Existing containment models for a loss of coolant accident at many nuclear power plants were created in the 1970s using older computer technology and thermal hydraulic models which were available at that time. While conservative, these models may not present the detail necessary to identify conditions which may be used to produce additional design margin for the plant. After exploring containment and critical flow modeling, the basis for the use of GOTHIC in this analysis was established. A GOTHIC model was then created to simulate the loss of coolant accident results shown in an Updated Final Safety Analysis Report analysis for the North Anna Power Station. This model was used to examine the effects of increased nodalization in a subcompartment on the existing containment model. It is shown that adding multidimensional sub-nodes to areas of interest can provide valuable detail which was absent in the UFSAR model. Simulations are able to show the localized pressure spike around a LOCA pipe break that quickly dissipates, leaving significantly lower pressures in what was once an averaged, single, lumped-parameter node. This suggests that additional design margin may exist depending on where the pipe break is assumed to occur. / Master of Science

In nuclear power plants, a pipe break in the cooling line releases a jet that damages other equipment in containment, and is known as a loss of coolant accident (LOCA). This report specifically focuses on boiling water reactor (BWR) applications as a guide for future studies with pressurized water reactors (PWRs). This report presents a methodology for characterizing the jet such that, given a set of upstream conditions, the pressure field and damage potential of the jet can be predicted by an end user with a minimum of computation. The resultant model has many advantages over previous models in that it is easily calculated with knowledge readily available to plant operators and it provides new metrics that allow for a quick and intuitive understanding of the damage potential of the jet. / text

No description available.

A segurança de instalações nucleares é uma preocupação mundial que tem crescido, sobretudo, após o acidente nuclear de Fukushima. O estudo de acidentes em reatores nucleares de pesquisa tal como o Acidente de Perda de Refrigerante (APR), considerado por muitas vezes um acidente base de projeto, é importante para garantir a integridade da instalação. O APR pode levar ao descobrimento parcial ou total do núcleo do reator e, como condição de segurança, deve-se garantir que haja a remoção do calor de decaimento dos elementos combustíveis. Esse trabalho teve o objetivo de realizar experimentos de descobrimento parcial e total no Elemento Combustível Instrumentado (ECI), construído no Instituto de Pesquisas Energética e Nucleares (IPEN), a fim de estudar os possíveis APRs em reatores de pesquisa. Uma seção de testes, denominada STAR, foi projetada e construída para simular os APRs. O ECI foi irradiado no núcleo do reator IEA-R1 (IPEN) e inserido na STAR, que ficou totalmente imersa na piscina do reator. No ECI, foram instalados termopares para medição das temperaturas do revestimento e do fluido em várias posições axiais e radiais. Foram realizados experimentos para cinco níveis de descobrimento do ECI, um total e quatro parciais, em duas condições distintas de calor de decaimento. Na análise dos resultados, verificou-se que os casos de descobrimento total foram os mais críticos, ou seja, as temperaturas do revestimento foram as maiores quando comparadas com os casos de descobrimentos parciais. Adicionalmente, foi realizada a simulação numérica de dois experimentos com o código RELAP5, cujos resultados demonstraram ótima concordância com os dos níveis experimentais, e temperaturas maiores que as experimentais. As máximas temperaturas do revestimento alcançadas em todos os experimentos ficaram bem abaixo da temperatura de empolamento do combustível, que é de 500°C. Assim, a STAR provou ser um aparato experimental seguro e confiável para a realização de experimentos de perda de refrigerante. / The safety of nuclear facilities has been a growing global concern mainly after the Fukushima nuclear accident. Studies on nuclear research reactor accidents such as the Loss of Coolant Accident (LOCA), considered many times a design basis accident, are important for guaranteeing the integrity of the plant. A LOCA may lead to the partial or complete uncovering of the fuel assemblies and assured decay heat removal is a safety condition. This work aimed to perform partial and complete uncovering experiments in the Instrumented Fuel Assembly (IFA) designed at the Instituto de Pesquisas Energéticas e Nucleares (IPEN) in order to study possible LOCAs in research reactors. A test section for experimental simulation of Loss of Coolant Accident named STAR was designed and built. The IFA was irradiated in the IEA-R1 and installed in the STAR, which was totally immersed in the reactor pool. Thermocouples were installed in the IFA to measure the clad and fluid temperatures in several axial and radial positions. The experiments were carried out for five levels of uncovering of IFA, being one complete uncovering and four partial uncovering, in two different conditions of decay heat. In the results analysis was observed that the cases of complete uncovering of the IFA were the most critical ones, that is, those cases presented higher clad temperatures when compared with partial uncovering cases. Additionally, a numerical simulation of two experiments was carried out by using the RELAP 5 code. The numerical results showed an optimum agreement with the experimental levels results and greater than the experimental temperatures. The maximum clad temperatures reached in all experiments were quite below the fuel blister temperature, which is 500 °C. Therefore, the STAR has proven to be a safe and reliable experimental apparatus for conducting loss of coolant experiments.

