Research in future generation computing is focused on reducing energy dissipation while maintaining the switching speed in a binary operation to continue the current trend of increasing transistor-density according to Moore’s law. Unlike charge-based CMOS technology, spin-based nanomagnetic technology, based on switching bistable magnetization of single domain shape-anisotropic nanomagnets, has the potential to achieve ultralow energy dissipation due to the fact that no charge motion is directly involved in switching. However, switching of magnetization has not been any less dissipative than switching transistors because most magnet switching schemes involve generating a current to produce a magnetic field, or spin transfer torque or domain wall motion to switch magnetization. Current-induced switching invariably dissipates an exorbitant amount of energy in the switching circuit that nullifies any energy advantage that a magnet may have over a transistor. Magnetoelastic switching (switching the magnetization of a magnetostrictive magnet with voltage generated stress) is an unusual switching paradigm where the dissipation turns out to be merely few hundred kT per switching event – several orders of magnitude less than that encountered in current-based switching. A fundamental obstacle, though, is to deterministically switch the magnetization of a nanomagnet between two stable states that are mutually anti-parallel with stress alone. In this work, I have investigated ways to mitigate this problem. One popular approach to flip the magnetizations of a nanomagnet is to pass a spin polarized current through it that transfers spin angular moment from the current to the electrons in the magnet, thereby switching their spins and ultimately the magnet’s magnetization. This approach – known as spin transfer torque (STT) – is very dissipative because of the enormous current densities needed to switch magnets, We, therefore, devised a mixed mode technique to switch magnetization with a combination of STT and stress to gain both energy efficiency from stress and deterministic 180o switching from STT. This approach reduces the total energy dissipation by roughly one order of magnitude. We then extended this idea to find a way to deterministically flip magnetization with stress alone. Sequentially applying stresses along two skewed axes, a complete 180o switching can be achieved. These results have been verified with stochastic Landau-Lifshitz-Gilbert simulation in the presence of thermal noise. The 180o switching makes it possible to develop a genre of magneto-elastic memory where bits are written entirely with voltage generated stress with no current flow. They are extremely energy-efficient. In addition to memory devices, a universal NAND logic device has been proposed which satisfies all the essential characteristics of a Boolean logic gate. It is non-volatile unlike transistor based logic gates in the sense that that gate can process binary inputs and store the output (result) in the magnetization states of magnets, thereby doubling as both logic and memory. Such dual role elements can spawn non-traditional non-von-Neumann architectures without the processor and memory partition that reduces energy efficiency and introduces additional errors. A bit comparator is also designed, which happens to be all straintronic, yet reconfigurable. Moreover, a straintronic spin neuron is designed for neural computing architecture that dissipates orders of magnitude less energy than its CMOS based counterparts. Finally, an experiment has been performed to demonstrate a complete 180o switching of magnetization in a shape anisotropic magnetostrictive Co nanomagnet using voltage generated stress. The device is synthesized with nano-fabrication techniques namely electron beam lithography, electron beam evaporation, and lift off. The experimental results vindicate our proposal of applying sequential stress along two skewed axes to reverse magnetization with stress and therefore, provide a firm footing to magneto-elastic memory technology.

La dynamique des parois de domaine magnétiques (DW) soulève actuellement un très fort intérêt à la fois du point de vue fondamental mais aussi en lien avec ses applications dans des dispositifs logique et mémoire. Des dispositifs nouveaux basés sur les DW ont déjà été proposés, par exemple présentant des très fortes densités de stockage et des taux de transfert élevés pour un remplacement des disques durs. De plus dans les Mémoires Magnétiques à Accès Aléatoire (MRAM), identifiées comme l'une des solutions les plus prometteuses pour le remplacement des DRAM et SRAM, le retournement de l'aimantation implique une propagation des DW. Le contrôle de la dynamique des DW sous courant est longtemps resté un challenge, principalement à cause d'imperfections dans les matériaux utilisés. Des déplacements rapides et contrôlé des DW au moyen d'un courant ont été reportés il y a quelques années seulement dans des multicouches présentant une asymétrie d'inversion (SIA). Plus récemment un mécanisme a été proposé basé sur la présence de couple de spin orbite (SOT) et de l'interaction Dzyaloshinskii-Moriya (DMI), tout deux trouvant leur origine dans l'interaction spin-orbite et nécessitant une SIA.Mon objectif initial était de tester ce modèle dans deux systèmes présentant différents SIA. Dans des multicouches Pt/Co/Pt à faible SIA, j'ai étudié la propagation des DW sous courant et sous champ et j'ai mis en évidence l'existence d'un amortissement chiral. Ce phénomène nouveau, pendant de DMI pour les mécanismes dissipatifs, influence à la fois la dynamique sous courant et sous champ et doit être pris en compte pour avoir une description complète des mécanismes. Dans des multicouches Pt/Co/AlOx à fort SIA, j'ai étudié de nouvelles géométries pour lesquelles le mouvement de la paroi de domaine et la direction du courant ne sont pas colinéaires. J'ai mis en évidence un déplacement asymétrique des DW en fonction de cette non-colinéarité qui ne peut pas être expliquée avec un modèle simple DMI+SOT. En se basant sur ces résultats expérimentaux, j'ai introduit un nouveau concept de dispositifs, appelé « origami magnétique » : la forme du dispositif gouverne le mécanisme de retournement. Ce concept apporte une grande flexibilité dans la construction de mémoires magnétiques non volatiles, rapides et peu gourmandes en énergie : des fonctionnalités différentes peuvent être obtenues sur un même wafer simplement par la maîtrise de la forme des différents éléments. Je montre la preuve de concept de deux dispositifs. / Magnetic domain wall (DW) dynamics is currently attracting tremendous interest both from a fundamental point of view as well as in relation with emerging magnetic memory and logic devices. New DW-based devices were recently proposed, for example to replace hard drive disks with higher density and faster date transfer. Moreover, in Magnetic Random Access Memory (MRAM), identified as one of the most promising candidate for DRAM and SRAM replacement, switching occurs through DW propagation. Control of current induced DW dynamics has long been a challenge mainly due to material imperfections. Only some years ago, fast and controllable motions were reported in multilayers presenting structural inversion asymmetry (SIA). More recently, a mechanism was proposed based on the presence of spin orbit torques and Dzyaloshinskii-Moriya interaction (DMI), both phenomena originating from the spin orbit interaction and needing (SIA).My initial objective was to test this model in two systems presenting different SIA. In Pt/Co/Pt multilayers with weak SIA, I studied both current and field induced DW motion and evidenced a chiral damping. This new phenomena, counterpart of the DMI for the dissipative aspects, influences both current and field induced dynamics and has to be taken into account for a complete picture of the mechanism. In Pt/Co/AlOx multilayers with strong SIA, I studied new geometries where the DW motion the and current flow are not collinear. I evidenced asymmetric DW motion as a function of this non-collinearity that cannot be explained with a simple SOT+DMI model. Based on these experimental results I introduce a new device concept named “magnetic origami”: the shape of the device governs the switching mechanism. This concept provides large flexibility to construct fast, low power non-volatile magnetic memory: different functionalities can be achieved on a wafer by simply mastering the shape of the different elements. I show the proof of concept of two such devices.