Due to entropy and Van der Waals¡¦ interaction, carbon nanotubes tend to aggregate degrading their excellent opto-electronic properties and limiting their applications. Chemical derivatizations were applied to the multi-wall carbon nanotube (MWCNT) by esterificating with different lengths of aliphatic pendants (COOC4H9, COOC10H21, and COOC18H37) to decrease the MWCNT aspect ratio to facilitate its dispersion, and to observe its percolation behavior. FTIR analysis revealed the more relevant absorption peaks of C-H at 2917 cm-1, 2846 cm-1 and C=O at 1733 cm-1 from the derivatization. H1-NMR showed that the aliphatic pendant functionalized MWCNT from the signals of OCH2 at £_ = 3.64 ppm, CH2 at £_ = 1.25 ppm, and CH3 at £_ = 0.88 ppm. Raman scattering indicated that esterification caused the ID/IG absorption peak area ratio to decrease. In applications, the electric conductivity was measured on thin-films of MWCNT:Poly-(3-hexylthiophene) (P3HT) as a function of nanotube content. Accompanied with nanotube doping concentration increased, the electric conductivity parallel to film surface (£m||) could range from an undoped value 1.4¡Ñ10-6 S/cm up to 1.2¡Ñ10-2 S/cm. The conductivity percolation threshold concentration decreased as the MWCNT aspect ratio increased due to the average distance between the nanotubes becoming sufficiently small for charges to hopping through P3HT. By incorporating [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM), bulk heterojunction photovoltaic (PV) cells of ITO/PEDOT:PSS/MWCNT:[PC61BM:P3HT]/LiF/Al were fabricated. By varying the ratio of MWCNT to the PC61BM:P3HT (0.8:1) mixtures, the PV cells showed the maximum power conversion efficiency (£bp) close to 4 % with MWCNT-COOC4H9 at a doping concentration of 0.01 wt. %.

Polymer light emitting diodes (PLED) were using a heterocyclic aromatic rigid-rod polymer poly-p-phenylene-benzobisoxazole (PBO) as an opto-electronically active layer; and poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonic acid) (PEDOT:PSS) as a hole transporting layer. Aluminum (Al) and indium tin oxide (ITO) were served as device cathode and anode, respectively. [6,6]-phenyl C61-butyric acid methyl ester (PC61BM) or derivatized multi-wall carbon nano-tube (MWCNT-C18), with great electron transporting ability, was doped into PBO to enhance the performance of PLED devices as well as the thin-film electrical conductivity. The optical length was changed by using different spin coating speeds and durations. From the research, the £fmax of electroluminescence (EL) was blue-shifted as PEDOT:PSS spin coating speed increased for a thinner layer. Once using a higher spin coating speed repeatedly to coat PEDOT:PSS, the £fmax of electroluminescence was red-shifted. If the PEDOT:PSS film thicknesses were similar, the EL spectra were almost the same, independent of device processing scheme. The injection current and EL intensity were enhanced by doping PC61BM or MWCNT- C18. The electric conductivity parallel to film surface (£m¡ü) was increased as the doping concentration increased. Because of the extremely different aspect ratio, the MWCNT-C18 had a lower percolation threshold concentration. Therefore, at a low MWCNT-C18 doping concentration, the injection current and the EL intensity were enhanced compared with those of PC61BM.

Vascularization of thick engineered tissue and organ constructs like the heart, liver, pancreas or kidney remains a major challenge in tissue engineering. Vascularization is needed to supply oxygen and nutrients and remove waste in living tissues and organs through a network that should possess high perfusion ability and significant mechanical strength and elasticity. In this thesis, we introduce a fabrication process to print vascular conduits directly, where conduits were reinforced with carbon nanotubes (CNTs) to enhance their mechanical properties and bioprintability. The generation of vascular conduit with a natural polymer hydrogel such as alginate needs to have improved mechanical properties in order to biomimic the natural vascular system. Carbon nanotube (CNT) is one of the best candidates for this goal because it is known as the strongest material and possesses a simple structure. In this thesis, multi-wall carbon nanotube (MWCNT) is dispersed homogenously in the hydrogel and fabricated through an extrusion-based system.In vitro evaluation of printed conduits encapsulated in human coronary artery smooth muscle cells was performed to characterize the effects of CNT reinforcement on the mechanical, perfusion and biological performance of the conduits. Perfusion and permeability, cell viability, extracellular matrix formation and tissue histology were assessed and discussed, and it was concluded that CNT-reinforced vascular conduits provided a foundation for mechanically appealing constructs where CNTs could be replaced with natural protein nanofibers for further integration of these conduits in large-scale tissue fabrication. It was concluded that MWCNT has a significant effect on mechanical properties, vascular conduit swelling ratio and biological characterization in short-term and long-term cellular viability.

