A transferência de oxigênio é um fator limitante para grande parte dos cultivos em biorreatores que operam com organismos estritamente aeróbios devido à baixa solubilidade do oxigênio em meios de cultivo. A introdução de meios não convencionais, como polidimetilsiloxanos (PDMS), em biorreatores pode ser vista como uma melhoria para o ajuste desses processos. Este trabalho propõe uma investigação do emprego de polidimetilsiloxano fluido e emulsificado, usados como carreadores de oxigênio, em meios de cultivo na produção de lipases de Staphylococcus warneri EX17, cepa capaz de utilizar glicerol residual como substrato, visando melhorar a disponibilidade de oxigênio e aperfeiçoar a produtividade. Inicialmente, foram realizados estudos para selecionar o uso de glicerol residual, oriundo da síntese química de biodiesel como fonte de carbono. A atividade lipolítica foi semelhante com glicerol comercial e residual. Após a seleção do glicerol foram realizados experimentos em incubadora rotatória horizontal nas condições previamente otimizadas em trabalhos anteriores do grupo, adicionando PDMS. Dois tipos de PDMS foram testados, fluido e emulsificado. A produção de lipase foi significativamente maior no meio contendo PDMS. Assim, ferramentas de planejamento experimental, delineamento composto central (DCC) foram utilizadas para verificar a influencia do PDMS no coeficiente de transferência de oxigênio kLa em meio de cultivo produtor de lipase livre de células. O kLa aumentou significativamente no meio de cultivo contendo PDMS. Dois novos planejamentos foram desenhados, para otimizar a produção de lipase em meio de cultivo com células. Um para PDMS fluido e outro para PDMS emulsificado. No meio contendo PDMS fluido, a atividade lipolítica foi cinco vezes maior, enquanto que no meio contendo silicone emulsificado a atividade lipolítica foi três vezes maior. Este estudo demonstrou que a lipase de S. warneri EX17 pode ser produzida utilizando glicerol residual como fonte de carbono, e polidimetilsiloxanos como carreadores de oxigênio aumentando a transferência de oxigênio no meio e elevando a produção da enzima, que apresenta diversas possibilidades de aplicação, principalmente na indústria de alimentos. / The oxygen transfer is a limiting factor in many bioreactors cultivations, in which strictly aerobic organisms are grown due to the low solubility of oxygen in culture media. The introduction of unconventional media, such as polydimethylsiloxanes (PDMS) in bioreactors can be seen as a potential improvement for these processes. This work proposes an investigation of the use of polydimethylsiloxane in its two forms, fluid and emulsified, used as carriers of oxygen in culture media for the lipase production of Staphylococcus warneri EX17, strain capable of using glycerol as substrate, to improve the oxygen availability and improve enzyme productivity. Initially, studies were performed to select the use of residual glycerol, derived from the chemical synthesis of biodiesel as a source of carbon. The lipase activity was similar in both commercial and residual glycerol. Experiments were performed on orbital shaker, using conditions previously optimized in another work of the group, but with the addition of PDMS. Two types of PDMS were tested, the fluid and the emulsified. The lipase production was significantly higher in medium containing PDMS. Experimental design and central composite design (CCD) were used to evaluate the influence of PDMS on the oxygen transfer coefficient kLa in culture medium free of lipase-producing cells. The kLa increased significantly in the medium containing PDMS. Two new experimental plannings were designed to optimize the production of lipase in culture medium with cells. In the medium containing the PDMS fluid lipase activity was five times higher than medium without the oxygen carrier, while in the medium containing the emulsified silicone lipase activity was three times higher. This study showed that the lipase from S. warneri EX17 can be produced using residual glycerol as carbon source and that polydimethylsiloxanes works as interesting carrier of oxygen by increasing oxygen transfer rates, improving enzyme production, which has several possible applications, especially in the food industry.

