The aim of this dissertation was the design, implementation and performance evaluation of a Recursive Least Squares (RLS), lattice based, adaptive, multidimensional, decision feedback equaliser (DFE) for the spectrally efficient four-dimensional digital modulation technique, re¬ferred to as Quadrature-Quadrature Phase-Shift Keying, Q2pSK. Q2PSK constitutes a relatively new modulation technique, and the application of adaptive equalisation to this technique has not yet been considered in the open literature. This dissertation represents an in depth study into the Q2PSK modulation technique, as well as the optimal implementation, in simulation, of such a modem to aid the inclusion of the adap¬tive lattice DFE, for application to high speed mobile digital communication over the V /UHF channel in the presence of multi path propagation. Specific aspects of synchronization applicable to this modem platform are also addressed. An in depth study was also conducted into the realisation of a V /UHF channel simulation, capable of producing a Ricean and/or Rayleigh fad¬ing multipath propagation environment for the evaluation of the modem platform and adaptive equaliser structure. The theoretical analysis of the effect of multi path on a Q2PSK signal led to the correct design of the adaptive lattice structure, as well as the correct interfacing of the equaliser to the receiver platform. The performance of the proposed synchronisation strategies, in tandem with the equalisation technique were evaluated for several static, as well as fading multipath channels. The simulation results obtained show the equaliser operates correctly, and can give large performance gains over the static matched filter (matched to the transmitted waveform) implementation of the modem platform. Several simulations were specifically designed to highlight the performance limitations of the adaptive equalisation technique. / Dissertation (MEng (Digital Communication))--University of Pretoria, 2006. / Electrical, Electronic and Computer Engineering / unrestricted

The thesis deals with PLC technology and issues with Smart Metering. In the theoretical part, a principle of technology's functionality and its advantages and disadvantages were described. In the experimental part methodology of data concentrator and electric meters was designed. In addition, extensive testing set according to capturing of DLMS communication, link quality influencing, reading registers of meters were realized. In the second experimental part limits of communications between broadband BPL modems were detected by the power line communication hardware channel emulator. Measurement of throughput, latency, frame loss passed off according to RCF 2544, RFC 6349 recommendation and according to the methodology of TCP Throughput In the last part, two laboratory exercises were created, first one deals with Smart Metering system and communication between the data concentrator and electric meters and the second one deals with communication among broadband BPL modems not only for Smart Metering purposes.

Thesis (MScEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: In this thesis the design and testing of the baseband components of a modem intended for use as a telemetry and control link for a low earth orbit satellite is presented. This includes parts of the physical layer as well as a basic data-link layer. Binary phase-shift keying (BPSK) is used as the modulation scheme and is realised by making use of software defined radio on a standard x86 computer with digital to analogue and analogue to digital converters that use a universal serial bus (USB) connection. The data-link layer makes use of a basic framing scheme and provides bit synchronisation, an automatic repeat request (ARQ) system and Bose Chaudhuri Hocquenghem (BCH) forward error correction (FEC). The ARQ system ensures that data is delivered reliably and the FEC improves the system’s performance in noisy conditions. A prototype system was developed to test the performance of the individual layers as well as the system as a whole. For testing purposes the Linux Internet Protocol (IP) stack is used as higher network layers. Radio frequency hardware developed by Verschaeve [1] modulates the signal away from baseband, transmits it over the air and receives it. / AFRIKAANSE OPSOMMING: In hierdie tesis word die ontwerp en toetsing van die basisband komponente van ‘n modem, bedoel vir gebruik op ‘n satelliet in ‘n lae-aarde wentelbaan, bespreek. Die ontwerp sluit dele van die fisiese vlak sowel as ‘n verbindingsvlak in. Binêre faseskuifsleuteling word gebruik as die modulasieskema en word verwesenlik deur gebruik te maak van sagteware gedefinieerde radio. Dit voer uit op ’n standaard x86 rekenaar wat deur middel van USB gekoppel is aan ’n digitaal-na-analoog- en ’n analoog-na-digitaal-omsetter. Die verbindingsvlak het ‘n eenvoudige ramingskema. Dit voorsien bis sinkronisasie, die hersending van verlore rame en Bose Chaudhuri Hocquenghem (BCH) voorwaartse foutverbetering. Die hersending van verlore rame verseker dat data betroubaar oorgedra kan word en foutverbetering verbeter die stelsel se vermoëns in ruiserige toestande. ‘n Prototipe stelsel is ontwikkel om die vermoëns van die individuele vlakke, sowel as die stelsel as ’n geheel, te toets. Tydens toetsing is die Linux Internet Protokol stapel gebruik vir die hoër netwerk vlakke. Radio komponente wat deur Verschaeve [1] ontwikkel was is gebruik om die sein uit te saai en te ontvang.