Este estudo teve como objetivo principal desenvolver uma técnica para síntese de um nanocompósito de Y-TZP/MWCNT-COOH (Zircônia estabilizada por 3 mol% de ítria reforçada por nanotubos de carbono funcionalizado em -COOH) com propriedades mecânicas e ópticas que permitam a sua futura utilização como infraestrutura de próteses fixas dentárias e pilares protéticos para implantes. Assim, foram avaliados a microestrutura, resistência à flexão, tenacidade à fratura, limite de fadiga e propriedades ópticas do nanocompósito e comparada àquelas medidas para Y-TZP convencional (controle). O material Y-TZP/MWCNT-COOH foi desenvolvido pelo processo de co-precipitação de hidróxidos mistos associado ao tratamento hidrotérmico/solvotérmico e prensagem uniaxial em formato de blocos para sistemas CAD/CAM. O pó de MWCNT-COOH foi caracterizado por meio de MEV-FEG, TEM, TGA, DRX e FRX previamente a sua utilização para desenvolvimento do nanocompósito. Espécimes foram obtidos a partir do material Y-TZP/MWCNT-COOH para caracterização por meio de DRX, MEV-FEG e TEM, e comparação de suas propriedades estruturais (densidade e contração), ópticas, resistência à flexão, tenacidade à fratura e limite de fadiga com a Y-TZP convencional. O MWCNT-COOH apresentou-se em feixes de nanotubos de carbono recobertos por sílica tendo comprimento médio de 5,10 ± 1,34 ?m, com 90% dos comprimentos medidos (D90) estando abaixo de 6,9 ?m. Foi verificado a não possibilidade da utilização de líquidos orgânicos em nenhum passo da fabricação dos compósito Y-TZP/MWCNT-COOH por levar ao escurecimento do compósito, inviabilizando sua futura aplicação clínica. O tratamento hidrotérmico sem uso de líquidos orgânicos mostrou-se eficaz em proporcionar o revestimento do nanotubo de carbono por partículas de óxido de zircônio e ítrio. Entretanto, ocasionou a formação de aglomerados e partículas de Y-TZP com tamanho maiores que 5 ?m. Uma densidade relativa de 97,4% foi alcançada para o compósito experimental de Y-TZP contendo MWCNT-COOH, tendo uma razão de contraste de 0.9929 ± 0.0012 e um valor de diferença de cor da Y-TZP convencional de 6,1 ± 3,1 ( ?E). As propriedades mecânicas da Y-TZP/MWCNT-COOH, dureza Vickers (10,14 ± 1,27 GPa; p=0,25) e tenacidade à fratura (4,98 ± 0,30 MPa.m1/2; p=0,39), não apresentaram diferença significativa da Y-TZP convencional (dureza: 8,87 ± 0,89; tenacidade à fratura: 4,98 ± 0,30 MPa.m1/2). Entretanto, para a resistência à flexão (p=0,003) e limite de fadiga cíclica (LFC) foram obtidos valores inferiores para o material experimental Y-TZP/MWCNT-COOH (resistência à flexão: 299,4 ± 30,5 MPa; LFC: 179,4 ± 22,5 MPa) quando comparado à Y-TZP controle (resistência à flexão: 623,7 ± 108,8 MPa; LFC: 439,0 ± 56,4 MPa). Com base nos resultados apresentados, é possível concluir que a síntese de um nanocompósito de Y-TZP/MWCNT-COOH com propriedades ópticas adequadas para aplicação na odontologia restauradora foi possível por meio dos métodos descritos, entretanto algumas adequações nos métodos de síntese e processamento para criação do nanocompósito devem ser realizadas para se evitar