This thesis focuses on utilizing the persistent voltage vector injections by finite control set model predictive control (FCSMPC) to enable simultaneous estimations of both position and parameters in order to realize robust sensorless interior permanent magnet synchronous machine (IPMSM) drives valid at the entire operating region including no-load standstill without any additional signal injection and switchover. The system (here, IPMSM) needs to meet certain observability conditions to identify the parameters and position. Moreover, each combination of the parameters and/or position involves different observability requirements which cannot be accomplished at every operating point. In particular, meeting the observability for parameters and position at no-load standstill is more challenging. This is overcome by generating persistent excitation in the system with high-frequency signal injection. The FCSMPC scheme inherently features the persistent excitation with voltage vector injection and hence no additional signal injection is required. Moreover, the persistent excitation always exists for FCSMPC except at the standstill where the control applies the null vectors when the reference currents are zero. However, introducing a small negative d axis current at the standstill would be sufficient to overcome this situation.The parameter estimations are investigated at first in this thesis. The observability is analyzed for the combinations of two, three and four parameters and experimentally validated by online identification based on recursive least square (RLS) based adaptive observer. The worst case operating points concerning observability are identified and experimentally proved that the online identification of all the parameter combinations could be accomplished with persistent excitation by FCMPC. Moreover, the effect of estimation error in one parameter on the other known as parameter coupling is reduced with the proposed decoupling technique. The persistent voltage vector injections by FCSMPC help to meet the observability conditions for estimating the position, especially at low speeds. However, the arbitrary nature of the switching ripples and absence of PWM modulator void the possibility of applying the standard demodulation based techniques for FCSMPC. Consequently, a nonlinear optimization based observer is proposed to estimate both the position and speed, and experimentally validated from standstill to maximum speed. Furthermore, a compensator is also proposed that prevents converging to saddle and symmetrical ( ambiguity) solutions. The robustness analysis of the proposed nonlinear optimization based observer shows that estimating the position without co-estimating the speed is more robust and the main influencing parameters on the accuracy of the position estimation are d and q inductances. Subsequently, the proposed nonlinear optimization based observer is extended to simultaneously estimate the position, d and q inductances. The experimental results show the substantial improvements in response time, and reduction in both steady and transient state position errors. In summary, this thesis presents the significance of persistent voltage vector injections in estimating both parameter and position, and also shows that nonlinear optimization based technique is an ideal candidate for robust sensorless FCSMPC. / Thesis / Doctor of Philosophy (PhD)

This thesis studies the brushless permanent magnet synchronous (BLPM) machine design for electric vehicle (EV) and hybrid electric vehicle (HEV) application. Different rotor topologies design, winding design, and multiphase designs are investigated and discussed. The Nissan Leaf interior permanent magnet (IPM) traction machine has been widely analyzed and there is much public domain data available for the machine. Hence, this machine is chosen as a representative benchmark design. First, the Nissan Leaf machine is analyzed via finite element analysis (FEA) and the results confirmed via published experimental test data. The procedure is then applied to all the following machine designs and results compared. Then the Nissan Leaf machine rotor is redesigned to satisfy the performance specification with sinusoidal phase current in the full range for the same performance specification and permanent magnet material. Afterword, a comparative study assessing the design and performance attributes of the Nissan Leaf IPM machine, when compared to a surface permanent magnet (SPM) machine designed within the main Nissan Leaf machine dimensional constraints. The study illustrates and concludes that both the IPM and SPM topologies have very similar capabilities with only subtle differences between the design options. The results highlight interesting manufacturing options and materials usage. The grain boundary diffusion processed (GBDP) magnets are proposed to reduce the rare earth material content in the permanent magnet machines, especially subject to high load and high temperature operating scenarios by preventing or reducing the onset of demagnetization. The design and analysis procedure of BLPM machine with GBDP magnets are put forward. In the end, the Nissan Leaf IPM machine is taken as an example to verify the analysis procedure. and the results illustrates that IPM machines with GBDP magnets can realize torque and maintain efficiency at high loads while being less prone to demagnetization. A new multi-phase synchronous reluctance machine (SRM) with good torque performance and conventional voltage source inverter is introduced for traction machine applications. Although the torque density is low compared with BLPM machine, the SRM machine gets rid of permanent magnets and achieve low torque ripple compared with switched reluctance machine when the asymmetric inverter is replaced with conventional voltage source inverter. The concentrated windings are designed and studied with both IPM and SPM rotor according to the Nissan Leaf machine requirements of performance and dimension to investigate how the concentrated windings affect the machine performance and manufacturability and cost. 9-, 12-, 15- slot concentrated windings’ stator share the same slot area with the Nissan Leaf machine distributed winding and the performance are evaluated and compared. Multi-phase concentrated windings machines with IPM and SPM rotor are designed and analyzed based on the Nissan Leaf machine specification and dimension constraints. The performance of 23-phase, 5-phase, 9-phase machine at low speed and top speed are studied and the advantages and disadvantages are compared in terms of torque quality, efficiency, and power electronic requirements. / Thesis / Doctor of Philosophy (PhD)

QC 20111214