The recent pollution norms have brought a strong emphasis on the reduction of diesel engine emissions. Low temperature combustion technology such as premixed compression ignition (PCI) has the capability to significantly and simultaneously reduce nitric oxides (NOx) and particulate matter (PM), thus meeting these specific pollution norms. There has been, however, observed loss in fuel conversion efficiency in some cases. This study analyzes how energy transfer and brake fuel conversion efficiency alter with (or are affected by) injection timings and exhaust gas recirculation (EGR) rate. The study is conducted for PCI combustion for four injection timings of 9°, 12°, 15° and 18° before top dead center (BTDC) and for four exhaust gas recirculation (EGR) rates of 39%, 40%, 41% and 42%. The data is collected from the experimental apparatus located in General Motors Collaborative Research Laboratory at the University of Michigan. The heat release is calculated to obtain various in-cylinder energy transfers. The brake fuel conversion efficiency decreases with an increase in EGR. The decrease in the brake fuel conversion efficiency is due to the decrease in work output. This decrease is due to an increase in the pumping work and an increase in friction and decrease in gross indicated work. The decrease in the combustion efficiency is because of the increased formation of unburnt products due to increased ignition delay caused by the application of EGR and decreasing air-fuel (A/F) ratio. A definite trend is not obtained for the contribution of heat transfer to the total energy distribution. However the total heat transfer decreases with retardation of injection timing because of decreasing combustion temperature. As the injection timing is retarded, the brake fuel conversion efficiency is found to decrease. This decrease is because of a decrease in net work output. This is because the time available for utilization of the energy released is less because of late combustion. The total heat transfer decreases with retardation of injection timing because of decreasing combustion temperature. The contribution of heat transfer to the total energy distribution decreases with increase in EGR.

The recent pollution norms have brought a strong emphasis on the reduction of diesel engine emissions. Low temperature combustion technology such as premixed compression ignition (PCI) has the capability to significantly and simultaneously reduce nitric oxides (NOx) and particulate matter (PM), thus meeting these specific pollution norms. There has been, however, observed loss in fuel conversion efficiency in some cases. This study analyzes how energy transfer and brake fuel conversion efficiency alter with (or are affected by) injection timings and exhaust gas recirculation (EGR) rate. The study is conducted for PCI combustion for four injection timings of 9°, 12°, 15° and 18° before top dead center (BTDC) and for four exhaust gas recirculation (EGR) rates of 39%, 40%, 41% and 42%. The data is collected from the experimental apparatus located in General Motors Collaborative Research Laboratory at the University of Michigan. The heat release is calculated to obtain various in-cylinder energy transfers. The brake fuel conversion efficiency decreases with an increase in EGR. The decrease in the brake fuel conversion efficiency is due to the decrease in work output. This decrease is due to an increase in the pumping work and an increase in friction and decrease in gross indicated work. The decrease in the combustion efficiency is because of the increased formation of unburnt products due to increased ignition delay caused by the application of EGR and decreasing air-fuel (A/F) ratio. A definite trend is not obtained for the contribution of heat transfer to the total energy distribution. However the total heat transfer decreases with retardation of injection timing because of decreasing combustion temperature. As the injection timing is retarded, the brake fuel conversion efficiency is found to decrease. This decrease is because of a decrease in net work output. This is because the time available for utilization of the energy released is less because of late combustion. The total heat transfer decreases with retardation of injection timing because of decreasing combustion temperature. The contribution of heat transfer to the total energy distribution decreases with increase in EGR.

