This dissertation describes the study of excitonic optical nonlinearities in semiconductors and semiconductor microstructures. The main emphasis is placed on the evolution of optical nonlinearities as one goes from bulk to quantum-confined structures. Included are experimental studies of molecular-beam-epitaxially-grown bulk GaAs and ZnSe, GaAs/AlGaAs multiple-Quantum-Wells (MQW's), and finally, quantum-confined CdSe-doped glasses. The microscopic origins and magnitudes of the optical nonlinearities of bulk GaAs and ZnSe were investigated and the exciton recovery time in ZnSe was measured. A comparison with a plasma theory indicates that in GaAs, band filling and screening of the continuum-state Coulomb enhancement are the most efficient mechanisms, while in ZnSe, exciton screening and broadening are the dominating mechanism for the nonlinearity. The maximum nonlinear index per excited electron-hole pair of ZnSe at room temperature is comparable to that of bulk GaAs and the exciton recovery times are of the order of 100 ps or less. A systematic study of the dependence of the optical nonlinearities on quantum well thickness for GaAs/AlGaAs MQWs and the results of nonlinear optical switching and gain in a 58 A GaAs/AlGaAs MQW are reported and discussed. The maximum change in the refractive index is greatest for the MQWs with the smallest well size and decreases with increasing well size, reaching a minimum for bulk GaAs. The maximum index change per photoexcited carrier increases by a factor of 3 as the well size decreases from bulk to 76 A MQW. A differential energy gain of 0.2 and the contrast of 4 are measured for a 58 MQW using 3 ns laser pulses. The linear and nonlinear optical properties of CdSe semiconductor microcrystallites grown under different heat treatments in borosilicate glasses are investigated. Pump-probe spectroscopic techniques and interferometric techniques were employed to study size quantization effects in these microcrystallites (quantum dots). Nonlinear optical properties due to the transitions between quantum confined electron and hole states are reported for low temperature and room temperature. A relatively large homogeneous linewidth is observed. Single beam saturation experiments for quantum confined samples were performed to study the optical nonlinearities as a function of microcrystallite size. Results indicate that the saturation intensity is larger for smaller size quantum dots.

The aim of this work is to nondestructively characterize the industrial dual phase (ferritic-martensitic) steels (DPS) by the Magnetic Barkhausen Noise (MBN) method. By quenching of AISI 8620 steel specimens having two different starting microstructures, from various intercritical annealing temperatures (ICAT) in the ferrite-austenite region, the microstructures consisting of different volume fractions of martensite and morphology have been obtained. The microstructures, strength properties and hardness values were determined by conventional metallographic and mechanical tests. The measurements of the Magnetic Barkhausen Noise (MBN) were performed by using both Rollscan and &amp / #956 / SCAN sensor connectors. A good correlation between the martensite volume fraction, hardness and MBN signal amplitude has been obtained. MBN emission decreased as the ICAT, therefore the volume fraction of martensite increased. Moreover, MBN emission decreased as the martensite morphology become thinner. It has been concluded that MBN method can be used for nondestructive characterization of industrial dual phase steels.

In this thesis, Gallium Nitride (GaN) micro- and nanostructures were fabricated based on focused ion beam (FIB) milling. The starting wafer is an epitaxial structure containing InGaN/GaN multi-quantum wells. High crystal quality structures such as the nano-cone, nanopillar array and single pillar were fabricated based on the FIB method. During the fabrication process, various approaches were designed to minimize FIB damage caused by Gallium ion bombardment. The fabrication process for nano-cone is a combination of mask preparation by FIB with subsequent reactive ion etching (RIE). For fabricating nanopillar arrays, the nanopillars were patterned directly using FIB with an optimized beam current followed by wet etching process to remove the damage. On the other hand, the single pillar is achieved by gradually decreasing the ion beam current as the diameter of the pillar becomes smaller. The first order Raman spectra for the nanopillar array reveal a strong additional peak when the diameter of the nanopillars is less than 220 nm. This peak can also be observed in GaN pillars without MQW and is clearly assigned to the surface optical (SO) mode originated from the A1 phonon in wurtzite GaN. The frequency of this SO mode is found to be sensitive with the diameter and surface roughness of the nanopillars. Temperature-variable photoluminescence (PL) measurements show that a broadband emission in the as-grown sample split into the two well-resolved bands for nanopillars and the emission band at the higher energy side quickly thermally quenched. Room temperature PL measurements on the single pillars exhibit an increasing blue-shift of the peak emission with the decreasing of the pillar diameter. Additional simulation data and excitation power dependent PL studies confirm the observation of strain relaxation in the pillar’s MQW due to FIB fabrication. The temperature variable PL on the single pillar shows a monotonous blue shift as the temperature arises to 300 K. / published_or_final_version / Electrical and Electronic Engineering / Master / Master of Philosophy

