This thesis focuses on the design of new high pressure injection system application on diesel engine. The design came from company Zetor’s demands. For this application was chosen system Common Rail supplied by company Bosch. Assignment was separated into several tasks. Research of suitable components for low pressure section, design of waste system and high pressure injection tubes design including injector clamping. Due to injectors used in this system was necessary to redesign cover for valves and even new system to lead wires from outside of the engine to injectors. Injector is attached by screw connection, which is composed from screw and clamping jaw. These parts are subjected to an analytic calculations. Clamping jaw of injector is even subjected to a FEM analysis, which focuses on fatigue life. Finally, the drawings were documented.

Analytical methods or implicit finite element method (FEM) with beam elements to model straightened bar were used to analyze straightening process in multi-staggered cross-roll straighteners up to now. These are effective but require certain simplifications. Aim of this thesis is to create an explicit FEM model allowing usage of solid elements for circular bar without disproportional increase of computational time. This may lead to deeper understanding of the straightening process. The model is to be verified using straightening tables and then used to quantify influence of rollers configuration on results of the straightening process.

Tato diplomová práce se zabývá elektromagnetickou analýzou a modelováním asynchronního stroje s plným rotorem. Tato práce tedy zahrnuje literární rešerši na téma vysokootáčkových elektrických strojů s porovnáním s klasickými elektrickými stroji s převodovkou a popisem jejich výhod či nevýhod, rozdělení vysokootáčkových elektrických strojů s plnými rotory a srovnání jejich výhod či nevýhod, kde se tato práce nejvíce soustřeďuje na vysokootáčkové asynchronní stroje s plnými rotory a jejich použití v průmyslu. Dále se tato práce zabývá metodami výpočtu elektrických asynchronních strojů s plnými rotory. Proto jsou zde uvedeny a popsány metody výpočtu stroje mezi které patří analytické metody i metoda konečných prvků. Vzhledem k povaze elektrických strojů s plnými rotory je hlavně kladen důraz v této práci na výpočet stroje pomocí metody konečných prvků ve 2D prostoru s využitím korekčních činitelů konců plných rotorů, které jsou zde velmi detailně popsány a rozděleny. Na základě dostupné literatury je vypočítaný elektrický stroj s plným rotorem pomocí MKP analýzy. Elektromagnetický výpočet stroje je automatizován pomocí skriptu vytvořeného v Pythonu. Dalším hlavním cílem této práce je popis tzv. náhradních modelů, uvedení jejich výhod či nevýhod, použití v jiných průmyslových odvětvích a hlavně použití náhradních modelů na elektrický stroj s plným rotorem. S využitím náhradních modelů je dále optimalizovaný vybraný asynchronní stroj s plným rotorem a to pomocí programů SymSpace a Optimizer. Pro samotnou optimalizaci byly uvažovány 3 návrhy stroje, které byly na závěr mezi sebou porovnány a to hlavně z hlediska jejich elektromagnetického výkonu.

This thesis is focusing on the use of the finite element method (FEM) in program environment of Autodesk Inventor Professional (AIP) 2010. For the analysis of the components or assemblies with FEM serves the Strength analysis module of the AIP 2010, whose environment and functions are detailed in this thesis. At the conclusion practical examples of modal and static analysis on the synchronous generator rotor model are demonstrated including a brief evaluation of the results.

The theme of this thesis is the design and verification of the auxiliary winding to supply the voltage regulator of the synchronous generator. The synchronous generator for which the auxiliary winding proposed is three-phase, low voltage with double layer random wound stator winding. The generator excitation is brushless with auxiliary rotating exciter. The auxiliary winding is designed for placement in the stator teeth, along with the main winding. The sizing of the auxiliary winding is derived from the power requirements the voltage regulator. Draft winding is validated analytical calculation and finite element method (FEM). The auxiliary winding has been implemented in the production of the generator. The Features of the auxiliary winding have been verified by measuring the by electrical testing room and the test results are evaluated.

This diploma thesis deals with problem of design and calculation of membrane structure of stadium roof. This is a complex engineering problem, which includes many partial problems: finding of initial form of membrane, statically and architecturally suitable arrangement of catenaries, economical solution of boundary conditions (foundations). All components affect each other and cannot be dealt without mutual coordination. It always greatly depends on the experience and intuition of engineer who design such structure. Task which cannot be resolved according to the theory of the first order. Equilibrium forces on the deformed structure, which in many projected structures gives satisfactory results, did not correspond to reality. It is therefore necessary to consider equilibrium of forces on the deformed structure according to the theory of large deformations. Diploma thesis was entered with regard to the intention of the companies Ing. Software Dlubal s.r.o. and FEM consulting s.r.o., working together to develop software RFEM. These companies plan to complement this program system with a module MEMBRANE for searching of initial shapes of membrane structures. This work is a contribution to the creation of this module.

They analyzed the various factors affecting the design or evaluation of structural glass. Within evaluation of structural glass element is checked selected concepts of linear elastic fracture mechanics. For modeling is used programme system ANSYS based finite element method. The results are compared with the analytical solution.

Diploma thesis is fucused on strength calculation of the heat exchanger according to ČSN EN 13 445. Introductory part introduce problems with the design of heat exchangers. In other parts there are a strength calculation of the heat exchanger according to ČSN EN 13 445, the results of the analysis with their appreciation. Annexes included output logs from the program Sant 'Ambrogio, and drawings documentation.

This work is focused on the stress-strain analysis of a cutting tool. At the beginning, the study of available literature and scientific articles relating the topic is carried out. The solution of stresses and strains in whole real system has been carried out based on the computational simulation using the finite element method (FEM). The work contains a detailed description of the creation of the computational model. Model of geometry of the system has been created in the SolidWorks program. Computational simulation including the solution was implemented in the ANSYS Workbench program as well as in the classical environment of ANSYS 12.0. This work includes the presentation of results and subsequent stress-strain analysis of the cutting tool. Last part of this work deals with the modal analysis and harmonic analysis of cutting tools made in classical environment of ANSYS program.

The master thesis deals with thermal hydraulic design and strength design of a heat exchanger with “U” tube bundle inside of a shell. The first chapter introduces general design issues of the heat exchangers. The following chapter describes thermal hydraulic design created in software Maple 16.0 by using Kern’s method and the method of Bell-Delaware. HTRI software was used for the control of thermal hydraulic design correctness. To check critical locations of fluid flow in space between the tubes, the CFD model was created at ANSYS Fluent 14.0 software. Accuracy of strength design was verifying by Sant’ Ambrogio software in accordance with ČSN EN 13 445 standards. The last chapter concerns with FEM analysis. According to standards ČSN EN 13 445 the design by analysis namely method based on stress categories were used for the strength analysis of nozzle.