This research provides a new insight on various properties, such as rheological, mechanical, and flame-retarding properties, as well as the foaming behaviors of wood flour /plastic composites (WPCs) through the addition of a small amount of nanosized clay particles. Although WPCs have replaced natural wood in many applications, their industrial usage has been limited because of their weak modulus, low impact strength, low screwing-ability/nailing-ability, high density compared to natural wood, as well as their flammability compared to plastics. In this context, the incorporation of nanoclay and foam structure into WPC has been studied to dramatically alleviate these drawbacks. The melt blending method was used to prepare different types of clay-filled wood flour composites such as intercalated and exfoliated clay nanocomposites. The effects of key processing variables such as the mixing time, mixing temperature and screw speed on clay dispersion were investigated from the thermodynamic and kinetic point of view. Their nanostructure was determined by using X-ray diffraction (XRD) and transmission electron microscopy (TEM). Accordingly, effective strategies for controlling intercalation and exfoliation of polyolefin/clay nanocomposites were proposed and evaluated. Wood flour composites with high levels of clay dispersion were synthesized successfully using a general new route (i.e., maleated-polyolefin-based clay masterbatch and dilution). The effects of nanoclay particles on the rheological, thermal, and mechanical properties were identified. In addition, it was demonstrated that a small amount of well-dispersed nanoclay in WPC significantly improved flame retardancy of WPCs. The mechanism of improved flame-retarding effects on nanoparticles was elucidated as well. The relationship between the clay dispersion and the material properties were also clarified. Furthermore, the foaming behaviors of HDPE-based and PP-based wood flour/nanoclay composites were investigated using N2 as the blowing agent in an extrusion process. The cell nucleation and growth behaviors of wood flour/polyolefin/clay composite foams were elucidated while varying the temperature, pressure, wood flour content, clay content and dispersion degrees.

Basic physics teaches us that the frictional force (lateral force) needed to move objects on surfaces are proportional to load (normal force) – Amonton’s Laws. In tribology, this force is proportional to contact area, whereas Amonton is just a special case for contact area scaling with load. Such established laws do not seem to apply to small drops on flat, smooth surfaces in which frictional forces have an inverse relation to contact area and have time component prior to movement. Such phenomena can be explained by Shanahan-deGennes were intermolecular forces are considered for a deformed surface. Graphene is a special case where no time component is observed and frictional forces are attributed to its chemical homogeneity and stability. In the second part of this thesis, graphene is considered as nanofiller to build up polymer nanocomposites via Layer by Layer (LbL). Graphene Nanoribbons derived from multi-walled carbon nanotubes (MWCNT) offers a special case for thermoplastic polyurethane nanocomposites in that of thermally activated twisting morphology influences nanocomposite properties. Finally an electric field driven transdermal hydrogel drug delivery device has been demonstrated by just using CNTs, polyvinyl-borax gel and a CNT membrane

The aims of this thesis are to fabricate the single-edged Ti/APC-2 hybrid composite laminates with and without(w/wo) nanoparticles and to investigate their mechanical properties due to tensile and cyclic tests. The composite laminates were three-layered laminates with one 0.55 mm thick APC-2 lay-ups covered by two 0.5 mm thick Grand 1 titanium alloy sheets. Nanoparitcles SiO2 were dispersed uniformly on the interfaces of APC-2 with optimal amount of 1wt%. The APC-2 was stacked according to cross-ply [0/90]s sequences. The titanium sheet surface was treated by chromic acid anodic method to achieve perfectly bonding with matrix PEEK. The modified diaphragm curing process was adopted to cure Ti/APC-2 hybrid composite laminates. The cutting of single-edged cracks with Electrical Discharge Machine, such as 1.5 mm and 3.0mm and 4.5 mm and 6.0 mm. The MTS 810 material testing machine was used to conduct all the tests. The mechanical properties, such as ultimate tensile strength, longitudinal stiffness of composite laminates w/wo nanocomposite laminate were obtained from the static tensile tests. The stress-strain diagrams were plotted in laminates for the corresponding single-edged crack. The constant stress amplitude tension-tension cyclic tests were carried out by using load-control mode at a sinusoidal loading wave with frequency of 5Hz and stress ratio R=0.1. The received fatigue data were plotted in S-N curves for different single-edged crack. From the results, the conclusion were summarized. First, both ultimate strengths of Ti/APC-2 composite laminates and nanocomposite laminates are very close. Second, Ti/APC-2 cross-ply nanocomposite laminates have better fatigue resistance than that of Ti/APC-2 cross-ply composite laminates.