In the TRISO (tristructural isotropic) coated fuel particle used in the High Temperature Reactor, the most important layer is a silicon carbide layer which acts as a pressure vessel. In this study, we have focused our study on the investigation of the Young’s modulus, hardness, residual stress, and fracture toughness of the SiC layer. Moreover, microstructures and impurities in silicon carbide were characterised and then related to both Young’s modulus and hardness of the SiC layer. Both nanoindentation and micro-indentation were used to determine Young’s modulus and hardness of the SiC. Raman spectroscopy, X-ray diffraction, and scanning electron microscopy techniques were used to examine impurities, phases and microstructure of silicon carbide layers, respectively. Young’s modulus was measured at different positions of a polished surface of the SiC with different CVD growth and crystal orientations. With help from the finite element modelling, it has been found that Young’s modulus of the SiC is dependent on the grain orientation of the SiC. Mechanical properties of silicon carbide are affected by the presence of excess silicon, excess carbon, stacking faults, texture, grain size, property of grain boundary. The effect of these factors on Young’s modulus and hardness, are investigated with the orthogonal analysis. The analysis concludes that the most important factor on Young’s modulus is texture while the most significant factor on hardness is grain boundary. Grain size is secondarily important factor to affect hardness. Stacking faults and impurities almost have no influence on Young’s modulus and hardness. The residual stress in the silicon carbide layer was measured based on the peak shift in Raman spectra of the SiC and is in a range of 150-300 MPa. Fracture resistance in the radial direction of the SiC layer is larger than those in the circumferential direction. The difference is controlled by the layer-like structure of the SiC coating.

Within the context of the imminent implementation of the Pb-free soldering in Europe in 2006, this thesis addresses the gap in understanding that has emerged in the fundamental materials issues between well-understood and mature lead-containing solders and a plethora of new, Pb-free solders for which there are neither long term reliability data nor understanding of the materials behaviour and how these might be influenced by manufacture and in-service conditions. In addition, this thesis also addresses the question as to whether the solder joint size and geometry could become a reliability issue and therefore affect the implementation of the Pb-free solders in ultrafine micro joints. Thermodynamic calculations using MTDATA (developed by the National Physical Laboratory, NPL, UK) together with a thermodynamic database for solders under either equilibrium or Scheil conditions, have shown their usefulness in Pb-free solder design and processing, generating a wealth of information in respect of the temperature dependence of phase formation and composition. The predictions from MTDATA on a number of selected systems is generally in good agreement with the results from experimental work, and has assisted in the understanding of the microstructure and mechanical properties of the Pb-free solders and the implications of their interactions with a tin-lead solder. However, further critical assessment and the addition of new elements into the solder database, such as Ni and P, are required to make MTDA TA a more effective computational tool to assist the optimization of processing parameters and cost-effective production in using Pb-free solders. Molten solder can interact with the under bump metallizations (UBM) and/or board level metallizations on either side of the solder bump to form intermetallic compounds (IMCs) during solder reflow. In the modelling of the kinetics of the dissolution process of UBM into the liquid solder, the commonly used NernstBrunner (N-B) equation is found to have poor validity for these calculations for micro joints at 100 μm in diameter or less. Three bumping techniques, i.e. solder dipping (SD), solder paste stencil printing followed by reflow (SPR) and electroplating of solders and subsequent reflow (EPR), are used to investigate the interfacial interactions of molten Sn/Sn-rich solders, i.e. pure Sn, Sn-3.5Ag, and Sn-3.8AgO.7Cu, on electroless nickel immersion gold (ENIG) and copper pads at 240°C. The resultant bulk and interfacial microstructures from a variety of pad sizes, ranging from 1 mm down to 25 μm, suggest that in general the small bumps contain smaller β-Sn dendrites and Ag₃Sn IMC particles, nevertheless the interfacial IMC is thicker in the smalI bumps than in the large bumps. In addition, one and two-dimensional combined thermodynamic and kinetic models have been developed to assist the understanding of the kinetics of interdiffusion and the formation of interfacial intermetallic compounds during reflow. Both the experimental results and theoretical predictions suggest that the solder bump size and geometry can influence the as-soldered microstructure, and therefore this factor should be taken into consideration for the design of future reliable ultrafine Ph-free solder joints.

No description available.

Multi-pass fusion welding by a filler wire (welding electrode) is normally carried out to join thick steel sections used in most engineering applications. Welded joints in an installation, is the area of critical importance, since they are likely to contain a higher density of defects than the parent metal and their physical properties can differ significantly from the parent metal. Fusion arc welding process relies on intense local heating at a joint where a certain amount of the parent metal is melted and fused with additional metal from the filler wire. The intense local heating causes severe transient thermal gradients in the welded component and the resulting uneven cooling that follows produces a variably distributed residual stress field. In multi-pass welds, multiple thermal cycles resulted in a variably distribution of residual stress field across the weld and through the thickness. These complex thermal stresses generated in welds are undesirable but inevitable during fusion welding. Presence of such tensile residual stresses can be detrimental to the service integrity of a welded structure. In addition to a complex distribution of residual stress state, multi-pass welds also forms dendritic grain structure, which are repeatedly heated, resulting in segregation of alloying elements. Dendritic grain structure is weaker and segregation of alloying elements would result in formation of corrosion microcells as well as reduction in overall corrosion prevention due to depletion of alloying elements.

