A compact, frequency-reconfigurable filtenna with sharp out-of-band rejection in both its wideband and continuously tunable narrowband states is presented. It is intended for use in cognitive radio applications. The wideband state is the sensing state and operationally covers 2.35-4.98 GHz. The narrowband states are intended to cover communications within the 3.05-4.39 GHz range, which completely covers the Worldwide Interoperability for Microwave Access (WiMAX) band and the satellite communications C-band. A p-i-n diode is employed to switch between these wide and narrowband operational states. Two varactor diodes are used to shift the operational frequencies continuously among the narrowband states. The filtenna consists of a funnel-shaped monopole augmented with a reconfigurable filter; it has a compact electrical size: 0.235 lambda(L) x 0.392 lambda(L), where the wavelength lambda(L) corresponds to the lower bound of its operational frequencies. The measured reflection coefficients, radiation patterns, and realized gains for both operational states are in good agreement with their simulated values.

No / A miniaturized modified planar inverted-F antenna (PIFA) is presented and experimentally studied. This antenna consists of a planar rectangular monopole top-loaded with a rectangular patch attached to two rectangular plates, one shorted to the ground and the other suspended, both placed at the optimum distance on each side of the planar monopole. The fabricated antenna prototype had a measured impedance bandwidth of 125%, covering 3 to 13GHz for reflection coefficient better than -10 dB. The radiator size was 20 x 10 x 7.5 mm(3), making it electrically small over most of the band and suitable for incorporation in mobile devices. The radiation patterns and gains of this antenna have been cross-validated numerically and experimentally and confirm that this antenna has adequate characteristics for short range ultra-wideband wireless applications.

A novel printed diversity monopole antenna is presented for WiFi/WiMAX applications. The antenna comprises two crescent shaped radiators placed symmetrically with respect to a defected ground plane and a neutralization lines is connected between them to achieve good impedance matching and low mutual coupling. Theoretical and experimental characteristics are illustrated for this antenna, which achieves an impedance bandwidth of 54.5% (over 2.4-4.2 GHz), with a reflection coefficient <;-10 dB and mutual coupling <;-17 dB. An acceptable agreement is obtained for the computed and measured gain, radiation patterns, envelope correlation coefficient, and channel capacity loss. These characteristics demonstrate that the proposed antenna is an attractive candidate for multiple-input multiple-output portable or mobile devices

In this dissertation, a variety of multiband communication device antennas using the coupling-feed mechanism are presented. The coupling feed contributes additional capacitance to the antenna¡¦s input impedance which shows a high inductive component for the traditional case of using a direct feed. In the first and second antenna designs, with the coupling feed, the high input inductance of the antenna is effectively compensated. This behavior leads to a dual-resonance excitation for the lower band of the antenna. Two wide operating bands are achieved, allowing the antenna¡¦s lower and upper bands to easily cover GSM850/900 and GSM1800/1900/UMTS operation. For the last two antenna designs, owing to the coupling feed, the very large input impedance seen at antenna¡¦s lower band is greatly decreased and results in successful excitation of the one-eighth wavelength (£f/8) mode of the antenna. The specific absorption rate and hearing aid compatibility results for these mobile phone antennas are also analyzed. The effects of presence of the user¡¦s hand on the laptop computer antenna performance are also studied in this dissertation.

This thesis deals with the design of omnidirectional monopole antennas. Using the parabolic reflector and the directors, the directional characteristics of monopole antennas are modified. This directional antenna, together with the omnidirectional antenna, examines the effect of various materials, the emission characteristics and the input reflection factor, near the antennas. These antennas are made of 3D textile, measured in anechoic chamber and compared to the designed antennas. At the end of the thesis is the summary and evaluation of the result.