Health monitoring is an important field as small failures can build up and cause a catastrophic failure. Monitoring the health of a structure can be done by measuring the motion of the structure through the use of strain sensors. The limitations of current strain sensing technology; cost, size, form could be improved. This research intends to improve current strain sensing technology by creating a conductive polymer composite that can be used monitor health in structures. Conductive polymer composites are a viable candidate due to the low costs of manufacturing, tailorable mechanical and electrical properties, and uniform microstructure. This work will focus on determining if a all-polymer composite can be used as a strain sensor, and investigating the effects of filler, doping and latex effect the electrical and strain sensing properties. Strain sensors were prepared from polyaniline (PANI)-latex composites, the morphology, mechanical, electrical and strain sensing properties were evaluated. These strain sensors were capable of repeatable measuring strain to 1% and able to measure strain until the substrates failure at 5% strain, with a sensitivity (measured by gauge factor) of between 6-8 (metal foil strain sensors have a gauge factor of 2). The best performing strain sensor consisted of 4 wt.% polyaniline. This composition had the best combination of gauge factor, linearity, and signal stability. Further experiments were conducting to see if improvements could be made by changing the polymer used for the matrix material, the molecular weight and the level of doping of the polyaniline. Results indicate through differences in strain sensing response; lower hysteresis and unrecoverable conductivity, that polyaniline latex composites can be adjusted to further improve their performance. The polyaniline-latex composites were able to repeatable measure strain to 1%, as well as strain until failure and with gauge factor between 6-8, and a 70% increase in signal at failure. These properties make these composites viable candidates to monitor health in structures, buildings, bridges, and damns.

The fatigue response of mechanical properties and life due to constant stress amplitude tension-tension(T-T)cyclic loading at elevated temperature in nanocomposite APC-2 laminates was investigated. From the basic testing the total amount of 1% by weight of SiO2 spreaded in the interfaces was proved optimally. Related experiments on unidirectional nanocomposite APC-2 laminates were completed, including static tension tests in [0]16¡B[30]16¡B[45]16¡B[60]16 and [90]16 and T-T cyclic tests in [0]16¡B[45]16 and [90]16 specimens at room temperature. After obtaining experimental data, such as ultimate strength and elastic modulus, which were found improved significantly, and then comparing with the basic theory of mechanics of composites, rule of mixtures was adopted to estimate the properties of cross-ply and quasi-isotropic nanocomposite APC-2 laminates and found the largest errors were within 25%. In the consideration of heterogeneous and anisotropic properties of the matrix and the reinforced fibers in nature, the results are reasonably acceptable. On the other hand, the S-N curves according to the experimental data of the fatigue tests were plotted. The vertical axis shows the nondimensional stress level, i.e., the applied maximum stress normalized by ultimate strength at room temperature, and the horizontal axis represents the logarithm of applied cycles. The S-N curves at room and elevated temperatures were also expressed by curve fitting from top to bottom as temperature increasing from RT to 150¢J for both cross-ply and quasi-isotropic nanocomposite laminates. However, when applied maximum stress was normalized by the corresponding ultimate strength, the positions of S-N curves were reverse, i.e., the curves were shown from bottom to top as temperature increasing from RT to 150¢J. That strongly hints us the resistance to fatigue at elevated temperature in both lay-ups of nanocomposite laminates is indeed significantly improved.

This thesis aims to fabricate the high performance Magnesium/Carbon-Fiber/PEEK five-layer hybrid nanocomposite laminates. The adopted Mg thin sheets are 0.5mm thick. The Carbon-Fiber/PEEK prepregs were stacked into two lay-ups, such as cross-ply [0/90]s and quasi-isotropic [0/45/90/-45], with the adding of nanoparticles SiO2 spreaded among the laminates. After etching of Mg foils by CrO3-base etchants, a five-layered Mg/Carbon-Fiber/PEEK nanocomposite laminate was made according to the modified diaphragm curing process. Then, the mechanical properties, such as stress-strain curve, strength and stiffness were obtained by tensile test at room temperature (25¢J), 50, 75, 100, 125 and 150¢J and the fatigue properties were also obtained under constant stress amplitude tension-tension cyclic loading elevated at room and elevated temperatures 25, 75, 100, 125 and 150¢J. Finally, the Mg sheets and fractured laminates were observed by the SEM and OM. The results according to the experiments were summarized as follows: 1.The slope of stress-strain curve dropped at strain¡Ü0.0015. It can be inferred that fracture occurred in the laminates at this time. Stiffness approached the theoretical value by curve fitting with the strain range of 0 to 0.0015. 2.The mechanical properties decreased with the environmental temperature rise. 3.The resistance to the temperature effect of the quasi-isotropic Magnesium/Carbon-Fiber/PEEK laminate is superior to that of the cross-ply Magnesium/Carbon-Fiber/PEEK laminate. 4.The cross-ply Magnesium/Carbon-Fiber/PEEK laminate is brittler than that of the quasi-isotropic laminate generally. 5.The irregular bright lines were found in the third etched Mg sheet and that resulted in the delamination of Mg sheet after treatment. The unetched part maybe the defect of Mg sheet. 6. It was found that AZ31 has the precipitation hardening effect at 50¢J and 75¢J.