A transferência de oxigênio é um fator limitante para grande parte dos cultivos em biorreatores que operam com organismos estritamente aeróbios devido à baixa solubilidade do oxigênio em meios de cultivo. A introdução de meios não convencionais, como polidimetilsiloxanos (PDMS), em biorreatores pode ser vista como uma melhoria para o ajuste desses processos. Este trabalho propõe uma investigação do emprego de polidimetilsiloxano fluido e emulsificado, usados como carreadores de oxigênio, em meios de cultivo na produção de lipases de Staphylococcus warneri EX17, cepa capaz de utilizar glicerol residual como substrato, visando melhorar a disponibilidade de oxigênio e aperfeiçoar a produtividade. Inicialmente, foram realizados estudos para selecionar o uso de glicerol residual, oriundo da síntese química de biodiesel como fonte de carbono. A atividade lipolítica foi semelhante com glicerol comercial e residual. Após a seleção do glicerol foram realizados experimentos em incubadora rotatória horizontal nas condições previamente otimizadas em trabalhos anteriores do grupo, adicionando PDMS. Dois tipos de PDMS foram testados, fluido e emulsificado. A produção de lipase foi significativamente maior no meio contendo PDMS. Assim, ferramentas de planejamento experimental, delineamento composto central (DCC) foram utilizadas para verificar a influencia do PDMS no coeficiente de transferência de oxigênio kLa em meio de cultivo produtor de lipase livre de células. O kLa aumentou significativamente no meio de cultivo contendo PDMS. Dois novos planejamentos foram desenhados, para otimizar a produção de lipase em meio de cultivo com células. Um para PDMS fluido e outro para PDMS emulsificado. No meio contendo PDMS fluido, a atividade lipolítica foi cinco vezes maior, enquanto que no meio contendo silicone emulsificado a atividade lipolítica foi três vezes maior. Este estudo demonstrou que a lipase de S. warneri EX17 pode ser produzida utilizando glicerol residual como fonte de carbono, e polidimetilsiloxanos como carreadores de oxigênio aumentando a transferência de oxigênio no meio e elevando a produção da enzima, que apresenta diversas possibilidades de aplicação, principalmente na indústria de alimentos. / The oxygen transfer is a limiting factor in many bioreactors cultivations, in which strictly aerobic organisms are grown due to the low solubility of oxygen in culture media. The introduction of unconventional media, such as polydimethylsiloxanes (PDMS) in bioreactors can be seen as a potential improvement for these processes. This work proposes an investigation of the use of polydimethylsiloxane in its two forms, fluid and emulsified, used as carriers of oxygen in culture media for the lipase production of Staphylococcus warneri EX17, strain capable of using glycerol as substrate, to improve the oxygen availability and improve enzyme productivity. Initially, studies were performed to select the use of residual glycerol, derived from the chemical synthesis of biodiesel as a source of carbon. The lipase activity was similar in both commercial and residual glycerol. Experiments were performed on orbital shaker, using conditions previously optimized in another work of the group, but with the addition of PDMS. Two types of PDMS were tested, the fluid and the emulsified. The lipase production was significantly higher in medium containing PDMS. Experimental design and central composite design (CCD) were used to evaluate the influence of PDMS on the oxygen transfer coefficient kLa in culture medium free of lipase-producing cells. The kLa increased significantly in the medium containing PDMS. Two new experimental plannings were designed to optimize the production of lipase in culture medium with cells. In the medium containing the PDMS fluid lipase activity was five times higher than medium without the oxygen carrier, while in the medium containing the emulsified silicone lipase activity was three times higher. This study showed that the lipase from S. warneri EX17 can be produced using residual glycerol as carbon source and that polydimethylsiloxanes works as interesting carrier of oxygen by increasing oxygen transfer rates, improving enzyme production, which has several possible applications, especially in the food industry.

