One-dimensional (1D) nanostructures (NSs) of Zinc Oxide (ZnO) such as nanorods (NRs) have recently attracted considerable research attention due to their potential for the development of optoelectronic devices such as ultraviolet (UV) photodetectors and light-emitting diodes (LEDs). The potential of ZnO NRs in all these applications, however, would require synthesis of high crystal quality ZnO NRs with precise control over the optical and electronic properties. It is known that the optical and electronic properties of ZnO NRs are mostly influenced by the presence of native (intrinsic) and impurities (extrinsic) defects. Therefore, understanding the nature of these intrinsic and extrinsic defects and their spatial distribution is critical for optimizing the optical and electronic properties of ZnO NRs. However, identifying the origin of such defects is a complicated matter, especially for NSs, where the information on anisotropy is usually lost due to the lack of coherent orientation. Thus, the aim of this thesis is towards the optimization of the lowtemperature solution-based synthesis of ZnO NRs for device applications. In this connection, we first started with investigating the effect of the precursor solution stirring durations on the deep level defects concentration and their spatial distribution along the ZnO NRs. Then, by choosing the optimal stirring time, we studied the influence of ZnO seeding layer precursor’s types, and its molar ratios on the density of interface defects. The findings of these investigations were used to demonstrate ZnO NRs-based heterojunction LEDs. The ability to tune the point defects along the NRs enabled us further to incorporate cobalt (Co) ions into the ZnO NRs crystal lattice, where these ions could occupy the vacancies or interstitial defects through substitutional or interstitial doping. Following this, high crystal quality vertically welloriented ZnO NRs have been demonstrated by incorporating a small amount of Co into the ZnO crystal lattice. Finally, the influence of Co ions incorporation on the reduction of core-defects (CDs) in ZnO NRs was systematically examined using electron paramagnetic resonance (EPR).

Lithium-ion batteries are of great importance for today's society. The state-of-the-art batteries that are used today use a fluorinated electrolyte that contains the salt LiPF6 and acts as both a safety hazard and an environmental issue due to its ability to form the toxic gas hydrogen fluoride (HF). This project aims to find a fluorine-free electrolyte that can be used in silicon-based lithium-ion batteries to make them more environmentally friendly without detriment to the electrochemical performance. To do so, an additive that may form a solid electrolyte interphase (SEI) stable enough to allow a fluorine-free electrolyte to replace the ones used today is sought for. The salt of interest is lithium  bis(oxalato)borate (LiBOB). Based on previous research electrolytes using LiBOB in either the solvent γ-Butyrolactone (GBL) or a mixture of ethylene carbonate (EC) and ethyl methyl carbonate (EMC) are examined. The additives used are vinylene carbonate (VC) and 1,3,2-dioxathiolane 2,2-dioxide (DTD). Techniques used are cyclic voltammetry, linear sweep voltammetry, galvanostatic charge and discharge, X-ray photoelectron spectroscopy and scanning electron microscopy.  The cells using GBL as solvent have cycled very poorly during this project while LiBOB in EC:EMC + VC shows the most promising results, with highest capacity retention and less amount of degraded LiBOB during the first charge. It is also to be noted that both EC:EMC based electrolytes provide the formation of a passivating solid electrolyte interface (SEI) and are of interest for further investigation based on the results obtained during this project.

