<p> Lifted non-premixed turbulent jet flames in the Transverse Instability Combustor (TIC) have been analyzed using qualitative and quantitative methods. Lifted flames in the TIC have been observed to stabilize about zero to five injector exit diameters downstream of the dump plane into the chamber and exhibit pulsating, unsteady burning. Anchored flames immediately begin reacting in the injector recess and burn evenly in a uniform jet from the injector exit through the entire optically accessible region. Statistically significant, repeatable behavior lifted flames are observed. It is shown that the occurrence of lifted flames is most likely for an injector configuration with close wall-spacing, second greatest for a configuration with close middle-element spacing, and lowest for a configuration with even element-spacing. For all configurations, of those elements that have been observed to lift, the center element is most likely to lift while the second element from the wall was likely. Flames at the wall elements were never observed to lift. Evidence is shown to support that close injector element spacing and stronger transverse pressure waves aid lateral heat transfer which supports flame stability in the lifted position. It is hypothesized that the stability of lifted flames is influenced by neighboring ignition sources, often a neighboring anchored flame. It is also shown that instances of lifted flames increase with the root-mean-squared magnitude of pressure fluctuation about its mean (P’ RMS) up to a threshold, after which flames stabilize in the anchored recess position.</p> <p>Dynamic mode decomposition (DMD) and proper orthogonal decomposition (POD) analyses of CH* chemiluminescence data is performed. It is found that lateral ignition of the most upstream portion of lifted flames is dominated by the 1W mode. Furthermore, it is shown that low-frequency high energy modes with spatial layers resemble intensity-pulses, possibly attributable to ignition. These modes are trademarks of CH* chemiluminescent intensity data of lifted flames. It was also shown that the residence time in the chamber may be closely associated with those low-frequency modes around 200 Hz. DMD and POD were repeated for a downstream region on the center element, as well as a near-wall element, highlighting differences between the lifted flame dynamics in all three regions. </p> <p>It is shown that lifted flames are best characterized by their burning behavior and in rare cases may stabilize in the recess, while still being “lifted”. Furthermore, it is shown that flame position differentiation can extend into an initial period of highly stable combustor operation. Dynamic mode decomposition is explored as potential method to understand physical building blocks of proper orthogonal spatial layers. Non-visual indicators of lifted flames within the high-frequency (HF) pressure signal are sought to seek a method that allows for observation of lifted flames in optically inaccessible combustors, such as those in industry. Some attributes of power-spectral diagrams and cross-correlations of pressure signals are provided as potential indicators. </p>

This thesis is concerned with investigations on two related issues of turbulent jet diffusion flame, namely (a) stabilization at liftoff and (b) autoignition in a turbulent jet diffusion flame. The approach of Conditional Moment Closure (CMC) has been taken. Fully elliptic first order CMC equations are solved with detailed chemistry to simulate lifted H2/N2 flame in vitiated coflow. The same approach is further used to simulate transient autoignition process in inhomogeneous mixing layers. In Chapter 1, difficulties involved in numerical simulation of turbulent combustion problems are explained. Different numerical tools used to simulate turbulent combustion are briefly discussed. Previous experimental, theoretical and numerical studies of lifted jet diffusion flames and autoignition are reviewed. Various research issues related to objectives of the thesis are discussed. In Chapter 2, the first order CMC transport equations for the reacting flows are presented. Various closure models that are required for solving the governing equations are given. Calculation of mean reaction rate term for detailed chemistry is given with special focus on the reaction rates for pressure dependent reactions. In Chapter 3, starting with the laminar flow code, further extension is carried to include kε turbulence model and PDF model. The code is validated at each stage of inclusion of different model. In this chapter, the code is first validated for the test problem of constant density, 2D, axisymmetric turbulent jet. Further, validation of PDF model is carried out by simulating the problem of nonreacting jet of cold air issuing into a vitiated coflow. The results are compared with the published data from experiments as well as numerical simulations. It is shown that the results compare well with the data. In Chapter 4, numerical results of lifted jet diffusion flame are presented. Detailed chemistry is modelled using Mueller mechanism for H2/O2 system with 9 species and 21 reversible reactions. Simulations are carried out for different jet velocities and coflow stream temperatures. The predicted liftoff generally agrees with experimental data, as well as joint PDF results. Profiles of mean scalar fluxes in the mixture fraction space, for different coflow temperatures reveal that (1) Inside the flamezone, the chemical term balances the molecular diffusion term, and hence the