A detailed second law analysis of dual fuel LTC is not yet available in the open literature even though dual fuel low temperature combustion (LTC) has been studied before. To address this gap, a previously validated, closed-cycle, multi-zone, simulation of diesel-natural gas dual fuel LTC was used to perform a second law analysis. In the current study, a 2.4-liter single-cylinder research engine operating at a nominal load of 6 bar BMEP and 1700 rpm was used. Zone-wise thermodynamic irreversibilities as well as total cumulative entropy generated and lost available work over the closed cycle were quantified. Subsequently, two convenient second-law parameters were defined: (1) the “lost available indicated mean effective pressure” (LAIMEP), which can be interpreted as an engine-size-normalized measure of available work that is lost due to thermodynamic irreversibilities (analogous to the relationship between indicated mean effective pressure and indicated work); (2) fuel conversion irreversibility (FCI), which is defined as the ratio of lost available work to total fuel chemical energy input. Finally, parametric studies were performed to quantify the effects of diesel start of injection, intake manifold temperature, and intake boost pressure on LAIMEP and FCI. The results show that significant entropy generation occurred in the flame zone (52-61 percent) and the burned zone (31-39 percent) while packets account for less than 6 percent of the overall irreversibilities. Parametric studies showed LAIMEPs in the range of 645-768 kPa and FCIs in the range of 32.8-39.2 percent at different engine operating conditions. Although the present study focused on dual fuel LTC, the conceptual definitions of LAIMEP and FCI are generally applicable for comparing the thermodynamic irreversibilities of IC engines of any size and operating on any combustion strategy.

Low temperature combustion (LTC) is an appealing new method of combustion that promises low nitric oxides and soot emissions while maintaining or improving on engine performance. The three main points of this study were to develop and validate an engine model in GT-Power capable of implementing LTC, to study parametrically exhaust gas recirculation (EGR) and injection timing effects on performance and emissions, and to investigate methods to decrease pressure rise rates during LTC operation. The model was validated at nine different operating points, 3 speeds and 3 loads, while the parametric studies were conducted on 6 of the 9 operating points, 3 speeds and 2 loads. The model consists of sections that include: cylinders, ports, intake and exhaust manifolds, EGR system, and turbocharger. For this model, GT-Power calculates the combustion using a multi-zone, quasi-dimensional model and a knock-induced combustion model. The main difference between them is that the multi-zone model is directly injected while the knock model is port injected. A variety of sub models calculate the fluid flow and heat transfer. A parametric study varying the EGR and the injection timing to determine the optimal combination was conducted using the multi-zone model while a parametric study that just varies EGR is carried out using the knock model. The first parametric study showed that the optimal EGR and injection timing combination for the low loads occurred at high levels of EGR (60 percent) and advanced injection timings (30 to 40 crank angle degrees before top dead center). The optimal EGR and injection timing combination for the high loads occurred at low levels of EGR (30 percent to 40 percent) and retarded injection timings (7.5 to 5 crank angle degrees before top dead center). The knock model determined that the ideal EGR ratio for homogeneous charge compression ignition (HCCI) operation varied from 30 percent to 45 percent, depending on the operating condition. Three methods were investigated as possible ways to reduce pressure rise rates during LTC operation. The only feasible method was the multiple injection strategy which provided dramatically reduced pressure rise rates across all EGR levels and injection timings.

As global focus shifts towards the health and conservation of the planet, greater importance is placed upon the hazardous emissions of our fossil fuels, as well as their finite supply. These two areas remain intense topics of research in order to reduce green house gas emissions and increase the fuel efficiency of our vehicles. A particular solution to this problem is the diesel engine, with its inherently fuel-lean combustion, which gives rise to low CO2 production and higher efficiencies than its gasoline counterpart. Diesel engines, however, typically exhibit higher nitrogen oxides (NOx [NOx = NO NO2, where NO is nitric oxide and NO2 is nitrogen dioxide]) and soot. There exists the possibility to simultaneously reduce both emissions with the application of low temperature diesel combustion (LTC). While exhibiting great characteristics in simultaneous reductions in nitrogen oxides and soot, LTC faces challenges with higher carbon monoxide (CO) and hydrocarbon (HC) emissions, as well as penalties in fuel efficiency. The following study examines the characteristics of LTC which contribute to the differences in emissions and efficiency compared to typical conventional diesel combustion. More specifically, key engine parameters which are used to enable LTC, such as EGR and fuel pressure are swept through a full range to determine their effects on each combustion regime. Analysis will focus on comparing both combustion regimes to determine how exhaust gas recirculation (EGR) and fuel pressure relate to lowering NO and smoke concentrations, and how these relate to a penalty in fuel efficiency. This study finds that the application of LTC is able to realize a 99 percent reduction in NO while simultaneously reducing smoke by 17 percent compared to the conventional combustion counterpart. Through a sweep increasing EGR, LTC is able to defeat the typical soot – NO tradeoff; however, brake fuel conversion efficiency decreases 6.8 percent for LTC, while conventional combustion realizes a 4 percent increase in efficiency. The sweep of increasing fuel pressure confirms typical increases in NO and decreases in smoke for both LTC and conventional combustion; however, brake fuel conversion efficiency increases 2.3 percent for LTC and drops 4 percent for conventional combustion.