There are many interesting applications of proton conducting oxides, such as electrolytes in fuel cells, hydrogen sensors and catalytic membranes for hydrogenation or dehydrogenation of organic compounds. Previous work explored doping BaTiO3 with the Rare Earth Element (REE) Sc to introduce oxygen vacancies in the structure, making it a Proton Conductor (PC). PC oxides are often perovskite materials, ABX3, wherethe A- or B-site are doped in such a way that less oxygen can be contained, creating oxygen vacancies. When these materials are then hydrated so that water molecules occupy the vacancies, hydrogen is essentially added to the system in the form of protons. This study expanded on those results, exploring possible dopants that are non-REEs, theoretically improving availability and cost. Fe and Al were chosen as B-site dopants and Sr was included as an alternative to Ba as the A-site cation, compensating for the smaller size of the Fe- and Al atoms compared to Ti. Solid state synthesis was used to manufacture the different compounds and then X-Ray Diffraction (XRD), ThermoGravimetric Analysis (TGA) and Differential Thermal Analysis (DTA) were used inorder to investigate their properties. The main focus was to explore ift he materials could be synthesised using this method, their structures and how they reacted to hydration. All Al doped samples could not be made phase pure with the synthesis parameters used. BaTi0.5Fe0.5Oy was stabilised by the inclusion of Ti, as it did not decompose during hydration, unlike pure BaFeOx. Significant hydration was achieved in a wet nitrogen atmosphere at 185°C, but its structure type was hexagonal, which is known to be unfavourable for proton conduction. SrTi0.5Fe0.5Oy had a cubic structure which is a beneficial structural trait for proton conduction, but negligible hydration was observed by TGA. A small increase in cell volume indicates that it might still have taken up some water, but the methods used for hydration were not optimal for this material. The oxygen content of the materials was not determined in this project and methods such as Mössbauer spectroscopy and iodometric titration should be included in any related future studies.

This thesis explores how to use the dry nanoporous structure of cellulosic fibres in new types of composite materials. A large effort was also given on how to correctly characterize the structure of fibres where the wet structure has been preserved also in the dry state. Delignified wood fibres have an open fibrillar structure in their water-swollen state. In the present work, this open fibrillar structure was preserved in the dry state by performing a liquid exchange procedure and the samples were thereafter carefully dried with Ar(g). The samples of never-dried TEMPO-oxidized dissolving pulp had a specific surface area of 130 m2/g in the dry state, as measured using the Brunauer, Emmet, and Teller (BET) Nitrogen gas adsorption method. This open structure was also revealed using field emission scanning electron microscopy (FE-SEM). The water-swollen and dry open structures were thoroughly characterized for various pulps. A new method for determining the pore size of water-swollen delignified cellulosic fibres is presented. By combining the results from solid state nuclear magnetic resonance NMR, measuring the specific surface area [m2/g] in the water-swollen state, with fibre saturation point (FSP), measuring the pore volume of fibres in water-swollen state [mass water/mass fibre], the average pore size can be determined without the need of assuming a certain pore geometry. The dry nanoporous structure was then used as a scaffold for in-situ polymerization, to demonstrate how the properties of the fibrils in the fibre wall can be exploited without the need to disintegrate the fibre wall. Both poly(methylmethacrylate) (PMMA) and poly(butylacrylate) (PBA) were successfully used as the polymeric matrix, and both nanocomposites (i.e., fibre/PMMA and fibre/PBA) had a fibre content of approximately 20 w%. The structure of the composites was characterized using SEM and Atomic Force Microscopy (AFM) operated in the phase imaging mode. The AFM results indicate that the cellulose aggregates and polymeric matrix were successfully mixed on a nanoscale, creating a nanocomposite of interpenetrating polymer molecules and cellulose fibrils, rather than a microcomposite, when using microscopic cellulose fibres. The water absorption capacity of the nanocomposites was reduced significantly, indicating that almost all nanopores in the fibre wall were successfully filled with matrix polymer. The mechanical properties were investigated, showing the importance of nanosized reinforcement compared to fibres of micrometer size. / <p>QC 20121011</p>