Orientadores: Teresa Massako Kakuta Ravagnani, João Alexandre Ferreira da Rocha Pereira / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Quimica / Made available in DSpace on 2018-08-05T04:47:12Z (GMT). No. of bitstreams: 1 Lang_JeanPierre_M.pdf: 1967050 bytes, checksum: 0383f4c0388e6e7aa19f19c4c4688052 (MD5) Previous issue date: 2005 / Resumo: As colunas de recheio são equipamentos intensamente aplicados em operações de separação tais como destilação, absorção de dessorção. No entanto, a sua capacidade à transferência de massa em contracorrente é limitada devido à sua inundação. Uma nova tecnologia HIGEE ('high g¿ ¿ alta gravidade é proposta para superar esta limitação. Uma cluna HIGEE utiliza um recheio rotativo que induz acelerações centrífugas acima de 1000 vezes a aceleração da gravidade terrestre. O aumento da força motriz permite o aumento da capacidade e da eficiência da coluna. De acordo com vários autores, o tamanho do equipamento fica consideravelmente reduzido, apresentando vantagens econômicas e operacionais. A principal proposta deste trabalho é avaliar a forma como a coluna com recheio rotatico se comporta quando o raio externo do rotos é aumentado de 8 (Nascimento, 1999 e 2003) para 13cm.Os experimentos foram conduzidos em condições de refluxo total, sendo utilizando dois sistemas destilantes: n-hexano/n-heptano e etanol/água. A velocidade do rotor foi variada de 500 a 2300 rpm, criando acelerações contrifugas de 26 a256 vezes a aceleração da gravidade. O efeito da vazão de vapor, velocidade de rotação e do sistema destilante sobre o coeficiente de transferência de massa, 'K IND. y¿¿a IND. e¿ depende do fluxo de vapor, mas fracamente da velocidade do rotor...Observação: O resumo, na íntegra, poderá ser visualizado no texto completo da tese digital / Abstract: Packed colummns are equipment intensively applied in separations such as distillation, absorption and stripping , absorption and strippig. However, its for counter-current mass transfer is limited due to its flooding. A new HIGEE (high g ¿ high gravity) technology is proposal to overlap this limitation. A HIGEE column uses a rotating machine that promotes centrifugal accelerations above 1000 times the terrestrial gravity acceleration. The increase of the driving force allows the increase of column¿s capacity and efficiency. In accordance with some authors, the equipment size considerably reduced presenting economic and operational advantages. The main proposal of this work is to evaluate how the mass transfer behavior of the HIGEE column changes when the external rotor radius is increased from 8 (Nascimento 1999 and 2003) to 13 cm. The experiments had been conduced in total reflux conditions using two distilling system n-hexane/n-heptane and ethanol/ water. The rotor's speed was vaied from 500 to 2300 rpm , provided centrifugal accelerations from 26 to 556 times higher than terrestrial gravity acceleration. The effect of the vapor outflow, rotation speed and distilling system on mass transfer coefficient 'K IND. y¿¿a IND. e¿ and transfer unit area, 'AUT IND. G¿had been analyzed for each rotor size...Note: The complete abstract is available with the full electronic digital thesis or dissertations / Mestrado / Sistemas de Processos Quimicos e Informatica / Mestre em Engenharia Química

Hydrodynamic multiplicity in the trickle flow, or low interaction, regime is a well documented phenomenon. Multiple hydrodynamic states are often presented in the form of hysteresis loops where the hydrodynamic parameter studied are shown as a function of the operating history of the bed, i.e. liquid and gas flow rates. In extreme cases the lower leg, representing an increase in liquid flow rate on a pre-wetted and drained bed, is commonly referred to as the Levec mode. The upper extreme, referred to as the Kan-liquid mode, represents a decrease in liquid flow rate after operation in the high interaction regime. The many reported studies investigating liquid-solid mass transfer in trickle beds have generally used either the dissolution or electrochemical techniques. Numerous researchers have used their data to develop correlations predicting solid-liquid mass transfer coefficients. Most of these studies do not specify the multiplicity mode of operation. Only two studies (Sims et al. (1993) and Van der Merwe, Nicol&Al-Dahhan (2008)) use both the Levec and Kan-liquid operating modes. Both of these studies suggest that solid-liquid mass transfer also exhibit multiplicity behaviour although the trends suggested or speculated differ from each other. Sims et al. (1993) found that a Kan-liquid operated bed will outperform a Levec operated bed; however in contrast to this Van der Merwe et al. (2008) speculated that a Levec operated bed is better suited for liquid limited reactions due to enhanced liquid-solid mass transfer