic and aliphatic sites. Oxygen x-ray photoelectron spectra of the modified polymers were comparable, indicating that similar reactions occurred. The surface oxygenation of parylene allowed enhanced reactivity toward aluminum chemical vapor deposition. Silicon-carbon (Si-Cx) films were formed by electron beam bombardment of trimethylvinylsilane films which were adsorbed onto metal substrates at low temperatures in ultra-high vacuum. Oxygen was also added to the films by coadsorbing water before electron beam bombardment; the films were stable to more than 700 K, with increasing silicon-oxygen bond formation at elevated temperatures. Copper metal was sputter deposited in small increments onto non-oxygenated films. X-ray photoelectric spectra show three-dimensional copper growth (rather than layer-by-layer growth), indicating only weak interaction between the copper and underlying films. Annealing at elevated temperatures caused coalescence or growth of the copper islands, with spectra indicating metallic copper rather than copper oxide.
|
Page generated in 0.1173 seconds