a acentuada diminuição de importantes propriedades mecânicas do material. / This study aim was to develop a technique for synthetize nanocomposite of Y-TZP/MWCNT-COOH (3 mol% Yttria-Stabilized Tetragonal Zirconia reinforced with COOH functionalized carbon nanotubes) with mechanical and optical properties that allow their future use as fixed dental prosthesis infrastructure and implant abutments. Thus, the following properties of the nanocomposite were investigated and compared to those measured for conventional Y-TZP (control): microstructure, flexural strength, fracture toughness, fatigue limit and optical properties. Y-TZP/MWCNT-COOH material was developed by the co-precipitation of mixed hydroxides associated with the hydrothermal/solvothermal treatment and uniaxial pressing to form blocks for CAD/CAM systems. The MWCNT-COOH powder was characterized by SEM-FEG, TEM, TGA, XRD and XRF prior to its use for the development of nanocomposite. Specimens were obtained from the Y-TZP/MWCNT-COOH material and characterized by XRD, SEM-FEG and TEM. After characterization, the material had their structural properties (density and contraction), optical, flexural strength, fracture toughness and fatigue limit compared to a conventional Y-TZP. The MWCNT-COOH material was observed to be a bundle formation of carbon nanotube covered with silica with an average length of 5.10 ± 1.34 ?m, with 90% of the measured lengths (D90) being below 6.9 ?m. It has been found to be not possible to use organic liquids on any step of the Y-TZP/MWCNT-COOH manufacturing process due to darkening of the composite, making it unfeasible to future clinical application. The hydrothermal treatment without the use of organic liquids was effective in providing the carbon nanotube coating by zirconium and yttrium oxide particles. However, this treatment led to the formation of agglomerates and particles of Y-TZP with larger than 5 ?m. A relative density of 97.4% was achieved for the Y-TZP/MWCNT-COOH composite, having a contrast ratio of 0.9929 ± 0.0012, and a color difference value from the conventional Y-TZP of 6.1 ± 3.1 (?E). The mechanical properties of Y-TZP/MWCNT-COOH, Vickers hardness (10.14 ± 1.27 GPa; p = 0.25) and fracture toughness (4.98 ± 0.30 MPa.m1/2; p = 0.39), showed no significant difference from the conventional Y-TZP (hardness: 8.87 ± 0.89; fracture toughness: 4.98 ± 0.30 MPa.m1/2). However, flexural strength (p = 0.003) and cyclic fatigue limit (CFL) showed lower values for the experimental material Y-TZP/MWCNT-COOH (flexural strength: 299.4 ± 30.5 MPa; CFL: 179.4 ± 22.5 MPa) compared to Y-TZP control (flexural strength: 623.7 ± 108.8 MPa; CFL: 439.0 ± 56.4 MPa). Based on the results presented, it could be conclude that the synthesis of a nanocomposite of Y-TZP/MWCNT-COOH with optical properties suitable for application in restorative dentistry was made possible by the described methods, however some adjustments in synthesis and processing methods for the nanocomposite creation should be taken; to avoid the sharp decrease of important mechanical properties of the material.