A segurança de instalações nucleares é uma preocupação mundial que tem crescido, sobretudo, após o acidente nuclear de Fukushima. O estudo de acidentes em reatores nucleares de pesquisa tal como o Acidente de Perda de Refrigerante (APR), considerado por muitas vezes um acidente base de projeto, é importante para garantir a integridade da instalação. O APR pode levar ao descobrimento parcial ou total do núcleo do reator e, como condição de segurança, deve-se garantir que haja a remoção do calor de decaimento dos elementos combustíveis. Esse trabalho teve o objetivo de realizar experimentos de descobrimento parcial e total no Elemento Combustível Instrumentado (ECI), construído no Instituto de Pesquisas Energética e Nucleares (IPEN), a fim de estudar os possíveis APRs em reatores de pesquisa. Uma seção de testes, denominada STAR, foi projetada e construída para simular os APRs. O ECI foi irradiado no núcleo do reator IEA-R1 (IPEN) e inserido na STAR, que ficou totalmente imersa na piscina do reator. No ECI, foram instalados termopares para medição das temperaturas do revestimento e do fluido em várias posições axiais e radiais. Foram realizados experimentos para cinco níveis de descobrimento do ECI, um total e quatro parciais, em duas condições distintas de calor de decaimento. Na análise dos resultados, verificou-se que os casos de descobrimento total foram os mais críticos, ou seja, as temperaturas do revestimento foram as maiores quando comparadas com os casos de descobrimentos parciais. Adicionalmente, foi realizada a simulação numérica de dois experimentos com o código RELAP5, cujos resultados demonstraram ótima concordância com os dos níveis experimentais, e temperaturas maiores que as experimentais. As máximas temperaturas do revestimento alcançadas em todos os experimentos ficaram bem abaixo da temperatura de empolamento do combustível, que é de 500°C. Assim, a STAR provou ser um aparato experimental seguro e confiável para a realização de experimentos de perda de refrigerante. / The safety of nuclear facilities has been a growing global concern mainly after the Fukushima nuclear accident. Studies on nuclear research reactor accidents such as the Loss of Coolant Accident (LOCA), considered many times a design basis accident, are important for guaranteeing the integrity of the plant. A LOCA may lead to the partial or complete uncovering of the fuel assemblies and assured decay heat removal is a safety condition. This work aimed to perform partial and complete uncovering experiments in the Instrumented Fuel Assembly (IFA) designed at the Instituto de Pesquisas Energéticas e Nucleares (IPEN) in order to study possible LOCAs in research reactors. A test section for experimental simulation of Loss of Coolant Accident named STAR was designed and built. The IFA was irradiated in the IEA-R1 and installed in the STAR, which was totally immersed in the reactor pool. Thermocouples were installed in the IFA to measure the clad and fluid temperatures in several axial and radial positions. The experiments were carried out for five levels of uncovering of IFA, being one complete uncovering and four partial uncovering, in two different conditions of decay heat. In the results analysis was observed that the cases of complete uncovering of the IFA were the most critical ones, that is, those cases presented higher clad temperatures when compared with partial uncovering cases. Additionally, a numerical simulation of two experiments was carried out by using the RELAP 5 code. The numerical results showed an optimum agreement with the experimental levels results and greater than the experimental temperatures. The maximum clad temperatures reached in all experiments were quite below the fuel blister temperature, which is 500 °C. Therefore, the STAR has proven to be a safe and reliable experimental apparatus for conducting loss of coolant experiments.

