The work contained in this thesis is concerned with the flow behaviour of polymer solutions and melts. It is a theoretical study, though it refers extensively to experimental work by others. Calculations are analytic where possible, though some numerical work is required. The principal source is the theoretical model of linear polymer melts developed by Doi and Edwards. The presentation is as follows: Chapter 1 reviews the experimental properties of polymeric liquids and some of the phenonenological schemes used to describe them. Review material extends into chapter 2 which covers molecular theory, the Doi-Edwards model, and developments in the last few years. Chapter 3 applies the model to the 'spurt effect', a well known unstable flow of linear polymer melts. We show that this may be explained quantitatively by the multivalued constitutive behaviour of the model. Chapter 4 examines the stability of the flow field associated with the spurt effect and shows how certain pulsing periodicities in the flow may be related to the 'normal stress' behaviour of the fluid. Chapter 5 is a case study of a more complex branched polymer: the 'H-polymer'. It is shown that both the linear and non-linear viscoelastic response may be calculated in a straightforward extension of the Doi-Edwards model, comparing favourably with experiments to date.

No description available.

This dissertation presents a numerical study using molecular dynamic simulations that interrogates the polymer structure as it is strained continuously in time and correlates it with the stress developed in it. We investigate the role of external control variables such as temperature, strain-rate, chain length, and density. At temperatures higher than glass transition, stress anisotropy is reduced even though bond stretch is greater at higher temperatures. There is a significant increase in stress level with increasing density. At faster rates of loading stress anisotropy increases. Deformation is mostly due to bond stretch and bond bending rather than overall shape and size. Stress levels increase with longer chain length. Cross-linkers beyond a critical value of functionality cause increased constraint on the motion of monomers and uniaxial stress developed increases. Stacking of chains also plays a dominant role in terms of excluded volume interactions. Low density, high temperature, low values of functionality of cross-linkers, and short chain length, facilitate chain uncoiling and chain slipping in crosslinked polymers. Uniaxial stress in linear polymers, on the other hand, is only mildly in uenced by temperature. Sinusoidal strain loading clearly reveals the viscoelastic nature of polymers. Internal structural parameters of the chains such as bond length, bond angle show hysteresis during loading and unloading. However, parameters representing overall size and shape of chains do not display any hysteresis. Small size magnetic particles and their small volume fractions in polymers show no signi cant e ect of applied external magnetic eld on anisotropic stress. Stress increases with lowering temperature, increasing density, decreasing volume fraction of magnetic particles, and increasing chain length

In recent years, a compound N-nitrosodimethylamine (NDMA), a probable human carcinogen, has been identified as an emerging disinfection by-product (DBP) since its formation and detection were linked to chlorine-based disinfection processes in several water utilities in the U.S. and Canada. Numerous organic nitrogen compounds present in water may impact the formation of NDMA during disinfection. Amine-based water treatment polymers used as coagulants and flocculants have been suggested as potential NDMA precursors due to the presence of amine functional groups in their structures, as well as the possible presence of dimethylamine (DMA) residues in polymer products. To minimize the potential risk of NDMA associated with water treatment polymers, the mechanisms of how the polymers behave as NDMA precursors and their contribution to the overall NDMA formation under actual water treatment conditions need to be elucidated. This research involved a systematic investigation to determine whether amine-based water treatment polymers contribute to NDMA formation under drinking water and wastewater treatment conditions, to probe the involved reaction mechanisms, and to develop strategies to minimize the polymers NDMA formation potential. The investigation included five research tasks: (1) General screening of NDMA formation potential of commonly used amine-based water treatment polymers, (2) NDMA formation from amine-based water treatment polymers under relevant water treatment conditions, (3) Probing the mechanisms of NDMA formation from polyamine and PolyDADMAC, (4) Effect of water treatment processes on NDMA formation from amine-based water treatment polymers, and (5) Developing strategies to reduce polymers NDMA formation potential. Direct chloramination or chlorination of high doses of polymers in deionized water at longer than typical contact time was used in the general screening of the NDMA formation potential of water treatment polymers and in the studies to identify reaction mechanisms. On the other hand, realistic dosages of chloramines and polymers and contact time were used in simulating representative water treatment conditions to evaluate the contribution of polymers to the overall NDMA formation in real systems. On the basis of the study results, strategies were developed to reduce the NDMA formation potential of amine-based water treatment polymers, which include modification of polymer structures and treatment parameters.