in the Levec mode as a result of faster interstitial velocity. This study showed that solid-liquid mass transfer coefficients, measured with both the dissolution and electrochemical technique, show multiplicity behaviour. Two distinct operating regions were found, which corresponds to the Levec and Kan-liquid modes. Measurements taken using the electrochemical technique yielded solid-liquid mass transfer coefficients larger than those measured using the dissolution method. The experimental results agree with the trend found by Sims et al. (1993) but the mass transfer coefficients in this study were significantly lower. Additionally it was shown that the difference in mass transfer coefficients, in the two modes, cannot be explained by merely compensating for the differences in wetting efficiency and interstitial velocity, suggesting that the Levec mode has a larger percentage of stagnant or poorly irrigated zones. It was also shown that mass transfer coefficients measured at the top of the column is higher than those measured at the bottom, suggesting that the flow structure is changing as a function of axial length. Lastly, with regards to electrochemical measurements of liquid-solid mass transfer, it was shown that measurements using a single particle electrode compared well to that of a multiple packing electrode. / Dissertation (MEng)--University of Pretoria, 2009. / Chemical Engineering / unrestricted

There exist several different numerical models for predicting bubble coalescence and breakup using computational fluid dynamics (CFD). Various combinations of these models will be employed to model a bioreactor process in a stirred reactor tank. A mass transfer coefficient, Kla, has been calculated and compared to those found experimentally by Thermo-Fisher Scientific, to validate the accuracy of currently available mathematical models for population balance equations. These include various combinations of bubble breakup and coalescence models coupled with the calculation of mass transfer coefficients.

Os óleos essenciais cítricos possuem uma ampla variedade de aplicações em diversos ramos das indústrias químicas, farmacêuticas, de alimentos, entre outras. Na indústria de cosméticos, mais precisamente no ramo de perfumaria, os ativos naturais cítricos (provenientes dos óleos de bergamota, limão, lima, mandarina, laranja, etc) são empregados nas formulações de colônias, cremes hidratantes e loções. Além disso, estes compostos são largamente utilizados como agentes aromatizantes nas indústrias alimentícias e farmacêuticas e empregados como matéria-prima para as indústrias de aromas. Com o objetivo de melhorar a qualidade dos óleos essenciais e sua capacidade aromatizante, alguns processos têm sido desenvolvidos para enriquecer a mistura com compostos oxigenados, os quais são reportados como os principais responsáveis pelo aroma característico da fruta. Tal processo é comumente conhecido como desterpenação e consiste na concentração destes compostos pela retirada de hidrocarbonetos terpênicos do óleo e pode ser realizado por meio da extração líquida ou extração por solvente. Neste contexto, esta dissertação de mestrado teve como finalidade estudar da viabilidade técnica do processo de desterpenação de óleo essencial cítrico modelo composto por limoneno e linalol. Os experimentos foram conduzidos em coluna de discos rotativos perfurados (PRDC) sob condição de temperatura controlada e pressão ambiente local. O equipamento operou de modo contínuo e contracorrente, utilizado como solventes soluções de etanol com teores de água de 30 e 40% (em massa), velocidade de rotação dos discos de 150, 200 e 250 rpm e razão entre a vazão mássica de solvente e alimentação de 0,5; 1,25; 2,5 e 3,0. Avaliou-se, também, o comportamento da densidade e viscosidade das fases extrato e rafinado oriundas da coluna de extração. Através deste estudo foi possível verificar que a tecnologia de desterpenação de óleos essenciais por meio da extração líquido-líquido é viável podendo ser aplicada à processos contínuos utilizando equipamento PRDC, por exemplo, sendo possível a obtenção de frações enriquecidas do composto oxigenado (linalol). / Citrus essential oils are used in a wide variety of applications in various branches of the chemical, pharmaceutical, food and other industries. In the cosmetics industry, specifically in the field of perfumery, natural citrus assets (from the essential oils of bergamot, lemon, lime, mandarin, orange, etc.) are used in the formulations of colonies, moisturizing creams and lotions. Furthermore, these compounds are widely used as flavoring agents in food and pharmaceutical industries and as raw material for the flavor industry. With the aim to improve the quality of essential oils and its flavoring ability, some processes have been developed to enrich the mixture