Este estudo teve como objetivo principal desenvolver uma técnica para síntese de um nanocompósito de Y-TZP/MWCNT-COOH (Zircônia estabilizada por 3 mol% de ítria reforçada por nanotubos de carbono funcionalizado em -COOH) com propriedades mecânicas e ópticas que permitam a sua futura utilização como infraestrutura de próteses fixas dentárias e pilares protéticos para implantes. Assim, foram avaliados a microestrutura, resistência à flexão, tenacidade à fratura, limite de fadiga e propriedades ópticas do nanocompósito e comparada àquelas medidas para Y-TZP convencional (controle). O material Y-TZP/MWCNT-COOH foi desenvolvido pelo processo de co-precipitação de hidróxidos mistos associado ao tratamento hidrotérmico/solvotérmico e prensagem uniaxial em formato de blocos para sistemas CAD/CAM. O pó de MWCNT-COOH foi caracterizado por meio de MEV-FEG, TEM, TGA, DRX e FRX previamente a sua utilização para desenvolvimento do nanocompósito. Espécimes foram obtidos a partir do material Y-TZP/MWCNT-COOH para caracterização por meio de DRX, MEV-FEG e TEM, e comparação de suas propriedades estruturais (densidade e contração), ópticas, resistência à flexão, tenacidade à fratura e limite de fadiga com a Y-TZP convencional. O MWCNT-COOH apresentou-se em feixes de nanotubos de carbono recobertos por sílica tendo comprimento médio de 5,10 ± 1,34 ?m, com 90% dos comprimentos medidos (D90) estando abaixo de 6,9 ?m. Foi verificado a não possibilidade da utilização de líquidos orgânicos em nenhum passo da fabricação dos compósito Y-TZP/MWCNT-COOH por levar ao escurecimento do compósito, inviabilizando sua futura aplicação clínica. O tratamento hidrotérmico sem uso de líquidos orgânicos mostrou-se eficaz em proporcionar o revestimento do nanotubo de carbono por partículas de óxido de zircônio e ítrio. Entretanto, ocasionou a formação de aglomerados e partículas de Y-TZP com tamanho maiores que 5 ?m. Uma densidade relativa de 97,4% foi alcançada para o compósito experimental de Y-TZP contendo MWCNT-COOH, tendo uma razão de contraste de 0.9929 ± 0.0012 e um valor de diferença de cor da Y-TZP convencional de 6,1 ± 3,1 ( ?E). As propriedades mecânicas da Y-TZP/MWCNT-COOH, dureza Vickers (10,14 ± 1,27 GPa; p=0,25) e tenacidade à fratura (4,98 ± 0,30 MPa.m1/2; p=0,39), não apresentaram diferença significativa da Y-TZP convencional (dureza: 8,87 ± 0,89; tenacidade à fratura: 4,98 ± 0,30 MPa.m1/2). Entretanto, para a resistência à flexão (p=0,003) e limite de fadiga cíclica (LFC) foram obtidos valores inferiores para o material experimental Y-TZP/MWCNT-COOH (resistência à flexão: 299,4 ± 30,5 MPa; LFC: 179,4 ± 22,5 MPa) quando comparado à Y-TZP controle (resistência à flexão: 623,7 ± 108,8 MPa; LFC: 439,0 ± 56,4 MPa). Com base nos resultados apresentados, é possível concluir que a síntese de um nanocompósito de Y-TZP/MWCNT-COOH com propriedades ópticas adequadas para aplicação na odontologia restauradora foi possível por meio dos métodos descritos, entretanto algumas adequações nos métodos de síntese e processamento para criação do nanocompósito devem ser realizadas para se evitar a acentuada diminuição de importantes propriedades mecânicas do material. / This study aim was to develop a technique for synthetize nanocomposite of Y-TZP/MWCNT-COOH (3 mol% Yttria-Stabilized Tetragonal Zirconia reinforced with COOH functionalized carbon nanotubes) with mechanical and optical properties that allow their future use as fixed dental prosthesis infrastructure and implant abutments. Thus, the following properties of the nanocomposite were investigated and compared to those measured for conventional Y-TZP (control): microstructure, flexural strength, fracture toughness, fatigue limit and optical properties. Y-TZP/MWCNT-COOH material was developed by the co-precipitation of mixed hydroxides associated with the hydrothermal/solvothermal treatment and uniaxial pressing to form blocks for CAD/CAM systems. The MWCNT-COOH powder was characterized by SEM-FEG, TEM, TGA, XRD and XRF prior to its use for the development of nanocomposite. Specimens were obtained from the Y-TZP/MWCNT-COOH material and characterized by XRD, SEM-FEG and TEM. After characterization, the material had their structural properties (density and contraction), optical, flexural strength, fracture toughness and fatigue limit compared to a conventional Y-TZP. The MWCNT-COOH material was observed to be a bundle formation of carbon nanotube covered with silica with an average length of 5.10 ± 1.34 ?m, with 90% of the measured lengths (D90) being below 6.9 ?m. It has been found to be not possible to use organic liquids on any step of the Y-TZP/MWCNT-COOH manufacturing process due to darkening of the composite, making it