When a gas undergoes an exothermic reaction in a closed vessel, spatial temperature gradients can develop. If these gradients become sufficiently large, the resulting buoyancy forces will move the gas, i.e. there is natural convection. The nature of the resulting flow is determined by the Rayleigh number, Ra = (β g ΔT L^3) / (κ ν). The evolution of such a system will depend on the interactions of natural convection, diffusion of both heat and chemical species, and chemical reaction. This study is concerned with a gas-phase system undergoing Sal'nikov's reaction: P → A → B, in the presence of natural convection. This kinetic scheme is used as a simplified representation of a cool flame, which is a feature of the low temperature combustion of a hydrocarbon vapour. Sal'nikov's reaction is one of the simplest to display thermokinetic oscillations, such as those seen in cool flames. The behaviour of Sal'nikov's reaction in the presence of natural convection was investigated using a combination of analytical and numerical techniques. First, a numerical model was developed to compute the temperature, velocity and concentrations when a simple exothermic reaction occurs in a spherical batch reactor, the results of which could be compared with previous experimental measurements. Subsequently, a scaling analysis of Sal'nikov's reaction proceeding in a spherical reactor was performed. This yielded significant insight into the general behaviour of this and similar systems. The forms of the analytical scales were confirmed through comparison with the results from numerical simulations. These scales were used to predict how the system responds to changes in certain key process variables, such as the pressure and the size of the reactor. It was shown that the behaviour of this system is governed by the ratios of the characteristic timescales for diffusion, reaction and natural convection. These ratios were used to define a regime diagram describing the system. The behaviour in different parts of this regime diagram was characterised and regions in which oscillations occur were identified.

The present manuscript discusses the performance and emission benefits due to two diesel injections in diesel-ignited methane dual fuel Low Temperature Combustion (LTC). A Single Cylinder Research Engine (SCRE) adapted for diesel-ignited methane dual fuelling was operated at 1500 rev/min and 5 bar BMEP with 1.5 bar intake manifold pressure. The first injection was fixed at 310 CAD. A 2nd injection sweep timing was performed to determine the best 2nd injection timing (as 375 CAD) at a fixed Percentage Energy Substitution (PES 75%). The motivation to use a second late injection ATDC was to oxidize Unburnt Hydrocarbons (HC) generated from the dual fuel combustion of first injection. Finally, an injection pressure sweep (550-1300 bar) helped achieve simultaneous reduction of HC (56%) and CO (43%) emissions accompanied with increased IFCE (10%) and combustion efficiency (12%) w.r.t. the baseline single injection (at 310 CAD) of dual fuel LTC.

Natural gas is currently an attractive substitute for diesel fuel in the Heavy-Duty (HD) diesel transportation sector. This is primarily attributed to its cost effectiveness, but also its ability to reduce the amount of CO2 and harmful engine pollutants emitted into the atmosphere. Lean-burn dual-fuel engines substitute natural gas in place of diesel but typically suffer from high engine-out methane (CH4) emissions, particularly under low load operation. In response to this issue, this work set out to improve upon the efficiency and emissions of a lean-burn dual-fuel combustion system in an HD diesel/natural gas engine. Thermodynamic experimental engine testing was performed at various steady-state operating points in order to identify the most effective methods and technologies for improving emissions and efficiency. Low Temperature Combustion (LTC) along with several valvetrain and injection strategies were evaluated for benefits, with special attention paid to low load operating conditions. LTC was proven to be a useful method for decreasing methane emissions while simultaneously improving engine efficiency. The benefits of LTC were a function of load with the greatest advantages experienced under medium load operation. Additionally, the low load strategies tested were determined to be effective techniques for reducing methane emissions and could possibly extend the dual-fuel operating regime to lighter load conditions. Overall, no operating condition tested throughout the engine map resulted in a brake engine-out methane emissions level of less than 0.5 g/kWh at gas substitutions greater than approximately 75%. It is suggested that the limits of this particular lean-burn dual-fuel design were reached, and that it would likely require improvements to either the combustion system or exhaust after-treatment if Euro VI emissions levels for methane were to be achieved.