L’un des accidents de dimensionnement d’un réacteur à eau pressurisée est l’Accident de Perte de Réfrigérant Primaire (APRP). L’évènement initiateur d’un tel accident est une brèche sur le circuit primaire du réacteur entrainant une perte d’inventaire en eau, et de ce fait conduit à un assèchement des assemblages combustibles. En conséquence, une augmentation considérable de la température surviendrait à l’intérieur du cœur du réacteur. Ainsi, les gaines de combustible peuvent éventuellement se déformer et des zones dites ballonnées apparaitre. Ces zones vont avoir un fort impact sur l’efficacité du refroidissement du cœur du réacteur. Pour contribuer à l’étude thermohydraulique d’un APRP, la présente thèse a pour but la caractérisation expérimentale des interactions entre un écoulement diphasique de vapeur/gouttes et une zone partiellement bouchée. Afin de reproduire un tel scénario, le banc expérimental thermohydraulique COLIBRI a été conçu. Plusieurs configurations géométriques de la zone ballonnée, caractéristiques d’un APRP, sont analysées (longueur et taux de bouchage associés au ballonnement). Afin de caractériser les échanges thermiques paroi/fluide ainsi que la dynamique des gouttes, des diagnostics optiques et thermiques sont utilisés : l’Anémométrie Phase Doppler (PDA) pour mesurer le diamètre et la vitesse des gouttes, la Fluorescence Induite par Laser (LIF) pour mesurer la température des gouttes et la Thermographie Infrarouge (IR) afin d’estimer le flux de chaleur extrait du tube par l’écoulement. En parallèle, une modélisation du problème a été développée afin d’obtenir une approche théorique de la capacité de refroidissement de l’écoulement diphasique. Le système d’équations décrivant la conservation de la masse, de la quantité de mouvement et de l’énergie permettra d’estimer l’impact respectif des différents mécanismes de transferts thermiques mis en jeu ainsi que l’évolution spatio-temporelle des paramètres thermohydrauliques / During a Loss of Coolant Accident (LOCA) in a Pressurized Water Reactor (PWR), caused by a break or a leakage on the primary circuit, partial or even complete drying of the fuel assemblies may occur. In these conditions, the fuel temperature increases, leading to a significant deformation and rupture of the fuel rod cladding. The cooling flow might be impaired, according to the size and distribution of the deformed zones within the fuel assemblies during the emergency cooling phase (Reflooding phase). To contribute to the thermalhydraulic study of the reflooding phase, this study aims to characterize experimentally the coolability of a representative deformed sub-channel by a steam-droplets flow under LOCA conditions. In order to reproduce such a scenario, the experimental thermal-hydraulic set-up COLIBRI was designed. Several geometrical blockage configurations are analyzed (Blockage ratios and axial lengths). Three measurement techniques are set up to follow the cooling transient phase of each experience: Phase Doppler Anemometry (PDA) in order to obtain both velocity and diameter of droplets, Laser Induced Fluorescence (LIF) to measure the mean droplet temperature and Infrared thermography to estimate the heat flux removed by the two-phase flow. Additionally, a one-dimensional mechanistic model, taking into account of the heat transfers mechanisms in the post-dry out region, is developed in order to analyze the experimental data and identify each one of the wall-to-fluid heat transfers (radiation with vapor and droplets, convection with vapor, evaporation, and droplet impact)

Dans le cadre des études visant à garantir l'intégrité de la gaine du crayon combustible, EDF est amené à caractériser la ductilité de la gaine après un Accident de Perte de Réfrigérant Primaire (APRP). La thèse porte sur la caractérisation du comportement à rupture des gaines en Zircaloy-4 détendu pour lesquels les conditions d'APRP ont été simulées en laboratoire par une oxydation à haute température suivie d'un refroidissement. L'oxydation est effectuée à 1100°C et à 1200°C pour différentes durées ce qui conduit à des niveaux d'oxydation de 3% à 30% d'ECR (Equivalent Cladding Reacted). Deux types de refroidissement sont mis en oeuvre : la trempe à l'eau et le refroidissement à l'air. Les gaines oxydées comportent deux couches fragiles, la couche de zircone externe ZrO2 et la couche α(O), et une couche présentant une ductilité résiduelle, la couche ex-β.Les gaines oxydées ont fait l'objet de caractérisations en microscope optique, par analyse à la microsonde et par nano-indentation. Une corrélation entre la teneur en oxygène et la nano-dureté et le module d'Young a été proposée.L'essai Expansion due à la Compression (EDC) a été développé avec une instrumentation par stéréo-corrélation d'images puis a été utilisé pour caractériser le comportement mécanique des gaines oxydées. Le comportement des gaines oxydées a été étudié à partir de l'analyse des courbes macroscopiques de l'essai EDC et à partir des observations des échantillons rompus ou pré-déformés.Un scénario de rupture des gaines oxydées a été proposé. Ce scénario a été validé d'une part par la réalisation d'essais sur gaines sablées ne comportant que la couche ex-β et d'autre part par la modélisation de l'essai par la méthode des éléments finis. Un critère de rupture des gaines oxydées a par ailleurs été établi. La modélisation du comportement et le critère de rupture proposés ont été validés par la modélisation des essais de compression d'anneau. / In order to guarantee the integrity of nuclear fuel rod cladding, it is necessary for EDF to characterize the ductility of cladding after a Loss of Coolant Accident (LOCA). The thesis is about the characterization of the fracture behavior of cold-worked stress-relieved Zircaloy-4 claddings which have undergone LOCA conditions simulated in laboratory by a high temperature oxidation followed by a cooling. The high temperature oxidation is carried out at 1100°C and 1200°C with different times, which leads to different oxidation levels varying from 3% to 30% ECR (Equivalent Cladding Reacted). The high temperature oxidation is followed by two types of cooling: water quench and air cooling. The oxidized claddings contain two fragile layers - the outer zirconium oxide ZrO2 layer and the middle α(O) layer, and a layer which can have residual ductility - the inner ex-β layer.Characterizations by means of optical microscopy, electron probe micro analysis and nano-indentation have been carried out on the oxidized claddings. A correlation between the oxygen concentration and the nano-hardness and the Young's modulus has been proposed.The Expansion Due to Compression (EDC) test has been developed with an instrumentation of stereo digital image correlation, and then used to characterize the mechanical behavior of the oxidized claddings. The behavior of the oxidized claddings has been studied via macroscopic EDC test curves and observations of fractured or pre-deformed test samples.A fracture scenario of the oxidized claddings has been proposed. The fracture scenario has then been validated via EDC tests on oxidized claddings whose ZrO2 and α(O) layers have been removed, and via finite element modeling of EDC tests. Moreover, a fracture criterion has been established. The mechanical behavior modeling and the proposed fracture criterion have been validated by modeling of ring compression test.