unfeasible to future clinical application. The hydrothermal treatment without the use of organic liquids was effective in providing the carbon nanotube coating by zirconium and yttrium oxide particles. However, this treatment led to the formation of agglomerates and particles of Y-TZP with larger than 5 ?m. A relative density of 97.4% was achieved for the Y-TZP/MWCNT-COOH composite, having a contrast ratio of 0.9929 ± 0.0012, and a color difference value from the conventional Y-TZP of 6.1 ± 3.1 (?E). The mechanical properties of Y-TZP/MWCNT-COOH, Vickers hardness (10.14 ± 1.27 GPa; p = 0.25) and fracture toughness (4.98 ± 0.30 MPa.m1/2; p = 0.39), showed no significant difference from the conventional Y-TZP (hardness: 8.87 ± 0.89; fracture toughness: 4.98 ± 0.30 MPa.m1/2). However, flexural strength (p = 0.003) and cyclic fatigue limit (CFL) showed lower values for the experimental material Y-TZP/MWCNT-COOH (flexural strength: 299.4 ± 30.5 MPa; CFL: 179.4 ± 22.5 MPa) compared to Y-TZP control (flexural strength: 623.7 ± 108.8 MPa; CFL: 439.0 ± 56.4 MPa). Based on the results presented, it could be conclude that the synthesis of a nanocomposite of Y-TZP/MWCNT-COOH with optical properties suitable for application in restorative dentistry was made possible by the described methods, however some adjustments in synthesis and processing methods for the nanocomposite creation should be taken; to avoid the sharp decrease of important mechanical properties of the material.

Field emission is the emission of electrons from a solid under an intense electric field, of the order of 109 V/m. Emission occurs by the quantum mechanical tunneling of electrons through a potential barrier to vacuum. Field emission sources offer several attractive features such as instantaneous response to field variation, resistance to temperature fluctuation and radiation, a high degree of focusing ability in electron optics, good on/off ratio, ballistic transport, and a nonlinear current-voltage relationship. Carbon nanotubes (CNTs) are potential candidates as field emitters since they possess high aspect ratio and are chemically inert to poisoning, and physically inert to sputtering during field emission. They can carry a very high current density and do not suffer field-induced tip sharpening like metallic tips. In addition, the CNT field emitters have the advantage of charge transport through 1D channels and electron emission at the sharp tips due to large enhancement. But the injection of electrons from the back contact remains a technical challenge which requires binding of CNT emitters to metallic substrate. Also, detachment of the CNT from the substrate tends to occur with time. The electrically conducting mixtures of CNTs and polymer can provide an alternative route to address these issues in the field emission of CNTs. The composites can be casted on any substrate in desired shape and the polymer matrix provides necessary support. The research work reported in this thesis includes the preparation of high quality multiwall carbon nanotubes (MWCNTs), MWCNT-polystyrene (PS) composites, and experimental investigation on field emission properties of MWCNT¬PS composites in two different configurations. Electrical conductivity and percolation threshold of the MWCNT-PS composites are also investigated to ensure their high quality prior to the field emission studies. The study has been further extended to reduced graphene oxide (rGO) coated on polymer substrate. The main results obtained in present work are briefly summarized below. This thesis contains eight chapters. Chapter 1 provides an overview of basics of field emission, and the potential of CNT and CNT-polymer composites as field emitters. Chapter 2 deals with the concise introduction of various structural characterization tools and experimental techniques employed in this study. Chapter 3 describes the synthesis of MWCNTs and characterization by using electron microscopy and Raman spectroscopy. MWCNTs are synthesized by chemical vapor deposition (CVD) of toluene [(C6H5) CH3] and ferrocene [(C5H5)2 Fe] mixture at 980 °C. Here toluene acts as carbon source material and ferrocene provides catalytic iron (Fe) particles. The MWCNT formation is based on the thermal decomposition of the precursor mixture. Scanning electron microscopy (SEM) characterization shows that the MWCNTs are closely packed and quite aligned in one direction. The average length of MWCNTs is about 200 μm and outer diameter lies in the range of 50-80 nm. The high quality of as-prepared MWCNT sample is confirmed by Raman spectroscopy. The as-grown MWCNTs are encapsulated with catalytic Fe nanoparticles, revealed by transmission electron microscopy. The