No description available.

Conductive thin films of poly(3,4-ethylenedioxythiophene)-polystyrenesulfonate (PEDOT-PSS) were created via layer-by-layer assembly. The PEDOT-PSS was used in an aqueous solution as an anionic polyelectrolyte, with both linear and branched polyethylenimine (PEI) and poly(allylamine hydrochloride) (PAH) in the positive aqueous solution. The electrical conductivity was varied by altering pH, concentration, polyelectrolyte, and doping the PEDOT with dimethylsulfoxide (DMSO). The most conductive 12BL samples were doped with 1wt% DMSO and have a sheet resistance of approximately 8kΩ/□. Despite exhibiting good initial conductivity, these PEDOT based thin films degrade under ultraviolet (UV) exposure. UV absorbing nanoparticles were added into the cationic solution in an effort to reduce UV sensitivity. The final bilayers of the films contained either colloidal titanium dioxide (TiO2) or carbon black (CB) and the films were exposed to a 365nm UV-light with an intensity of 2.16mW/cm2 for 9 days. The UV light at this intensity correlates to approximately four years of sunlight. The initial sheet resistances for all samples were similar, but the UV-degradation was reduced by a factor of 5 by utilizing TiO2 and CB in the final bilayers. In addition to being the most conductive after UV exposure, the TiO2 containing film was also 27% more optically transparent than the pure PEDOT films. These additional UV-absorbing nanoparticles extend the operational life of the PEDOT films and, in the case of TiO2, do so without any reduced transparency.

Layer-by-layer (LbL) assembly based on ionic interactions has proven to be a versatile route for surface modification and construction of ultrathin nanocomposites. Covalent LbL assembly based on facile ‘click’ covalent bond formation is an effective alternative, especially for the applications where a more robust ultrathin films or nanocomposites is desired. The subject of this dissertation focuses on the design of three different covalent LbL assemblies and their applications on conductive thin films, superhydrophobic surfaces, and solute responsive surfaces, respectively. Surface modification of PE substrates using covalent LbL assembly with PEI and Gantrez is a successful route to prepare a surface graft. The procedure is relative easy, fast and reproducible. Grafting multiple layers of PEI/Gantrez to the PE powder surface provided excellent coverage and promoted stable LbL film growth and excellent adhesion. This carbon black (CB) coated powder was compression molded into films, and their conductivity was measured, which revealed a percolation threshold below 0.01 wt % CB for the PEI-grafted system. Electrical conductivity of 0.2 S/cm was achieved with only 6 wt % CB, which is exceptional for a CB-filled PE film. Direct amination of MWNTs with PEI is a convenient and simple method leading to highly functionalized product that contains 6-8 % by weight PEI. Superhydrophobic PE films can be formed either from ionic LbL self-assembly of MWNT-NH-PEIs and poly(acrylic acid) or from covalent LbL self-assembly of MWNTNH- PEIs and Gantrez when the final graft is acrylated with octadecanoic acid. While the ionically assembled nanocomposite graft is labile under acid, the covalently assembled graft is more chemically robust. Responsive surfaces with significant, reversible, reproducible wettability changes can be prepared by covalent LbL grafting using PNIPAM-c-PNASI and aminated silica nanoparticles. A 65º ΔΘ value was observed with water vs. 1.4 M Na2SO4. The prepared film shows a high surface roughness of ~300 nm, which contributes to the large solute responsive ΔΘ values. The surfaces are reconfigurable in different solute conditions and that the changes in water contact angle are likely due to combination of change in surface roughness along with swell and intercalation of the solute ions into the PNIPAM surface.