structure is of a diffusion flamelet for both cases. (2) In the preflame zone, the structure depends on the coflow temperature: for low coflow temperatures, the chemical term being small, the advective term balances the axial diffusion term. However, for the high coflow temperature case, the chemical term is large and balances the advective term, the axial diffusion term being small. It is concluded that, liftoff is controlled (a) by turbulent premixed flame propagation for low cofflow temperature while (b) by autoignition for high coflow temperature. In Chapter 5, the numerical results of autoignition in inhomogeneous mixing layer are presented. The configuration consists of a fuel jet issued into hot air for which transient simulations are performed. It is found that the constants assumed in various modelling terms can severely influence the results, particularly the flame temperature. Hence, modifications to these constants are suggested to obtain improved predictions. Preliminary work is carried out to predict autoignition lengths (which may be defined by Tign × Ujet incase of jet- and coflowvelocities being equal) by varying the coflow temperature. The autoignition lengths show a reasonable agreement with the experimental data and LES results. In Chapter 6, main conclusions of this thesis are summarized. Possible future studies on this problem are suggested.

This thesis describes the application of the first-order Conditional Moment Closure (CMC) to the autoignition of high-pressure fuel jets, and to piloted and lifted turbulent jet flames using classical and advanced CMC submodels. A Doubly-Conditional Moment Closure (DCMC) formulation is further proposed. In the first study, CMC is applied to investigate the impact of C₂H₆, H₂ and N₂ additives on the autoignition of high-pressure CH₄ jets injected into lower pressure heated air. A wide range of pre-combustion air temperatures is considered and detailed chemical kinetics are employed. It is demonstrated that the addition of C₂H₆ and H₂ does not change the main CH₄ oxidisation pathways. The decomposition of these additives provides additional ignition-promoting radicals, and therefore leads to shorter ignition delays. N₂ additives do not alter the CH₄ oxidisation pathways, however, they reduce the amount of CH₄ available for reaction, causing delayed ignition. It is further shown that ignition always occurs in lean mixtures and at low scalar dissipation rates. The second study is concerned with the modelling of a piloted CH₄/air turbulent jet flame. A detailed assessment of several Probability Density Function (PDF), Conditional Scalar Dissipation Rate (CSDR) and Conditional Velocity (CV) submodels is first performed. The results of two β-PDF-based implementations are then presented. The two realisations differ by the modelling of the CSDR. Homogeneous (inconsistent) and inhomogeneous (consistent) closures are considered. It is shown that the levels of all reactive scalars, including minor intermediates and radicals, are better predicted when the effects of inhomogeneity are included in the modelling of the CSDR. The two following studies are focused on the consistent modelling of a lifted H₂/N₂ turbulent jet flame issuing into a vitiated coflow. Two approaches are followed to model the PDF. In the first, a presumed β-distribution is assumed, whereas in the second, the Presumed Mapping Function (PMF) approach is employed. Fully consistent CV and CSDR closures based on the β-PDF and the PMF-PDF are employed. The homogeneous versions of the CSDR closures are also considered in order to assess the effect of the spurious sources which stem from the inconsistent modelling of mixing. The flame response is analysed over a narrow range of coflow temperatures (Tc). The stabilisation mechanism is determined from the analysis of the transport budgets in mixture fraction and physical spaces, and the history of radical build-up ahead of the stabilisation height. The β-PDF realisations indicate that the flame is stabilised by autoignition irrespective of the value of Tc. On the other hand, the PMF realisations reveal that the stabilisation mechanism is susceptible to Tc. Autoignition remains the controlling stabilisation mechanism for sufficiently high Tc. However, as Tc is decreased, stabilisation is achieved by means of premixed flame propagation. The analysis of the spurious sources reveals that their effect is small but non-negligible, most notably within the flame zone. Further, the assessment of several H₂ oxidation mechanisms show that the flame is very sensitive to chemical kinetics. In the last study, a DCMC method is proposed for the treatment of fluctuations in non-premixed and partially premixed turbulent combustion. The classical CMC theory is extended by introducing a normalised Progress Variable (PV) as a second conditioning variable beside the mixture fraction. The unburnt and burnt states involved in the normalisation of the PV are specified such that they are mixture fraction-dependent. A transport equation for the normalised PV is first obtained. The doubly-conditional species, enthalpy and temperature transport equations are then derived using the decomposition approach and the primary closure hypothesis is applied. Submodels for the doubly-conditioned unclosed terms which arise from the derivation of DCMC are proposed. As a preliminary analysis, the governing equations are simplified for homogeneous turbulence and a parametric assessment is performed by varying the strain rate levels in mixture fraction and PV spaces.