Fe nanoparticles trapped within the MWCNT serve as fantastic system for studying the magnetic properties. Three types of MWCNT samples filled with Fe nanoparticles of different aspect ratio (~10, 5 and 2) are synthesized by varying the amount of ferrocene in the precursor material, and their magnetic properties are investigated. Enhanced values of coercivity (Hc) are observed for all samples, Hc being maximum (~2.6 kOe) at 10 K. The enhancement in Hc values is attributed to the strong shape anisotropy of Fe nanoparticles and significant dipolar interactions between Fe nanoparticles. Chapter 4 deals with the field emission studies of MWCNT-PS composites in the parallel configuration. By incorporating as-prepared MWCNTs in PS matrix in a specific ratio, composites with varying loading from 0.01-0.45 weight (wt.) fraction are prepared using solution mixing and casting. High degree of dispersion of MWCNTs in PS matrix without employing any surfactant is achieved by ultrasonication. Low percolation threshold (~0.0025 wt. fraction) in the MWCNT-PS composites ensures the good connectivity of filler in the fabricated samples. Field emission of MWCNT¬PS composites is studied in two different configurations: along the top surface of the film (parallel configuration) and along the cross section of the sample (perpendicular configuration). In this chapter field emission results of the MWCNT-PS composites in parallel configuration are presented. The effect of charge transport in limiting the field emission of MWCNT-PS composite is discussed. Field emission results of MWCNT-PS composites in parallel configuration indicate that the emission performance can be maximized at moderate wt. fraction of MWCNT (0.15). The obtained current densities are ~10 µA/cm2 in the parallel configuration. Chapter 5 presents the study of field emission characteristics of MWCNT¬PS composites of various wt. fractions in the perpendicular configuration. Till date most studies using nanotube composites tend to have the nanotubes lying in two dimensional plane, perpendicular to the applied electric field. In the perpendicular configuration, the nanotubes are nearly aligned parallel to the direction of the applied electric field which results in high field enhancement, and electron emission at lower applied fields. SEM micrographs in cross-sectional view reveal that MWCNTs are homogeneously distributed across the thickness and the density of protruding tubes can be scaled with wt. fraction of the composite film. Field emission from composites has been observed to vary considerably with density of MWCNTs in the polymer matrix. High emission current density of 100 mA/cm2 is achieved at a field of 2.2 V/µm for 0.15 wt. fraction. The field emission is observed to follow the Fowler– Nordheim tunneling mechanism, however, electrostatic screening plays a role in limiting the current density at higher wt. fractions. Chapter 6 highlights the field emission response of rGO coated on a flexible PS film. Field emission of rGO coated PS film along the cross section of the sample is studied in addition to the top film surface of the film. The effect of geometry on the improved field emission efficiency of rGO coated polymer film is demonstrated. The emission characteristics are analyzed by Fowler–Nordheim tunneling for field emission. Low turn-on field (~0.6 V/µm) and high emission current (~200 mA/cm2) in the perpendicular configuration ensure that rGO can be a potential field emitter. Furthermore, stability and repeatability of the field emission characteristics are also presented. Chapter 7 deals with the synthesis, characterization, and field emission of two different kinds of hybrid materials: (1) MWCNT coated with zinc oxide (ZnO) nanoparticles (2) ZnO/graphitic carbon (g-C) core-shell nanowires. The field emission from the bucky paper is improved by anchoring ZnO nanoparticles on the surface of MWCNT. A shift in turn on field from 3.5 V/µm (bucky paper) to 1.0 V/µm is observed by increasing the ZnO nanoparticle loading on the surface of MWCNT with an increase in enhancement factor from 1921 to 4894. Field emission properties of a new type of field emitter ZnO/g-C core-shell nanowires are also presented in this chapter. ZnO/g-C core/shell nanowires are synthesized by CVD of zinc acetate at 1300 °C. Overcoming the problems of ZnO nanowire field emitters, which in general possess high turn on fields and low current densities, the core-shell nanowires exhibit excellent field emission performance with low turn on field of 2.75 V/µm and high current density of 1 mA/cm2. Chapter 8 presents a brief summary of the important results and future perspectives of the work reported in the thesis.