Fibers are classified into two groups; natural fibers and man-made fibers (MMF). There are three kinds of MMF: those made by transformation of natural polymers, those made from synthetic polymers and those made from inorganic material. Chitosan is classified as a biobased polymer and can be spun into man-made fibers. Due to its various functions, including anti-microbial, biocompatibility, biodegradability, metal-chelating, metal ions-coupling properties and general high molecular affinity, much attention has been paid recently to include chitosan into various concepts. The overall aim of this master thesis was to investigate the possibilities to make an antibacterial paper. Because chitosan contain primary amino groups that are cationic under mildly acidic conditions, it has antibacterial properties. Lab scale spinning of chitosan filaments was attempted in order to produce chitosan staple fibers that could be mixed with pulp fibers to make paper with antibacterial properties. Spinning methods used for a particular polymer is determined by the characteristics of the polymer. In the development of chitosan spinning at laboratory scale three different spinning methods were tested. A successful filament was produced by dry wet spinning. The filament was superior to the others in terms of dope composition and weight ratio of chitosan/acetic acid for protonation of the amino groups. Furthermore, the addition of glycerol improved the swelling of the chitosan hydrogel (or dope). Moreover, the condition of the coagulation step resulted in a good solidified filament with satisfactory elasticity and strength to be able to be taken up by a drawing cylinder. However, too small amounts of chitosan were produced in the development of chitosan spinning at lab scale and for production of antibacterial paper of chitosan. A second option was melt spinning of polylactide (PLA) filaments containing various amounts of chitosan. In this case PLA act as a carrier of chitosan into the paper sheet. Continuous filaments were spun in a sufficient amount. The antibacterial activity of PLA/chitosan fibers on E. coli bacteria was tested both on PLA/chitosan fibers as well as on suspensions. Under nutrient free conditions weak antibacterial effects was observed both for fibers and suspensions. However, in a more nutrient rich environment no effect was observed. This suggests that the produced fibers only had a weak antibacterial activity. To my knowledge the use of PLA in fiber form to carry chitosan into paper has not been attempted previously although different approaches to use chitosan as e.g. wound dressing is well described. In conclusion, there is a possibility to produce man made biodegradable fibers using chitosan and PLA that potentially could be added to paper. This paper might exert antibacterial properties that could have an interest to the market, e.g. for cleaning, in hospitals, and in the food industry.

Oxygen reduction reaction (ORR) has considerable potential for the pro-duction of electricity, issues with water splitting and many other applications in the energy sector. But in order to increase the efficiency of the reaction an electrocatalyst needs to be introduced. In today’s industrial devices precious and costly metals such as platinum (Pt) are used as catalysts. Other more abundant and cheaper alternatives, for example cobalt oxides, are therefore being investigated. In this thesis, pure cobalt (Co) thin films were synthesised to investigate if thin films can be used for the catalysis of ORR. This was successfully carried out by electrochemically modifying the thin films and grow catalytically ac-tive hexagonal cobalt oxide nanoparticles.   Multicomponent system CoCrFeNi is an emerging alloy system with high research interest for its high corrosion resistance suitable for harsh environments in which the applications for ORR are found. In this thesis, CoCrFexNi were synthesised as thin films. The corrosion resistance of the films was investigated in addition to their catalytic activity. The effect of Fe content on these properties was also studied. The presence of Fe was crucial for the electrochemical activation of films and catalytic activity towards ORR.  In summary, this thesis shows that cobalt based thin films can be used as catalysts combined with corrosion resistance for ORR applications.

Liquid based electrolytes are known to have safety issues and for their low volumetric energy densities to meet the future energy storage demand. Solid electrolytes based on ion conducting solid ceramic and solid polymer electrolytes are being studied and considered as an alternative to alleviate the issues with liquid electrolytes. Their mechanical property to better suppress dendrite formation gives them an edge to be considered in the realization of high - capacity lithium metal batteries. However, each have such issues associated with them as low ionic conductivity in the case of polymer electrolytes and bad interfacial contact with the lithium anode in the case of inorganic ionic conducting solid electrolytes. Polymer – ceramic composite electrolytes are regarded as a promising option to take advantage of the merits of both and obtain a solid electrolyte which can conduct lithium ions as high as in the mS/cm scale with good electrode – electrolyte interfacial contact, a high electrochemical stability window and high lithium dendrite suppression. This work has aimed to tune the surface of the garnet type ceramic electrolyte, Li7La3Zr2O7, referred to as LLZO, by acid treatment to bring about a better conductivity and lithium – ion transference number of the composite it is applied to. The acid, oxalic acid in this work, treatment has produced the required surface groups, hydroxide ion and oxalate ion, which are hypothesised to help improve the conductivity through the beneficial interactions they bring into the matrix. The conductivity and transference number measurements have revealed the treatment of the LLZO with the acid to have a positive impact on the conductivity and lithium – ion transference number of the composite compared to the untreated counterpart. Typical of the results obtained are the increment in conductivity and the lithium-ion transference number of composites containing 50 % ceramic (LLZO) mass loading. Across all the temperatures the conductivity is measured, an increment by a range of 2.5 times (at room temperature) to 7.8 times (at 60 0C) was obtained. Similarly, the lithium-ion transference number has increased from 0.121 in the composite containing 50 % untreated (pristine) LLZO to 0.159 in the composite containing the same mass loading of oxalic acid treated LLZO.