The objective of this research is to present a low power modem technology for a high speed millimeter wave wireless system. The first part of the research focuses on a robust ASIC design methodology. There are several aspects of the ASIC flow that require special attention such as logical synthesis, timing driven physical placement, Clock Tree Synthesis, Static Timing Analysis, estimation and reduction of power consumption and LVS and DRC closure. The latter part is dedicated to high speed baseband circuits such as Coherent and Non coherent demodulator which are critical components of a multi-gigabit wireless communication system. The demodulator operates at input data rates of multiple gigabits per second, which presents the challenge of designing the building blocks to operate at speeds of multiple GHz. The high speed complex multiplier is a major component of the non coherent demodulator. As part of the coherent demodulator the complex multiplier derotates the input sequence by multiplying with cosine and sine functions, Costas error calculator computes the phase error in the derotated input signal. The NCO (Numerically controlled Oscillator) is a look up table based system used to generate the cosine and sine functions, used by the derotator.The CIC filter is used to decimate the costas error signal as the loop bandwidth is significantly smaller compared to the sampling frequency. All these modules put together form the coherent demodulator which is an integral part of the wireless communication system. An implementation of Serdes is also presented which acts as an interface between the baseband modules and the RF front end.

Diploma thesis is about narrowband PLC communication standards. The theoretical part describes details of all available OFDM standards including G3-PLC, PRIME, IEEE-1901.2 and G.hnem. The practical part deals with PRIME and G3-PLC standards. In this part is also compared OFDM technology with system of single carrier frequency in environment with real interferences. The last part describes developement of two firmwares for PLC modems Texas Instruments TMDSPLCKIT-V3, which allow UART communication and remote data collection. The thesis also includes Windows application developed to display and save collected data.

CAPES / Nesta Tese de Doutorado propõe-se um modelo de consumo de energia para redes acústicas subaquáticas que leva em consideração as especificidades do ambiente subaquático, como a comunicação utilizando ondas acústicas, a dependência da largura de banda do canal com a perda de percurso, que varia tanto com a distância quanto com a frequência, e o ruído. O desvanecimento, resultado do multipercurso, normalmente modelado pelas distribuições Rayleigh e Rice nas transmissões terrestres, é modelado pela distribuição K, que melhor representa a severidade do ambiente subaquático. O modelo considera uma rede subaquática linear de múltiplos saltos e a possibilidade de retransmissões para calcular a energia total consumida para cada bit de informação transmitido com sucesso entre a fonte e o destino. A fim de obter o menor consumo de energia, a SNR e a frequência de operação também são otimizadas, sendo considerado o uso de códigos convolucionais, cuja taxa ótima que leva ao menor consumo é determinada. Uma análise teórica é desenvolvida para cenários com e sem limitação de atraso. No primeiro caso avalia-se o consumo de energia quando retransmissões não são permitidas ou devem ser limitadas e, portanto, uma FER residual deve ser tolerada. No segundo caso infinitas retransmissões são permitidas até que um pacote seja recebido sem erros. Para ambos cenários o número ótimo de saltos que minimiza o consumo de energia é determinado, e na sequência o impacto do número de tentativas de transmissão é considerado. Resultados numéricos são apresentados, mostrando que o esquema de múltiplos saltos é mais eficiente em termos de consumo de energia que a transmissão direta. Além disso, os resultados mostram que um número pequeno de tentativas de transmissão é suficiente para alcançar uma redução considerável no consumo de energia em redes de múltiplos saltos, limitando o atraso médio por pacote transmitido, o que é muito interessante em aplicações reais. / In this Thesis, an energy consumption model for underwater acoustic networks is proposed. The model takes into account the specificities of the underwater environment, such as the use of acoustic waves for communication, dependence of the underwater acoustic channel bandwidth with the path loss, which varies with both the distance and frequency, and noise. The fading, usually modeled by Rayleigh and Rice distributions on terrestrial communications, in this work, is modeled by the K distribution, which best represents the severity of the underwater environment. The model considers a linear multi-hop underwater network and the possibility of retransmissions to calculate the total energy consumed for each bit of information successfully transmitted between the source and the destination. In order to obtain the minimum energy, the SNR and the operating frequency are also optimized. The use of convolutional codes is considered and the optimal code rate, which leads to the minimum energy consumption, is determined. A theoretical analysis was developed for two scenarios: delay constrained and delay unconstrained networks, indicating the optimal number of hops which minimizes energy consumption. Next, the impact of the number of transmission trials was considered. A numerical analysis was also performed for both the scenarios. The numerical results validate the theoretical analysis, showing that the multi-hop scheme is more efficient in terms of energy consumption when compared to direct transmission. Furthermore, the results show that a small number of transmission trials is sufficient to achieve a considerable reduction in energy consumption in multi-hop networks, limiting the average delay per packet transmitted, which is very interesting in real applications.