This dissertation systematically explores multiple-input converters (MICs) configuration and topologies, and then proposes improvements on certain beneficial MICs—time-sharing MICs and soft-switching MICs for distributed generation (DG) applications with high voltage transfer ratio. Compared with other MIC families which are derived from same input and output cells, time-sharing MICs have the fewest circuit components. However, time-sharing MICs lack for bi-directional power flow capability due to their special input switches requirement. In addition, their hard-switching characteristic leads to a low efficiency problem when isolation is necessary. The dissertation investigates into time-sharing MIC input switch selection, which leads to a new driving strategy and new input switch combinations. With the new input switch combinations, bi-directional and high efficiency time-sharing MICs are made possible. Besides isolated time-sharing MIC, Soft-switching MICs might also be a common choice for high voltage transfer ratio DG applications. However, the enormous amount of circuit components makes the soft-switching MICs become less attractive. An input cell reduction method is introduced in this dissertation to greatly reduce the component count of isolated MICs, including soft-switching MICs. In addition to the improvement on existing MIC families, a new push-pull connected MIC family is proposed in this dissertation as another choice of high voltage transfer ratio DG applications. Moreover, a comparison among MIC families is made to provide a sense of topologies selection in certain applications. Prototypes of time-sharing dual-input (DI) SEPICs, a push-pull connected DI-Boost converter, and a DI full-bridge (FB) converter are built to verify aspects discussed in this dissertation. Bi-directional power flow capability of time-sharing MIC is confirmed with a time-sharing DI-SEPIC and a soft-switching time-sharing MIC is realized by an isolated time-sharing DI-SEPIC with an active clamping leg. Maximum power point tracking control feasibility in these converters is evaluated with real photovoltaic modules that are connected to the push-pull connected DI-Boost converter that uses a perturb-and-observe method. Finally, an efficiency comparison is made between time-sharing MIC and push-pull connected MIC. / text

In this thesis, the possibility of applying digital current mode control on multiple-input (MI) converters is studied. As for MI topologies having a central energy transfer inductor, the predictive constant on-time current-mode control can greatly reduce both the design and digital realization efforts needed. By doing digital constant on-time current-mode control, the control of MI buck and MI buck-boost converters can be simplified into an equivalent-single-input converter control problem. The small signal models of digital constant on-time controlled single-input (SI), MI buck and SI, MI buck-boost converters in both CCM and DCM are proposed. Simulations and experiments were built to verify the proposed models. / text

Nowadays, the number of applications which need more than one power source is increasing. Distributed generating systems or micro-grid systems normally use more than one power source or more than one kind of energy source. Also, to increase the utilization of renewable energy sources, diversified energy source combination is recommended. For example, a wind-photovoltaic generating system, a combination of a wind generator and photovoltaic array, can give a greater degree of freedom when choosing the install location. The combination of more power sources and diversified power sources makes it possible to obtain higher availability in a power system. A parallel connection of converters has been used to integrate more than one energy source in a power system. However, a multiple-input converter (MIC) can generally have the following advantages compare to a combination of several individual converters; (1) cost reduction, (2) compactness, (3) more expandability and (4) greater manageability. First, this research suggests MIC topology comparison criteria that can be used as a decision guide for choosing a MIC topology depending on the application. Even though there are some MIC topology classification methods such as by the kind of combining methods, the classification methods are not enough to choose one particular topology. The comparison criteria presented in this dissertation are practical enough to decide which topology is suitable and should be chosen. Second, a new MI modified inverse Watkins-Johnson converter (MIMIWJC) without a coupled inductor is proposed. The circuit configuration of this converter and its operation principles are described, including the open-loop and closed-loop circuit. For control purposes, a small signal model of the proposed converter is developed using Middlebrook’s extra element theorem. In addition, two possible control methods are introduced in this dissertation. Finally, the theoretical analysis of the proposed converter is verified with simulations and experiments. / text