In the event of hypothetical accident scenarios in PWR, emergency strategies have to be mapped out, in order to guarantee the reliable removal of decay heat from the reactor core, also in case of component breakdown. One essential passive heat removal mechanism is the reflux condensation cooling mode. This mode can appear for instance during a small break loss-of-coolant-accident (LOCA) or because of loss of residual heat removal (RHR) system during mid loop operation at plant outage after the reactor shutdown. In the scenario of a loss-of-coolant-accident (LOCA), which is caused by the leakage at any location in the primary circuit, it is considered that the reactor will be depressurized and vaporization will take place, thereby creating steam in the PWR primary side. Should this lead to ¿reflux condensation¿, which may be a favorable event progression, the generated steam will flow to the steam generator through the hot leg. This steam will condense in the steam generator and the condensate will flow back through the hot leg to the reactor, resulting in counter-current steam/water flow. In some scenarios, the success of core cooling depends on the behaviour of this counter-current flow. Over several decades, a number of experimental and theoretical studies of counter-current gas¿liquid two-phase flow have been carried out to understand the fundamental aspect of the flooding mechanism and to prove practical knowledge for the safety design of nuclear reactors. Starting from the pioneering paper of Wallis (1961), extensive CCFL data have been accumulated from experimental studies dealing with a diverse array of conditions A one-dimensional two field model was developed in order to predict the counter-current steam and liquid flow that results under certain conditions in the cold leg of a PWR when a SBLOCA (small break loss of coolant accident) in the hot leg is produced. The counter-current model that has been developed can predict the pressure, temperature, velocity profiles for both phases, also by taking into account the HPI injection system in the cold leg under a counter-current flow scenario in the cold leg. This computer code predicts this scenario by solving the mass, momentum and energy conservation equations for the liquid and for the steam separately, and linking them by using the interfacial and at the steam wall condensation and heat transfer, and the interfacial friction as the closure relations. The convective terms which appear in the discretization of the mass and energy conservation equations, were evaluated using the ULTIMATE-SOU (second order upwinding) method. For the momentum equation convective terms the ULTIMATE-QUICKEST method was used. The steam-water counter-current developed code has been validated using some experimental data extracted from some previously published articles about the direct condensation phenomenon for stratified two-phase flow and experimental data from the LAOKOON experimental facility at the Technical University of Munich. / Romero Hamers, A. (2014). STUDY OF THE THERMAL STRATIFICATION IN PWR REACTORS AND THE PTS (PRESSURIZED THERMAL SHOCK) PHENOMENON [Tesis doctoral]. Editorial Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/36536 / Alfresco

This work seeks to illustrate the potential benefits afforded by implementing aspects of fluid dynamics, especially the latest computational fluid dynamics (CFD) modeling approach, through numerical experimentation and the traditional discipline of physical experimentation to improve the calibration of the severe reactor accident analysis code, MELCOR, in one of several spent fuel pool (SFP) complete loss-of-coolant accident (LOCA) scenarios. While the scope of experimental work performed by Sandia National Laboratories (SNL) extends well beyond that which is reasonably addressed by our allotted resources and computational time in accordance with initial project allocations to complete the report, these simulated case trials produced a significant array of supplementary high-fidelity solutions and hydraulic flow-field data in support of SNL research objectives. Results contained herein show FLUENT CFD model representations of a 9x9 BWR fuel assembly in conditions corresponding to a complete loss-of-coolant accident scenario. In addition to the CFD model developments, a MATLAB based control-volume model was constructed to independently assess the 9x9 BWR fuel assembly under similar accident scenarios. The data produced from this work show that FLUENT CFD models are capable of resolving complex flow fields within a BWR fuel assembly in the realm of buoyancy-induced mass flow rates and that characteristic hydraulic parameters from such CFD simulations (or physical experiments) are reasonably employed in corresponding constitutive correlations for developing simplified numerical models of comparable solution accuracy. / text