with oxygenated compounds, which are reported as the main responsible for the characteristic aroma of the fruit. Such process is commonly known as deterpenation, and consists in concentration of these compounds by the removal of terpene compounds from the essencial oil and can be performed by liquid or solvent extraction. In this context, the purpose of this dissertation of master\'s degree was to carry out a study of the technical feasibility of deterpenation process of a citrus essential oil model composed by a mixture of limonene and linalool. The experiments of deterpenation were conducted in a perforated rotating discs contactor (PRDC) under controlled conditions of temperature and local environment al pressure. The equipment was operated in continuously and countercurrently mode, using as solvents ethanol solutions with 30 and 40% of water contents (by mass), rotation of discs speed of 150, 200 and 250 rpm and the mass flow rate of the solvent and feed ratio of 0.5, 1.25, 2.5 and 3.0. The behavior of the density and viscosity of the extract and raffinate phases from the extraction column was also evaluated. It was found that the deterpenation of essential oils by liquid-liquid extraction technology is feasible and can be applied to continuous processes using PRDC column extraction type, for instance, being possible to obtain enriched fractions of oxygenated compounds (linalool).

Recombinant Pichia pastoris is one of the important methylotropic yeast due to its robustness and ability to produce hormones like human chorionic gonadotropin (hCG), luteinizing hormone (LH) extracellularly. High growth on glycerol and strong protein expression on methanol by insertion of alcohol oxidase (AOX) promoter demand the fermentation to be a multistage operation. Methylotropic pathway demands more oxygen as methanol has to be converted to formaldehyde with half mole of oxygen. Moreover as fermentation progresses cell density in the reactor also increases. In case of Pichia pastoris fermentation cell density usually reaches very high (above 100 gm/lit) at the end of fermentation. Both these contribute in the increased oxygen demand in the fermentation and oxygen transfer turns out to be a limiting step. The present study focuses on the oxygen transfer process and its improvement in the fermentation. Oxygen transfer in bioreactor is a multistep process and involves different kinetic as well as mass transfer steps. In case of fermentation especially at high cell densities, oxygen transfer from bubbles to the broth becomes limiting step. The interface transport is governed by many physical as well as kinetic parameters. It is essential to screen these parameters from the whole set to identify the key parameters. Sensitivity analysis is carried out by using Metabolic Control Analysis (MCA) to quantify the effects of different parameters. It is found that bubble size and oxygen partial pressure are two such key parameters which can be manipulated. Use of pure oxygen to increase partial pressure and thereby solubility of oxygen in broth is a common approach. This work focuses on bubble size manipulation to increase the oxygen transfer rates.The idea behind this work is on to generate micron sized bubbles and utilize them effectively in the fermentation. There are many techniques reported to generate microbubble dispersions. In this work ’Spinning Disc microbubble Generator’ is fabricated to generate microbubbles. A flat disc surrounded by baffles with 5 mm gap in between, when subjected to 5000 rpm generates microbubbles. Some modifications are done to the set up to achieve desired properties of the bubbles. The bubbles generated fall in the range of 30-300 micron with mean size of about 60 micron. Use of Tween-20 surfactant stabilize the bubbles and hence offer a good resistance to coalescence and breakage. The liquid fraction in the bubbles can be as high as 40%. Contineous addition of this dispersion unnecessarily can dilute the fermentation broth. To overcome this volume constrain, a recirculation system is designed. Microbubble dispersion is added contineously to the reactor and equivalent fermentation broth is pumped back to the microbubble generator to achieve steady state to the liquid volume in both the vessels. Mass transfer studies with microbubbles show the potential of microbubble dispersion (MBD) to enhance mass transfer significantly. Decrease in volumetric mass transfer coefficient (KLa) due to surfactant is overcompensated by the increase in the interfacial area and net effect is, potential enhancement in KLa. The enhance- ment factor, that is, ratio of mass transfer coefficient with MBD to mass transfer coefficient with conventional sparging, is obtained to be about 4 to 5. Prior to utilization of bubbles in the recirculation system, cells are checked for the shear