L'objectif de ce travail fut d'intensifier des procédés de polymérisation radicalaire par transfert d'atomes (ATRP) du méthacrylate de 2-(dimétylamino)éthyle (DMAEAMA) au moyen de technologies de microréaction (microréacteurs, micromélangeurs) et de paramètres de procédé (géométrie du réacteur, température, pression ... ).L'impact du prémélange sur les caractéristiques d'un copolymère statistique du DMAEMA et du méthacrylate de benzyle synthétisé dans des microréacteurs hélicoïdaux (CT) fut étudié en utilisant des principes différents de micromélange: bilamination, multilamination interdigitale (!MM) et jet d'impact. Des caractéristiques bien mieux contrôlées ont été obtenues avec !'IMM et l'intensification du procédé (Pl) a été clairement démontrée encomparaison d'un réacteur fermé ; en effet des masses molaires et conversions plus élevées ainsi que de plus faibles indices de polymolécularité (PDI) ont été obtenus pour des temps de passage inférieurs. Pour la production de PMADAME linéaire, le PI a également été réalisé par augmentation de la température et de la pression (jusqu'à 1 OO bars). Toutefois de trop hautes températures se sont avérées préjudiciables notamment pour de longs temps de passage. L'effet de l'augmentation du taux de cisaillement (via la longueur du réacteur) ne fut bénéfique qu'en régime dilué à un stade précoce de la réaction lorsque les masses molaires sont encore faibles. Comparés aux CT, un mélange interne favorisé par une technique d'inversion de flux s'est révélé être une stratégie très efficace pour réduire davantage le PDI et obtenir des masses molaires et conversions plus élevées. Des polymères branchés synthétisés en microréacteurs à inversion de flux (CFI) par ATRP en présence d'inimère présentèrent une structure plus ramifiée soulignant ainsi la supériorité des CFI sur les CT et réacteurs fermés en termes de PDI et d'efficacité de branchement. Considérant les caractéristiques des CFI, l'augmentation d'échelle des microréacteurs fut considérée par accroissement de leur diamètre. La productivité du procédé a été augmentée d'un facteur 4 tout en gardant un bon contrôle sur les caractéristiques macromoléculaires. Ainsi fut-il démontré que l'inversion de flux est un moyen très efficace pour contrebalancer l'effet négatif d'une augmentation du diamètre du microréacteur. / The aim of this work was to intensify Atom Transfer Radical polymerization (ATRP) processes for the production of DMAEMA-based (co)polymers by relying on microreaction technology tools (microreactor, micromixers) and process parameters (reactor geometry, temperature, pressure ... ). Impact of premixing on macromolecular characteristics of P(DMAEMA-co-BzMA) synthesized in coiled tube (CT) microreactors was studied using different micromixing principles: bilamination, interdigital multilamination (IMM) and impact jet.Better controlled characteristics were obtained with !MM and process intensification (PI) was clearly demonstrated in comparison with batch mode as higher molecular weights, increased monomer conversions and lower polydispersity indices (PDI) were obtained for lower residence times. For the production of linear PDAEMA, PI was also achieved by application of elevated temperature and pressure (up to 100 bars). However, high temperature was found to be detrimental for long residence times. Effect of increased shear rate (i.e. reactor length) was found only beneficial in dilute regime at the early stage of the polymerization reaction when molecular weights are low. ln comparison with CT reactors, internal mixing promoted by flow inversion technique was found to be quite an effective strategy to reduce further PDI and obtain higher molecular weights and monomer conversions. Branched polymers synthesized by self condensing vinyl copolymerization (SCVCP) adapted to ATRP in tubular coil flow inverter (CFI) microreactors exhibited higher branched structure highlighting the superiority of CFI microreactor over CT and batch reactors in terms of PD! and branching efficiency. Finally, considering such features of CFI, attempt was made to scale-up microreactors by increasing their diameter. lt was found that process throughput can be increased by more than a factor of 4 while keeping a good control over macromolecular characteristics. Thus itwas demonstrated that flow inversion is quite effective to counter balance the detrimental effect of an increase in microreactor diameter.

Hydrogel, semi-interpenetrating polymer network, poly(2-hydroxyethyl methacrylate), diffusion