Layer-by-layer (LbL) assembly has proven to be a powerful technique for assembling thin films with a variety of properties including electrochromic, molecular sensing, oxygen barrier, and antimicrobial. LbL involves the deposition of alternating cationic and anionic ingredients from solution, utilizing the electrostatic charges to develop multilayer films. The present work incorporates cationic antimicrobial agents into the positively-charged layers of LbL assemblies. When these thin films are exposed to a humid environment, the antimicrobial molecules readily diffuse out and prevent bacterial growth. The influence of exposure time, testing temperature, secondary ingredients and number of bilayers on antimicrobial efficacy is evaluated here. Additionally, film growth and microstructure are analyzed to better understand the behavior of these films. The antimicrobial used here is a positively-charged quaternary ammonium molecule (e.g. cetyltrimethylammonium bromide [CTAB]) that allow assemblies to be made with or without an additional polycation like polydiallyldimethylamine. While films without this additional polymer are effective, they do not have the longevity or uniformity of films prepared with its addition. All of the recipes studied show linear growth as a function of the number of bilayers deposited and this growth is relatively thick (i.e. > 100 nm per bilayer). In general, 10-bilayer films prepared with CTAB and poly(acrylic acid) are able to achieve a 2.3 mm zone of inhibition against S. aureus bacteria and 1.3 mm against E. coli when test are conducted at body temperature (i.e. 37oC). Fewer bilayers reduces efficacy, but lower test temperatures improve zones of inhibition. As long as they are stored in a dry atmosphere, antimicrobial efficacy was found to persist even when films were used four weeks after being prepared. The best films remain effective (i.e. antimicrobially active) for 4-6 days of constant exposure to bacteria-swabbed plates. This technology holds promise for use in transparent wound bandages and temporary surface sterilization.

An amperometric glucose biosensor was fabricated using electospun polyaniline fibers. Polyaniline was reacted with camphorsulfonic acid to produce a salt, which was then dissolved in chloroform containing polystyrene. Using this solution, fibers were formed and collected by electrospinning. Glucose oxidase was immobilized onto these fibers using an electrostatic layer-by-layer adsorption technique. In this method, poly(diallyldimethylammonium chloride) was used as the counter ion source. The level of adsorption was examined and evidence of layer-by-layer adsorption was obtained using a quartz crystal microbalance technique. A biosensor was fabricated from these fibers as a working electrode, and used to measure the glucose concentration accurately.

No description available.

Microgels are solvent swollen, cross-linked polymer macromolecules of micro or nanoscale dimensions. In this work, microgels are used as versatile building blocks in layer-by-layer assemblies to form thin coatings. While conceptually simple materials, these microgel-based films actually possess extremely complex behavior as evidenced by two particular areas. First, microgel films have self-healing properties, allowing them to rapidly recover from damage in the presence of solvent. The healing step requires rearrangement of film components, demonstrating the dynamic and mobile nature of the films. Second, fibroblasts display complex behavior on microgel films arising from the properties of the coating. A chemical crosslinking treatment of the film affects the film network structure in a concentration-dependent manner. These network changes result in altered mechanical properties that are the primary controlling factor in determining cell behavior at the interface. These data suggest that fibroblasts are not solely controlled by the film elasticity, but rather by the viscoelasticity, and there is a viscoelastic range that results in maximal cell spreading.

No description available.

The problems and high medical costs associated with chronic wounds necessitate an economical bioactive wound dressing. A new strategy was investigated to inhibit MMP-9 proteases and to release epidermal growth factor (EGF) to enhance healing. Doxycycline (DOX) and EGF were encapsulated on polyacrylic acid modified polyurethane film (PAA-PU) using Layer-by-Layer (LbL) assembly. The number of bilayers tuned the concentration of DOX and EGF released over time with over 94% bioactivity of EGF retained over 4 days. A simple wound model in which MMP-9 proteases were added to cell culture containing fibroblast cells demonstrated that DOX inhibited the proteases providing a protective environment for the released EGF to stimulate cell migration and proliferation at a faster healing rate. In the presence of DOX, only small amounts of the highly bioactive EGF are sufficient to close the wound. Results show that this is new and promising bioactive dressing for effective wound management.

The problems and high medical costs associated with chronic wounds necessitate an economical bioactive wound dressing. A new strategy was investigated to inhibit MMP-9 proteases and to release epidermal growth factor (EGF) to enhance healing. Doxycycline (DOX) and EGF were encapsulated on polyacrylic acid modified polyurethane film (PAA-PU) using Layer-by-Layer (LbL) assembly. The number of bilayers tuned the concentration of DOX and EGF released over time with over 94% bioactivity of EGF retained over 4 days. A simple wound model in which MMP-9 proteases were added to cell culture containing fibroblast cells demonstrated that DOX inhibited the proteases providing a protective environment for the released EGF to stimulate cell migration and proliferation at a faster healing rate. In the presence of DOX, only small amounts of the highly bioactive EGF are sufficient to close the wound. Results show that this is new and promising bioactive dressing for effective wound management.