Energy harvesting using piezoelectric nanomaterials provides an opportunity for advancement towards self-powered systems. Self-powered systems are a new emerging technology, which allows the use of a system or a device that perform a function without the need for external power source like for example, a battery or any other type of source. This technology can for example use harvested energy from sources around us such as ambient mechanical vibrations, noise, and human movement, etc. and convert it to electric energy using the piezoelectric effect. For nanoscale devices, the size of traditional batteries is not suitable and will lead to loss of the concept of “nano”. This is due to the large size and the relatively large magnitude of the delivered power from traditional sources. The development of a nanogenerator (NG) to convert energy from the environment into electric energy would facilitate the development of some self-powered systems relying on nano- devices. The main objective of this thesis is to fabricate a piezoelectric Zinc Oxide (ZnO) NGs for low frequency (˂ 100 Hz) energy harvesting applications. For that, different types of NGs based on ZnO nanostructures have been carefully developed, and studied for testing under different kinds of low frequency mechanical deformations. Well aligned ZnO nanowires (NWs) possessing high piezoelectric coefficient were synthesized on flexible substrates using the low temperature hydrothermal route. These ZnO NWs were then used in different configurations to demonstrate different low frequency energy harvesting devices. Using piezoelectric ZnO NWs, we started with the fabrication of sandwiched NG for hand writing enabled energy harvesting device based on a thin silver layer coated paper substrate. Such device configurations can be used for the development of electronic programmable smart paper. Further, we developed this NG to work as a triggered sensor for wireless system using foot-step pressure. These studies demonstrate the feasibility of using ZnO NWs piezoelectric NG as a low-frequency self-powered sensor, with potential applications in wireless sensor networks. After that, we investigated and fabricated a sensor on PEDOT: PSS plastic substrate either by one side growth technique or by using double sided growth. For the first growth technique, the fabricated NG has been used as a sensor for acceleration system; while the fabricated NG by the second technique has worked as anisotropic directional sensor. This fabricated configurations showed stability for sensing and can be used in surveillance, security, and auto-mobil applications. In addition to that, we investigated the fabrication of a sandwiched NG on plastic substrates. Finally, we demonstrated that doping ZnO NWs with extrinsic element (such as Ag) will lead to the reduction of the piezoelectric effect due to the loss of crystal symmetry. A brief summary into future opportunities and challenges are also presented in the last chapter of this thesis.

Si nanowires have potential applications in a variety of technologies such as micro and nanoelectronics, sensors, electrodes and photovoltaic applications due to their size and specific surface area. Au particle-assisted vapour-liquid-solid or VLS growth method remains the dominant process for Si nanowire growth. A comprehensive kinetic model that addresses all experimental observations and provides a physico-chemical model of the VLS growth method is thus essential. The work done as part of this research is divided into two sections. A steady state kinetic model was first developed for the steady state growth rate of Si nanowires using SiCl4 and SiH4 as precursors. The steady state refers to a balance between the rates of injection and ejection of Si into the Au droplet. This balance results in a steady state supersaturation under which wire growth proceeds. In particular evaporation and reverse reaction of Si from the Au droplet and modes of crystal growth for wire growth have been considered in detail for the first time. The model is able to account for both, the radius independent and radius dependent growth rates reported in the literature. It also shows that the radius dependence previously attributed to purely thermodynamic considerations could also as well be explained just by steady state kinetics alone. Expressions have been derived for the steady state growth rate that require the desolvation energy, activation energy for precursor dissociation and supersaturation prevalent in the particle as inputs for calculation. In order to evaluate this model the incubation and growth of Si nanowires were studied on sapphire substrates in an indigenously built automated MOCVD reactor. Sapphire was chosen as the substrate, as opposed to Si which is commonly used, so as to ensure that the vapour phase is the only source of Si. A classical incubation period for nucleation, of the order of 4-8 minutes, was experimentally observed for the first time. Using the change in this incubation period with temperature a value of 15kT was determined to be the desolvation energy for growth using SiH4. The steady state growth rate of Si nanowires were measured and compared with the predictions of the model using the values of activation energies so determined. The thesis based on the current research work is organized as follows: Chapter 1 introduces the research