Internal combustion engines have dealt with increasingly restricted emissions requirements. After-treatment devices are successful in bringing emissions into compliance, but in-cylinder combustion control can reduce their burden by reducing engine out emissions. For example, oxides of nitrogen (NOx) are diesel combustion exhaust species that are notoriously difficult to remove by after-treatment. In-cylinder conditions can be controlled for low levels of NOx, but this produces high levels of soot potentially leading to increased particulate matter (PM). The simultaneous reduction of NOx and PM can be realized through a combustion process known as low temperature combustion (LTC). In this study, the typical definition of LTC as the defeat of the inverse relationship between soot and NOx is not applicable as a return to the soot-NOx tradeoff is observed with increasing exhaust gas recirculation (EGR). It is postulated that this effect is the result of an increase in the hot ignition equivalence ratio, moving the combustion event into a slightly higher soot formation region. This is important because a simple emissions based definition of LTC is no longer helpful. In this study, the manifestation of LTC in the calculated heat release profile is investigated. The conditions classified as LTC undergo a two-stage ignition process. Two-stage ignition is characterized by an initial cool-flame reaction followed by typical hot ignition. In traditional combustion conditions, the ignition is fast enough that a cool-flame is not observed. By controlling initial conditions (pressure, temperature, and composition), the creation and duration of the cool-flame event is predictable. Further, the effect that injection timing and the exhaust gas recirculation level have on the controlling factors of the cool-flame reaction is well correlated to the duration of the cool-flame event. These two results allow the postulation that the presence of a sufficiently long cool-flame reaction indicates a combustion event that can be classified as low temperature combustion. A potential method for identifying low temperature combustion events using only the rate of heat release profile is theorized. This study employed high levels of EGR and late injection timing to realize the LTC mode of ordinary petroleum diesel fuel. Under these conditions, and based on a 90 percent reduction in nitric oxide and no increase in smoke output relative to the chosen baseline condition, a two part criteria is developed that identifies the LTC classified conditions. The criteria are as follow: the combustion event of conventional petroleum diesel fuel must show a two-stage ignition process; the first stage (cool-flame reaction) must consume at least 2 percent of the normalized fuel energy before the hot ignition commences.

The efficiency of an internal combustion (IC) engine is governed by the thermodynamic cycle underpinning its operation. The thermodynamic efficiency of these devices is primarily determined by the temperature gradient created during the compression process. The final conversion efficiency also known as brake thermal efficiency (BTE) of IC engines, however, also depend on other processes associated with its operation. BTE is a product of the combustion, thermodynamic, gas-exchange, and mechanical efficiencies. The improvement of BTE through maximation of any one of the four efficiencies is reduced by its implication of the other three. Split-cycle engine provides an alternative method of improving the engine efficiency through over-expansion of combustion gases by transferring it to a cylinder of greater volume. The operation of split-cycle engines is based on either the Brayton or the Atkinson Cycles. Atkinson Cycle has been demonstrated in IC engines without the split-cycle architecture but is limited by the reduced energy density. Double Compression Expansion Engine (DCEE) provides a method of accomplishing the Atkinson Cycle without the constraints faced in conventional engine architectures. DCEE splits the compression and expansion processes in a vertical manner that enables the use of larger cylinder volumes for over-expansion as well as first-stage compression without much friction penalties. The present thesis explores the thermodynamic cycle of this novel engine architecture using well-validated 1-dimensional engine models solving for gas-exchange, real gas properties, and heat transfer provided in the GT-Power software tool. The effect of compression ratio, rate of heat addition, sensitivity to design and modeling parameters was assessed and contrasted against conventional engine architecture. The synergies of combining low-temperature combustion (LTC) concepts with DCEE was investigated using simulation and experimental data. DCEE relaxes many constraints placed the operation of an engine in Homogenous Charge Compression Ignition (HCCI) mode. The limitations of adopting Partially Premixed Combustion (PPC) concept is also alleviated by the DCEE concept. BTE improvement of above 10% points is achievable through the DCEE concept along with possibility to achieve very low emissions through use of LTC concepts and new after-treatment methods uniquely available to the DCEE.