ABSTRACT MICROWAVE SINTERING AND CHARACTERIZATION OF ALUMINA AND ALUMINA MATRIX CERAMIC NANOCOMPOSITES Kayiplar, Burcu M.S., Department of Metallurgical and Materials Engineering Supervisor: Assist. Prof. Dr. Arcan F. Dericioglu April 2010, 106 pages Efficiency of microwave heating on the sintering of ceramic materials has been investigated in comparison to conventional processing. Monolithic alumina with or without sintering additives such as MgO, CaO, Y2O3 were fabricated by both conventional and microwave sintering at temperatures ranging from 1000&deg / C to 1600&deg / C with a constant soaking time of 1 hour. Based on the densification results on monolithic alumina, nanometer-sized SiC or stabilized ZrO2 particle-dispersed alumina matrix ceramic nanocomposites were sintered by both methods at 1300&deg / C and 1500&deg / C for 1 hour. Sintered ceramic materials were characterized in terms of densification, microstructural evolution, chemical composition and mechanical properties such as hardness and indentation fracture toughness. Microwave sintering was determined to be a remarkably effective method in the production of Al2O3 ceramics at considerably low temperatures (&amp / #8804 / 1400&deg / C) compared to conventional sintering in achieving enhanced relative densities reaching to ~97% with improved microstructural characteristics and mechanical properties. Usage of sintering additives at temperatures higher than 1400&deg / C was determined to be effective in densifiying Al2O3 by both methods. Second phase particle incorporation yielded poor densification resulting in a decrease of hardness of the fabricated ceramic nanocomposites / however, their fracture toughness improved considerably caused by the crack deflection at the dispersed particles and grain boundaries reaching to ~4 MPa&middot / m1/2 in the case of SiC particledispersed nanocomposites. Compared to conventional sintering, microwave sintering is more effective in the processing of alumina and alumina matrix nanocomposites leading to similar densification values along with improved microstructural and mechanical characteristics at lower temperatures in shorter soaking periods.

High grade galvanized steel in large amounts is needed to match the increasing demand of automotive industry both in our country and in the world. Stainless steels, used in fabrication of zinc bath hardware of continuous galvanizing lines, lose their corrosion resistance due to various mechanisms in such mediums containing molten metals like zinc and aluminum. Consequently they corrode to the levels where they should be taken to maintenance or replaced. In this study, corrosion performance and the effect of typical galvanizing and age treating heat treatments to mechanical properties of 4 newly developed austenitic stainless steels and AISI 316L grade stainless steel were investigated and compared with each other. Experimental studies involved immersion corrosion tests for 168 and 504 hours followed by weight loss determinations and comparisons of corrosion performances of age treated and solution annealed stainless steels. Parallel with corrosion testing, delta ferrite content v determinations with 3 different methods, tensile tests and v-notch impact tests at 4 different heat exposure conditions were carried out and discussed. 2 new stainless steel compositions were selected to be used in fabrication of galvanizing hardware based on the comparisons of corrosion &amp / mechanical performances of candidate steels.

The behavior of cancer cells is strongly influenced by the properties of extracellular microenvironments, including topology, mechanics and composition. As topological and mechanical properties of the extracellular matrix are hard to access and control for in-depth studies of underlying mechanisms in vivo, defined biomimetic in vitro models are needed. Herein we show, how pore size and fibril diameter of collagen I networks distinctively regulate cancer cell morphology and invasion. Three-dimensional collagen I matrices with a tight control of pore size, fibril diameter and stiffness were reconstituted by adjustment of concentration and pH value during matrix reconstitution. At first, a detailed analysis of topology and mechanics of matrices using confocal laser scanning microscopy, image analysis tools and force spectroscopy indicate pore size and not fibril diameter as the major determinant of matrix elasticity. Secondly, by using two different breast cancer cell lines (MDA-MB-231 and MCF-7), we demonstrate collagen fibril diameter - and not pore size - to primarily regulate cell morphology, cluster formation and invasion. Invasiveness increased and clustering decreased with increasing fibril diameter for both, the highly invasive MDA-MB-231 cells with mesenchymal migratory phenotype and the MCF-7 cells with amoeboid migratory phenotype. As this behavior was independent of overall pore size, matrix elasticity is shown to be not the major determinant of the cell characteristics. Our work emphasizes the complex relationship between structural-mechanical properties of the extracellular matrix and invasive behavior of cancer cells. It suggests a correlation of migratory and invasive phenotype of cancer cells in dependence on topological and mechanical features of the length scale of single fibrils and not on coarse-grained network properties.