area followed by a brief outline of the overall work Chapter 2 provides a summary of current literature, and puts the research described in this thesis in perspective. The diameter dependent growth rate of NWs which was initially solely attributed to the Gibbs-Thomson effect is first summarized. Experimental observations to the contrary are then highlighted. These contradictions provided the incentive for the research described in this thesis. Following a summary of the growth rate theories, the experimental observations on incubation available in the literature are summarized. All the other variants of the VLS method are also discussed. Chapter 3 describes the design, construction and working of an indigenously built semi- automated CVD reactor. This CVD reactor was used to conduct the Si NW growth experiments over sapphire substrates. Chapter 4 develops the physical chemistry model for Au catalyzed Si nanowire growth using SiCl4 and SiH4 precursors. The model originated from the contradictions present in the literature over the rate limiting step of the VLS growth mechanism and the steady state growth rate dependence on wire diameter. The development starts with explaining the thermodynamics of the steady state VLS process. The significance of the model lies in the detailed analysis of the all the atomistic process occurring during the VLS growth. In particular the evaporation and reverse reaction of Si from Au-Si droplet is explained in detail and possibly for the first time. Expressions for steady state growth rate by various modes, such as layer by layer growth (LL), by multilayer growth (ML) and growth by movement of a rough interface at the L-S growth interface are derived and presented. Chapter 5 discusses the results which emerge out the kinetic model from the previous chapter. Under a single framework of equations, the model is successful in explaining both the diameter independent and diameter dependent growth of NWs. As one of the major outcomes of the model, the growth rates of Si NWs are predicted and trends in growth rate are found to agree with those experimentally observed. Growth rate dependencies on pressure and temperature are implicitly included in the equations derived. An estimate of supersaturation has been extracted for the first time using the framework of equations. Chapter 6 contains the experimental results of the Si NW growth over sapphire substrates. An incubation period in the order of 3-8 minutes has been observed for Si NW growth on sapphire. The data has been compared with existing literature data and interpreted using classical transient nucleation theory. The incubation period data has been utilized to extract the kinetic parameter, QD, which is the desolvation enegy. These parameters and the measured steady state growth rates have been used to estimate the supersaturation existing in the droplet using the framework developed in chapters 4 and 5. Chapter 7 summarizes the outcome of the current research and highlights the future directions for the research problem addressed in this thesis.

<p> The mechanisms operating during the metal-assisted growth of III-V nanowires (NWs) by molecular beam epitaxy on (1 1 l)B substrates were investigated through a series of experiments aimed at determining the influence of growth conditions on the morphology and crystal structure. Using GaAs as the principal material system for these studies, it is shown that a good control of these two characteristics can be achieved via a tight control of the temperature, V /III flux ratio, and Ga flux. Low and intermediate growth temperatures of 400°C and 500°C resulted in a strongly tapered morphology, with stacking faults occurring at an average rate of 0.1 nm^(-1). NWs with uniform diameter and the occurrence of crystal defects reduced by more than an order of magnitude were achieved at 600°C, a V /III flux ratio of 2.3, and a Ga impingement rate on the surface of 0.07 nm/s, and suggest the axial growth is group V limited. Increasing the flux ratio favored uniform sidewall growth, thus making the process suitable for the fabrication of core-shell structures. Further observation of steps on the sidewall surface of strongly tapered NWs suggests that radial growth of the shell proceeds in a layer-by-layer fashion, with the edge progressing in a step-flow mode toward the tip. </p> <p> From the experimental considerations, an analytical description of the growth is proposed, based on a simple material conservation model. Direct impingement of growth species on the particle, coupled to their diffusion from the sidewall and the substrate surface, are considered in the derivation of expressions for the time evolution of both axial and radial growths. Factors that take into account the nonunity probability of inclusion of group III adatoms in the axially growing crystal are introduced. Moreover, a step-mediated growth is included to describe the axial evolution of the shell. </p> / Thesis / Doctor of Philosophy (PhD)