The field of organic solar cells is getting more and more attention as the need forrenewable energy sources rises. When developing new materials for organic solar cellssynthesizing the new materials, is a time consuming and costly process. Therefore acomputational model for predicting how effective a new material, is without the needfor synthesizing. In this thesis an attempt to create a model for predicting open circuitvoltage in organic solar cells. Descriptors was calculated using B3LYP/6-31G hybridfunctionals. By creating a data set of donor and acceptor molecules with known andunknown open circuit voltage, and empirically trying to find a correlation between thedata sets that can be extrapolated and modeled. The results of this thesis did notmeet the goal of creating a model for predicting the open circuit voltage. Where nosignificant correlation was found, due a to small sample size.

This project involves the fabrication and testing of microporous, polymer membranes designed to remove minute amounts of toxic air pollutants such as formaldehyde from air streams. The hypothesis to be tested is that active, the silver contained within the porous polymer membranes results in high formaldehyde retention. Monolayers consist of different sizes of sPS particles are assembled first on the silicon wafers by spin coating method and convective assembly method, respectively. Then each kind of monolayer with one dimension of sPS particles is deposited with a nanometer scaled silver thin film with a bench top metal evaporator. The porous membranes are produced by assembly of close-packed colloidal crystals of silver capped polystyrene template particles and subsequent infiltration with polyurethane prepolymer. The prepolymer is cured by UV exposure. The sPS particles are removed from the particle polymer membrane by treatment with organic solvents resulting in the formation of inverse opal structures. Silver does not dissolve in the organic solvents and cannot leave the pores due to the small size of connecting holes in an inverse opal. All the monolayers, cylindrical colloidal crystals and microcapillaries after infiltration of polyurethane had been characterized by optical microscope, and the porous membranes had been characterized by SEM. The application of porous membranes with silver caps is to absorb formaldehyde in the air, while in fact the silver caps are oxidized and become Ag2O, which will initiate a gas-phase/solid reaction with formaldehyde. In the future, TiO2 will be applied together with Ag2O, since TiO2 is another good absorbent for formaldehyde

This research thesis covers work done on building an atomic layer deposition (ALD) reactor followed by the development and optimization of an ALD process for indium oxide thin films on crystalline silicon substrates from new precursors using this new homebuilt cost-effective tool. This work describes the design, building and testing of the ALD system using an indium triazenide precursor and water in a novel precursor combination. The reactor was built to be capable of depositing films with comparable results to commercially built systems.Indium oxide thin films were deposited as the deposition temperature was varied from 154 to 517 0C to study the effects of deposition temperature on the obtained film thicknesses and ascertain the ALD temperature window between 269-384 0C. The presence of indium oxide films was confirmed with X-ray diffraction analysis, which was also used to study their crystallinity. The films were found to have a polycrystalline structure with a cubic phase. Measurement of film thickness was performed using X-ray reflectivity which determined a growth rate of approximately 1 Å/cycle. Elemental composition was determined by X-ray photoelectron spectroscopy which confirmed contamination-free indium rich films. Scanning electron microscope imaging was used to examine the surface morphology of the films as well as thick cross-sectional thicknesses.Since indium oxide films are potentially useful in various electronic, optical, and catalytic applications, emphasis is also placed on the accurate characterization of the chemical and physical properties of the obtained thin films. Optical and electrical properties of the produced transparent conducting oxide films were measured for transparency (and optical band gap) and electrical characterization by resistivity measurements, from UV-Vis spectrophotometry and 4-point probe data respectively. A high optical transmission &gt;70 %, a wide band gap 3.99-4.24 eV, and low resistivity values ∼0.2 mΩcm, showed that In2O3 films have interesting properties for various applications confirming indium oxide a key material in transparent electronics.