Multi-walled carbon nanotubes (MWNTs) are a nanofiller that has desirable multifunctional properties. They have been shown to offer improved mechanical, thermal, and electrical properties in composites. Research has been studying their incorporation into polymer composites. Polyamide 12 is a polyamide of interest that has been manufactured to have lower moisture absorption and higher ductility than other commercial polyamides such as 6 and 6,6 at room temperature. In these studies, MWNTs have been incorporated into polyamide 12 at different weight loadings and using MWNTs with differing outer diameters. The composites were melt processed and characterized using differential scanning calorimetry (DSC) to understand the effects of MWNTs on the crystallization behavior of polyamide 12. A melt peak splitting behavior was observed in the polyamide 12 and composite samples when the specimens were not allowed to fully anneal. Total crystallinity in the samples remained the same between the polyamide 12 and composites when the samples were fully annealed. Total crystallinity increased by 1 to 4 percent in the composites over the polyamide 12 when samples were not fully annealed. The addition of MWNTs to the polyamide 12 system increased the amount of crystallization contained in the lower temperature melting peak. An increase in MWNT concentration resulted in an increase in the crystallinity contained in the lower temperature peak. The addition of smaller diameter MWNTs resulted in a further increase in the lower temperature peak when the outer diameter was below a critical size.

<p>The aim of this study was to determine whether tooth bleaching agents alter the colour of stained direct composite resins.</p>

An anti-reflective (AR) lens is an ultrathin multilayered structure composing of AR coatings on a lens substrate. These coatings can be made by a spin-coating process with a nanocomposite of UV curable acrylic monomers and well dispersed metal oxide nanoparticles. The in-situ UV polymerization rate was reduced by oxygen inhibition and the absorption of UV energy by the metal oxide nanoparticles. There are few studies of the mechanical properties of ultrathin polymeric coatings that include the effects of substrates, the viscoelastic behaviors of polymers in submicron scales and the effects of multilayered coatings. With a coating system based on UV cured dipentaerythritol pentaacrylate on silicon wafer substrates, nanoindentation tests showed that the nominal reduced contact modulus increased with the indentation load and penetration depth due to the effect of the substrate, in quantitative agreement with an elastic contact model. Ultrathin polymeric coatings subjected to constant indentation loads exhibit shear-thinning during flow. None of the models examined completely described the elastic response of an ultrathin polymeric coating on a compliant plastic substrate. The effective modulus was a function of coating-substrate property, indenter tip size, coating thickness, adhesion and residual stress. It was logarithmic dependent on the ratio of the indentation depth to the coating thickness prior to coating fracture. An elastic model, assuming shear-lag and a plane-stress state, was used to estimate the interfacial strength between a submicron coating and a compliant substrate. The critical indentation load for the indentation-induced delamination of the coating from the substrate increased with the third power of the indentation depth and was a linear function of the reciprocal of the coating thickness. The interfacial strength was 70.4 MPa. Mechanical properties and fracture characteristics of CVD ceramic and nanocomposite coatings on polymer substrates were evaluated by nanoindentation and nanoscratching tests. The AR lenses made with polymer nanocomposite coatings have better mechanical properties due to the close match of properties between the coatings and the plastic substrate. The new approach to making AR lenses with polymer nanocomposites on plastic substrate is promising.

At present, one of the key challenges in the light-emitting diode (LED) packaging technology is light extraction due to the difference in index of refraction between LED chip and air. Silicone nanocomposites have been extensively researched for applications in LED encapsulant to reduce such difference in refractive index. It is well-known that silicone is desirable for LED encapsulant because of its optical transparency and photothermal resistance. However, not much has been accomplished to leverage the elastic properties of silicone for enabling a stretchable LED encapsulant. In this work, I aim to investigate the stretch ability of silicone/zinc oxide (ZnO) nanocomposites for LED packaging. Wurtzite ZnO nanoparticles were prepared in colloids and subjected to silane treatment. Effects of both ex situ and in situ silane treatment on the final mechanical and optical properties of the silicone/ZnO nanocomposites were examined. Silicone/ZnO nanocomposites exhibit significantly more compliant stress-strain behavior than silicone control. In particular, silicone/silane-treated ZnO nanocomposites show more serrated stress-strain curves. They also embrace higher transmittance than silicone/unmodified ZnO nanocomposites, indicating an improvement in the dispersion of the nanoparticles. It was found that the silicone/5% silane-treated ZnO nanocomposite prepared by an in situ method was able to deform over a range of up to 160%. The film made of this unique silicone/ZnO nanocomposite (~40 microns thick) exhibits transmittance >70% throughout the visible range.