No / This article presents a printed crescent-shaped monopole MIMO diversity antenna for wireless communications. The port-to-port isolation is increased by introducing an I-shaped conductor symmetrically between the two antenna elements and shaping the ground plane. Both the computed and experimental results confirm that the antenna possesses a wide impedance bandwidth of 54.5% across 1.6-2.8 GHz, with a reflection coefficient and mutual coupling better than -10 and -14 dB, respectively. By further validating the simulated and the measured radiation and MIMO characteristics including far-field, gain, envelope correlation and channel capacity loss, the results show that the antenna can offer effective MIMO/diversity operation to alleviate multipath environments.

Yes / Empirical results of an electrically small printed monopole antenna is described with fractional bandwidth of 185% (115 MHz–2.90 GHz) for return-loss better than 10 dB, peak gain and radiation efficiency at 1.45 GHz of 2.35 dBi and 78.8%, respectively. The antenna geometry can be approximated to a back-to-back triangular shaped patch structure that is excited through a common feed-line with a meander-line T-shape divider. The truncated ground-plane includes a central stub located underneath the feed-line. The impedance bandwidth of the antenna is enhanced with the inclusion of meander-line slots in the patch and four double split-ring resonators on the underside of the radiating patches. The antenna radiates approximately omnidirectionally to provide coverage over a large part of VHF, whole of UHF, entire of L-band and some parts of S-band. The antenna has dimensions of 48.32×43.72×0.8 mm3, which is corresponding with the electrical size of 0.235λ_0×0.211λ_0×0.003λ_0, where λ_0 is free-space wavelength at 1.45 GHz. The proposed low-profile low-cost antenna is suitable for application in wideband wireless communications systems. / H2020-MSCA-ITN-2016 SECRET-722424 and UK Engineering and Physical Sciences Research Council (EPSRC) under grant EP/E022936/1

Au cours de ces dernières années, les communications sans fil connaissent une croissance vertigineuse, avec le développement de standards de communication de plus en plus nombreux, qui ouvrent la voie à de multiples applications telles que : la téléphonie mobile, le biomédical, le maritime, le civil et le militaire. De nos jours, les communications sans fil se sont diversifiées et multipliées. Cela entraîne la conception d’antennes toujours plus innovantes, performantes et de taille de plus en plus réduite (miniaturisation). Le projet FLEXBEA (FLEXible BEAcon) a pour but le développement d’un nouveau concept de balises de détresse miniatures (AIS et COSPAS-SARSAT), faible coût, intégrées dans des équipements de sécurité maritime tels qu’un radeau de survie et un gilet de sauvetage. Ces équipements sont destinés aux professionnels de la mer et aux plaisanciers. L’atout majeur de ce nouveau concept est l’intégration dans des équipements de sécurité maritime d’une fonction de détresse en cas de problème majeur : homme à la mer (MOB, Man OverBoard) par exemple lors d’un naufrage. Différentes antennes ont été étudiées. Nous présentons des antennes planaires (de type dipôle ou monopôle imprimé) développées dans la bande UHF : une solution de dipôle avec brins repliés est proposée afin de réduire l'encombrement, et deux modes d'alimentation (symétrique / dissymétrique) sont comparés. Des exemples d'antenne monopôle sont ensuite présentés avec une modification de leur géométrie (structures de type Bow-tie ou méandre) pour assurer une miniaturisation optimale. Puis les antennes filaires retenues pour le projet, avec une modélisation de ces antennes par un circuit équivalent (RLC). Des formules analytiques sont proposées afin de déterminer les valeurs de composants RLC qui interviennent dans le modèle circuit. Ensuite, nous sommes passés à la conception de l’antenne de la balise. Deux antennes ont été conçues et mesurées. Un monopôle ruban avec introduction de composants localisés pour la balise AIS et COSPAS-SARSAT, et une antenne hélice fonctionnant dans la bande AIS, intégrée dans la balise "SIMY". De nombreuses réalisations et mesures ont été effectuées pour caractériser ses antennes. / Over the last few years, wireless communications have grown dramatically, with the development of more and more communication standards, which open the way to multiple applications such as: mobile telephony, biomedical, maritime, the civilian and the military. Today, wireless communications have diversified and multiplied. This leads to the design of antennas that are always more innovative, more efficient and smaller in size (miniaturization). The FLEXBEA project (FLEXible BEAcon) aims to develop a new concept of low cost miniature distress beacons (AIS and COSPAS-SARSAT) integrated into marine safety equipment such as a life raft and a lifejacket safety. This equipment is intended for professionals of the sea and boaters. The main advantage of this new concept is the integration in maritime safety equipment of a distress function in case of major problem: man overboard (MOB, Man OverBoard) for example during a shipwreck. Different antennas have been studied. We present planar antennas (dipole type or printed monopoly) developed in the UHF band: a dipole solution with folded strands is proposed to reduce the bulk, and two modes of supply (symmetrical / asymmetrical) are compared. Examples of monopole antennas are then presented with a modification of their geometry (Bow-tie or meander type structures) to ensure optimal miniaturization. Then the wired antennas selected for the project, with a modeling of these antennas by an equivalent circuit (RLC). Analytical formulas are proposed to determine the RLC component values ​​involved in the circuit model. Then we went to the design of the beacon antenna. Two antennas were designed and measured. A ribbon monopoly with introduction of localized components for the AIS and COSPAS-SARSAT beacon, and a helix antenna operating in the AIS band, integrated into the "SIMY" beacon. Many achievements and measurements have been made to characterize its antennas.