This thesis describes the application of the first-order Conditional Moment Closure (CMC) to the autoignition of high-pressure fuel jets, and to piloted and lifted turbulent jet flames using classical and advanced CMC submodels. A Doubly-Conditional Moment Closure (DCMC) formulation is further proposed. In the first study, CMC is applied to investigate the impact of C₂H₆, H₂ and N₂ additives on the autoignition of high-pressure CH₄ jets injected into lower pressure heated air. A wide range of pre-combustion air temperatures is considered and detailed chemical kinetics are employed. It is demonstrated that the addition of C₂H₆ and H₂ does not change the main CH₄ oxidisation pathways. The decomposition of these additives provides additional ignition-promoting radicals, and therefore leads to shorter ignition delays. N₂ additives do not alter the CH₄ oxidisation pathways, however, they reduce the amount of CH₄ available for reaction, causing delayed ignition. It is further shown that ignition always occurs in lean mixtures and at low scalar dissipation rates. The second study is concerned with the modelling of a piloted CH₄/air turbulent jet flame. A detailed assessment of several Probability Density Function (PDF), Conditional Scalar Dissipation Rate (CSDR) and Conditional Velocity (CV) submodels is first performed. The results of two β-PDF-based implementations are then presented. The two realisations differ by the modelling of the CSDR. Homogeneous (inconsistent) and inhomogeneous (consistent) closures are considered. It is shown that the levels of all reactive scalars, including minor intermediates and radicals, are better predicted when the effects of inhomogeneity are included in the modelling of the CSDR. The two following studies are focused on the consistent modelling of a lifted H₂/N₂ turbulent jet flame issuing into a vitiated coflow. Two approaches are followed to model the PDF. In the first, a presumed β-distribution is assumed, whereas in the second, the Presumed Mapping Function (PMF) approach is employed. Fully consistent CV and CSDR closures based on the β-PDF and the PMF-PDF are employed. The homogeneous versions of the CSDR closures are also considered in order to assess the effect of the spurious sources which stem from the inconsistent modelling of mixing. The flame response is analysed over a narrow range of coflow temperatures (Tc). The stabilisation mechanism is determined from the analysis of the transport budgets in mixture fraction and physical spaces, and the history of radical build-up ahead of the stabilisation height. The β-PDF realisations indicate that the flame is stabilised by autoignition irrespective of the value of Tc. On the other hand, the PMF realisations reveal that the stabilisation mechanism is susceptible to Tc. Autoignition remains the controlling stabilisation mechanism for sufficiently high Tc. However, as Tc is decreased, stabilisation is achieved by means of premixed flame propagation. The analysis of the spurious sources reveals that their effect is small but non-negligible, most notably within the flame zone. Further, the assessment of several H₂ oxidation mechanisms show that the flame is very sensitive to chemical kinetics. In the last study, a DCMC method is proposed for the treatment of fluctuations in non-premixed and partially premixed turbulent combustion. The classical CMC theory is extended by introducing a normalised Progress Variable (PV) as a second conditioning variable beside the mixture fraction. The unburnt and burnt states involved in the normalisation of the PV are specified such that they are mixture fraction-dependent. A transport equation for the normalised PV is first obtained. The doubly-conditional species, enthalpy and temperature transport equations are then derived using the decomposition approach and the primary closure hypothesis is applied. Submodels for the doubly-conditioned unclosed terms which arise from the derivation of DCMC are proposed. As a preliminary analysis, the governing equations are simplified for homogeneous turbulence and a parametric assessment is performed by varying the strain rate levels in mixture fraction and PV spaces.