Long-range surface plasmon-polaritons are transverse-magnetic polarized optical surface waves formed through the interaction of photons with free electrons at the surface of metal slabs or stripes. They play important roles in a variety of field such as integrated optics, amplifiers and lasers, optical sensing, modulation, etc. Due to their longer propagation length and deeper penetration depth compared to those of single-interface surface plasmon-polaritons, they have become increasingly promising in optical sensing. In sensing applications, it is necessary to reduce the noise level in order to obtain a lower detection limit. One way to achieve this is to use dual- or triple-output Mach-Zehnder interferometers so that the common perturbations among the outputs can be suppressed. The objective of this thesis is to provide deeper insights on the performances of dual- and triple-output Mach-Zehnder interferometers in thermo-optic and optical bulk sensing applications, theoretically and experimentally, and to demonstrate their ability to suppress common perturbations and lower the detection limit. On the theoretical side, the objective is approached by constructing a model for the transfer characteristic. For dual-output Mach-Zehnder interferometers, the plane-wave model is used to develop a general model for thermo-optic sensing and an unbalanced model for optical bulk sensing. For triple-output ones, local normal mode theory is used with modal analysis for the 3×3 coupler portion of the structure. Quantitative methods to analyze and compare different detection schemes are developed. The minimum detectable phase shift is determined for the case of thermo-optic sensing while the detection limit is determined for optical bulk sensing. On the experimental side, the objective is approached by providing a direct experimental demonstration of the transfer characteristics at an optimized operating wavelength for the coupler portion of the device, then comparing to theory. Time traces are carried out and various detection schemes are applied to suppress common perturbations among the outputs, and to improve the minimum detectable phase shift or the detection limit.

A novel process for the fabrication of Long Range Surface Plasmon Polariton (LRSPP) waveguide based biosensors is presented herein. The structure of the biosensor is comprised of Au stripe waveguide devices embedded in thick CYTOP claddings with a SiO2 solvent diffusion barrier and etch-stop layer. The SiO2 layer is introduced to improve the end quality of Au waveguide structures, which previously deformed during the deposit of the upper cladding process and to limit the over-etching of CYTOP to create micro-fluidic channels. The E-beam evaporation method is adapted to deposit a thin SiO2 on the bottom cladding of CYTOP. A new micro-fluidic design pattern is introduced. Micro-fluidic channels were created on selective Au waveguides through O2 plasma etching. The presented data and figures are refractive index measurements of different materials, thickness measurements, microscope images, and AFM images. Optical power cutback measurements were performed on fully CYTOP-cladded symmetric LRSPP waveguides. The end-fire coupling method was used to excite LRSPP modes with cleaved polarization maintaining (PM) fibre. The measured mode power attenuation (MPA) was 6.7 dB/mm after using index-matched liquid at input and output fibre-waveguide interfaces. The results were compared with the theoretical calculations and simulations. Poor coupling efficiency and scattering due to the SiO2 are suspected for off-target measurements.

A novel process for the fabrication of Long Range Surface Plasmon Polariton (LRSPP) waveguide based biosensors is presented herein. The structure of the biosensor is comprised of Au stripe waveguide devices embedded in thick CYTOP claddings with a SiO2 solvent diffusion barrier and etch-stop layer. The SiO2 layer is introduced to improve the end quality of Au waveguide structures, which previously deformed during the deposit of the upper cladding process and to limit the over-etching of CYTOP to create micro-fluidic channels. The E-beam evaporation method is adapted to deposit a thin SiO2 on the bottom cladding of CYTOP. A new micro-fluidic design pattern is introduced. Micro-fluidic channels were created on selective Au waveguides through O2 plasma etching. The presented data and figures are refractive index measurements of different materials, thickness measurements, microscope images, and AFM images. Optical power cutback measurements were performed on fully CYTOP-cladded symmetric LRSPP waveguides. The end-fire coupling method was used to excite LRSPP modes with cleaved polarization maintaining (PM) fibre. The measured mode power attenuation (MPA) was 6.7 dB/mm after using index-matched liquid at input and output fibre-waveguide interfaces. The results were compared with the theoretical calculations and simulations. Poor coupling efficiency and scattering due to the SiO2 are suspected for off-target measurements.

A novel process for the fabrication of Long Range Surface Plasmon Polariton (LRSPP) waveguide based biosensors is presented herein. The structure of the biosensor is comprised of Au stripe waveguide devices embedded in thick CYTOP claddings with a SiO2 solvent diffusion barrier and etch-stop layer. The SiO2 layer is introduced to improve the end quality of Au waveguide structures, which previously deformed during the deposit of the upper cladding process and to limit the over-etching of CYTOP to create micro-fluidic channels. The E-beam evaporation method is adapted to deposit a thin SiO2 on the bottom cladding of CYTOP. A new micro-fluidic design pattern is introduced. Micro-fluidic channels were created on selective Au waveguides through O2 plasma etching. The presented data and figures are refractive index measurements of different materials, thickness measurements, microscope images, and AFM images. Optical power cutback measurements were performed on fully CYTOP-cladded symmetric LRSPP waveguides. The end-fire coupling method was used to excite LRSPP modes with cleaved polarization maintaining (PM) fibre. The measured mode power attenuation (MPA) was 6.7 dB/mm after using index-matched liquid at input and output fibre-waveguide interfaces. The results were compared with the theoretical calculations and simulations. Poor coupling efficiency and scattering due to the SiO2 are suspected for off-target measurements.

A novel process for the fabrication of Long Range Surface Plasmon Polariton (LRSPP) waveguide based biosensors is presented herein. The structure of the biosensor is comprised of Au stripe waveguide devices embedded in thick CYTOP claddings with a SiO2 solvent diffusion barrier and etch-stop layer. The SiO2 layer is introduced to improve the end quality of Au waveguide structures, which previously deformed during the deposit of the upper cladding process and to limit the over-etching of CYTOP to create micro-fluidic channels. The E-beam evaporation method is adapted to deposit a thin SiO2 on the bottom cladding of CYTOP. A new micro-fluidic design pattern is introduced. Micro-fluidic channels were created on selective Au waveguides through O2 plasma etching. The presented data and figures are refractive index measurements of different materials, thickness measurements, microscope images, and AFM images. Optical power cutback measurements were performed on fully CYTOP-cladded symmetric LRSPP waveguides. The end-fire coupling method was used to excite LRSPP modes with cleaved polarization maintaining (PM) fibre. The measured mode power attenuation (MPA) was 6.7 dB/mm after using index-matched liquid at input and output fibre-waveguide interfaces. The results were compared with the theoretical calculations and simulations. Poor coupling efficiency and scattering due to the SiO2 are suspected for off-target measurements.