In this thesis, the study mainly focuses on the current trends in development of compact multi-media mobile phone and provides a wideband monopole antenna design suitable for application in wireless communicating system in the near future. By utilizing the planar monopole antenna structure, the proposed antenna design is easy to be embedded into the mobile phone. Further, by using a shielding metal cover, we create a zone with low surface current distribution. This effect will reduce the electromagnetic coupling between the antenna and the electronic elements and make it possible to integrate more related elements into the mobile phones. Finally, we use the simulation software to analyze the dielectric effect caused by the casing of mobile phone and human body on the proposed antenna.

Dielectric resonator antenna (DRA) technologies are applicable to a wide variety of mobile wireless communication systems. The principal energy loss mechanism for this type of antenna is the dielectric loss, and then using modern ceramic materials, this may be very low. These antennas are typically of small size, with a high radiation efficiency, often above 95%; they deliver wide bandwidths, and possess a high power handling capability. The principal objectives of this thesis are to investigate and design DRA for low profile personal and nomadic communications applications for a wide variety of spectrum requirements: including DCS, PCS, UMTS, WLAN, UWB applications. X-band and part of Ku band applications are also considered. General and specific techniques for bandwidth expansion, diversity performance and balanced operation have been investigated through detailed simulation models, and physical prototyping. The first major design to be realized is a new broadband DRA operating from 1.15GHz to 6GHz, which has the potential to cover most of the existing mobile service bands. This antenna design employs a printed crescent shaped monopole, and a defected cylindrical DRA. The broad impedance bandwidth of this antenna is achieved by loading the crescent shaped radiator of the monopole with a ceramic material with a permittivity of 81. The antenna volume is 57.0  37.5  5.8 mm3, which in conjunction with the general performance parameters makes this antenna a potential candidate for mobile handset applications. The next class of antenna to be discussed is a novel offset slot-fed broadband DRA assembly. The optimised structure consists of two asymmetrically located cylindrical DRA, with a rectangular slot feed mechanism. Initially, designed for the frequency range from 9GHz to 12GHz, it was found that further spectral improvements were possible, leading to coverage from 8.5GHz to 17GHz. Finally, a new low cost dual-segmented S-slot coupled dielectric resonator antenna design is proposed for wideband applications in the X-band region, covering 7.66GHz to 11.2GHz bandwidth. The effective antenna volume is 30.0 x 25.0 x 0.8 mm3. The DR segments may be located on the same side, or on opposite sides, of the substrate. The end of these configurations results in an improved diversity performance.