sensitiveness. Negligible lysis losses and almost no effect on growth patterns in shake flask culture confirm that the cells used are mechanically stable at operating conditions. Better growth patterns in shake flask are observed when microbubbles are pumped for predetermined duration in the broth. It shows possible use of MBD as oxygen carriers. Glycerol batch phase with MBD and conventional sparging is studied at different initial cell densities. Conventional sparging fails to grow the cells and Dissolved Oxygen (DO) levels close to zero suggest high oxygen demands which can not be sustained by conventional sparging. The same batch is run using MBD. Reasonably good growth patterns are observed. DO levels are well above 70% for most of the time during operation. High oxygen demand which can not be sustained by conventional sparging alone can be sustained by MBD. In this way in high den- sity cultures utilization of MBD can be a good alternative to fulfill required oxygen demand in fermentation.

No description available.

Este trabalho trata de um estudo experimental da transferência de calor e de massa de um condensador evaporativo, bem como, da relação existente entre as grandezas envolvidas durante a sua operação. Para o desenvolvimento da pesquisa foi construído um condensador evaporativo de pequeno porte com dimensões proporcionais a condensadores comercialmente fabricados no Brasil para operar com R-22 como fluido refrigerante. Este condensador tem 35 colunas e 12 fileiras de tubos de cobre de 6,35 mm de externo e opera junto a uma instalação que proporciona o escoamento de R-22 por termossifao. O distribuidor de água também foi construído em cobre e o eliminador de gotas em alumínio, assim como a estrutura do condensador. As laterais e a bandeja de recolhimento de água foram construídas em vidro para permitir a visualização do escoamento da água que e aspergida sobre os tubos. A fim de variar as condições operacionais, este condensador foi acoplado a um ventilador centrifugo acionado por um conversor de freqüência e a um circuito que permitiu a variação da vazão de água aspergida sobre os tubos. Dos ensaios resultaram 79 amostras de medição, que serviram para verificar a relação existente entre grandezas, bem como avaliar os coeficientes de transferência de calor e massa. Foram determinados os coeficientes de transferência de calor médio e local para o R-22. Alem disso, foram verificadas as regiões onde ocorrem o dessuperaquecimento, a mudança de fase e o subresfriamento do fluido refrigerante, e foram confrontados os coeficientes globais de transferência de calor obtidos a partir dos dados experimentais com aqueles obtidos por correlações para as regiões de condensação e subresfriamento. Destas investigações, resultou uma correlação para o coeficiente global de transferência de calor que visa determinar esta grandeza através das condições operacionais e das características geométricas do condensador. O Maximo desvio encontrado entre os valores provenientes dos dados experimentais e aqueles calculados pela correlação foi inferior a 10%. / This work presents an experimental heat and mass transfer study of an evaporative condenser, as well as, the relationship between measured quantities obtained during its operation. A small scale evaporative condenser was built in agreement to the real size equipment geometric similarity. The small scale condenser has a bundle of 210 copper tubes, with the outer diameter equal to ¼ inch, which were arranged in 35 columns and 6 rows and operating connected to the thermosifon facility that promote R-22 flow. The spray water distributor is also built on copper and the drift eliminator on aluminum, as well as the evaporative condenser structure. This condenser bounds were constructed as a glass enclosure to allow for the spray water flow visualization. To evaluate the operational conditions, the equipment was attached to a centrifugal fan controlled by a frequency inverter and a spray water circuit which allows for water quantity changing. From the carried out tests, 79 measuring samples were obtained and used to verify the quantities relationship, as well as, to evaluate the heat and mass transfer coefficients For the R-22 were determined the local and average heat transfer coefficients. Furthermore, the dessuperheating, condensation and subcooling regions were verified and compared both, the experimental overall heat transfer coefficient and those calculated by correlations at condensation and subcooling zones. From these investigations a correlation for the overall heat transfer coefficient is proposed. Its application allows determining the coefficient using the operational conditions and the geometric condenser features. The higher deviation found between the experimental data and the presented correlation is lower to 10%.

Este trabalho trata de um estudo experimental da transferência de calor e de massa de um condensador evaporativo, bem como, da relação existente entre as grandezas envolvidas durante a sua operação. Para o desenvolvimento da pesquisa foi construído um condensador evaporativo de pequeno porte com dimensões proporcionais a condensadores comercialmente fabricados no Brasil para operar com R-22 como fluido refrigerante. Este condensador tem 35 colunas e 12 fileiras de tubos de cobre de 6,35 mm de externo e opera junto a uma instalação que proporciona o escoamento de R-22 por termossifao. O distribuidor de água também foi construído em cobre e o eliminador de gotas em alumínio, assim como a estrutura do condensador. As laterais e a bandeja de recolhimento de água foram construídas em vidro para permitir a visualização do escoamento da água que e aspergida sobre os tubos. A fim de variar as condições operacionais, este condensador foi acoplado a um ventilador centrifugo acionado por um conversor de freqüência e a um circuito que permitiu a variação da vazão de água aspergida sobre os tubos. Dos ensaios resultaram 79 amostras de medição, que serviram para verificar a relação existente entre grandezas, bem como avaliar os coeficientes de transferência de calor e massa. Foram determinados os coeficientes de transferência de calor médio e local para o R-22. Alem disso, foram verificadas as regiões onde ocorrem o dessuperaquecimento, a mudança de fase e o subresfriamento do fluido refrigerante, e foram confrontados os coeficientes globais de transferência de calor obtidos a partir dos dados experimentais com aqueles obtidos por correlações para as regiões de condensação e subresfriamento. Destas investigações, resultou uma correlação para o coeficiente global de transferência de calor que visa determinar esta grandeza através das condições operacionais e das características geométricas do condensador. O Maximo desvio encontrado entre os valores provenientes dos dados experimentais e aqueles calculados pela correlação foi inferior a 10%. / This work presents an experimental heat and mass transfer study of an evaporative condenser, as well as, the relationship between measured quantities obtained during its operation. A small scale evaporative condenser was built in agreement to the real size equipment geometric similarity. The small scale condenser has a bundle of 210 copper tubes, with the outer diameter equal to ¼ inch, which were arranged in 35 columns and 6 rows and operating connected to the thermosifon facility that promote R-22 flow. The spray water distributor is also built on copper and the drift eliminator on aluminum, as well as the evaporative condenser structure. This condenser bounds were constructed as a glass enclosure to allow for the spray water flow visualization. To evaluate the operational conditions, the equipment was attached to a centrifugal fan controlled by a frequency inverter and a spray water circuit which allows for water quantity changing. From the carried out tests, 79 measuring samples were obtained and used to verify the quantities relationship, as well as, to evaluate the heat and mass transfer coefficients For the R-22 were determined the local and average heat transfer coefficients. Furthermore, the dessuperheating, condensation and subcooling regions were verified and compared both, the experimental overall heat transfer coefficient and those calculated by correlations at condensation and subcooling zones. From these investigations a correlation for the overall heat transfer coefficient is proposed. Its application allows determining the coefficient using the operational conditions and the geometric condenser features. The higher deviation found between the experimental data and the presented correlation is lower to 10%.