Compte tenu du récent taux alarmant d'épuisement des réserves de combustibles fossiles et de l'augmentation drastique des niveaux de CO2 dans l'atmosphère qui a conduit au réchauffement de la planète et à des changements climatiques sévères, l'exploitation de toutes sortes d'énergies renouvelables a été la Parmi les principales priorités de la recherche Champs à travers le monde. L'une des nombreuses voies de ce genre est la réduction du CO2 aux combustibles utilisant des énergies renouvelables, plus communément appelées cellules photoélectro-catalytiques (PEC). Des essais expérimentaux sur la réduction du CO2 ont été réalisés sur différents types de catalyseurs dans les deux cellules (Conçu par un laboratoire) afin de comprendre la sélectivité, la productivité et les produits de réaction obtenus. Des essais expérimentaux ont été réalisés sur différents types de catalyseurs à la fois dans les cellules en phase gazeuse et en phase liquide pour comprendre la sélectivité, la productivité et les produits de réaction obtenus. Pour les études sur la réduction EC du CO2 en phase gazeuse, une série d'électrodes (à base de nanoparticules (NPs) de Cu, Fe, Pt et CuFe déposées sur des nanotubes de carbone ou de noir de carbone puis placées à l'interface entre une membrane Nafion et Une électrode à couche de diffusion de gaz). Les résultats démontrent le type divers de produits formés et leurs productivités. Dans des conditions sans électrolyte, la formation de produits ≥C1 tels que l'éthanol, l'acétone et l'isopropanol a été observée la plus élevée étant pour Fe et suivie de près par Pt. Pour améliorer Combustibles nets, un ensemble différent d'électrodes a été préparé sur la base de revêtements MOF de type imidazolate de type zéolitique substitué (SIM-1) (Fe-CNT, Pt-CNT et CuFe-CNT basés sur MOF) Et Pt-MOF a montré des carburants améliorés. En se reportant aux études sur la réduction EC du CO2 dans une cellule en phase liquide, un ensemble similaire d'électrodes a été prepare (NP - Cu, Fe, Pt, Ru, Co déposées sur des nanotubes de carbone ou du noir de carbone ont). Pour les conditions de phase liquide, en termes de produits C nets, les électrodes catalytiques à base de Pt sont en tête de la catégorie, suivies de près par Ru et Cu, tandis que Fe a obtenu la position la plus basse. Le mécanisme réactionnel sous-jacent probable a également été fourni. Afin d'améliorer encore les performances, on a synthétisé des NP de metal (Ru, Fe, Pt et Cu) de différentes tailles en utilisant différentes techniques de synthèse: (i) l'itinéraire d'imprégnation (ImR) pour obtenir des NP dans la plage de tailles de 10 à 50 nm; (Ii) Approche organométallique (OM) pour synthétiser des NPs uniformes et ultrafines dans la plage de tailles de 1-5 nm. Fe ont été synthétisés par une nouvelle voie de synthèse et des conditions pour atteindre des NP de 1 à 3 nm. (Iii) Approche de haut en bas de Nanowire pour obtenir des NP de cuivre ultrafin dans la plage de taille de 2-3,8 nm. Les améliorations apportées à la productivité du carburant se sont révélées être de 5 à 30 fois plus élevées pour les petites NP sur les NP plus importantes et, en outre, une charge réduite de 10 à 1-2% en poids. Un autre ensemble d'électrodes à base de nano-mousses (Cu NF et Fe NF sur Feuille de Cu, Feuille de Foie, Al Foil, Inconel foil et Al grid / mesh) préparés par électrodéposition ont également été étudiés afin d'améliorer encore la conversion de CO2 / carburant. Après, l'optimisation du dépôt et de la tension à l'aide de la voltamétrie cyclique, les carburants se sont améliorés de 2 à 10 fois par rapport aux combustibles nets les plus élevés obtenus à l'aide d'électrodes CNT dopées à base de NP / In view of the recent alarming rate of depletion of fossil fuel reserves and the drastic rise in the CO2 levels in the atmosphere leading to global warming and severe climate changes, tapping into all kinds of renewable energy sources has been among the top priorities in the research fields across the globe. One of the many such pathways is CO2 reduction to fuels using renewable energies, more commonly referred as photo-electro-catalytic (PEC) cells. Experimental tests were carried out on various types of catalysts in both the gas and liquid phase cells (lab-designed) to understand the different selectivity, productivity and the reaction products obtained. For the studies on the EC reduction of CO2 in gas phase cell, a series of electrodes (based on Cu, Fe, Pt and Cu/Fe metal nanoparticles – NPs - deposited on carbon nanotubes – CNTs - or carbon black and then placed at the interface between a Nafion membrane and a gas-diffusion-layer) were prepared. Under gas phase, the formation of ≥C1 products (such as ethanol, acetone and isopropanol) were observed, the highest being for Fe and closely followed by Pt, evidencing that also non-noble metals can be used as efficient catalysts under these conditions. To enhance the net fuels, a different set of electrodes were also prepared based on substituted Zeolitic Imidazolate (SIM-1) type MOF coatings (MOF-based Fe-CNTs, Pt-CNTs and Cu/Fe-CNTs) and Pt-MOF showed improved fuels. Moving to the studies on the EC reduction of CO2 in liquid phase cell, a similar set of electrodes were prepared (metal NPs of Cu, Fe, Pt, Ru and Co deposited on CNTs or carbon black). For liquid phase conditions, in terms of net C-products, catalytic electrodes based on Pt topped the class, closely followed by Ru and Cu, while Fe got the lowest position. The probable underlying reaction mechanism was also provided. In order to improve further the performances, varied sized metal NPs (Ru, Fe, Pt and Cu) have been synthesized using different techniques: (i) impregnation (ImR) route to achieve NPs in the size range of 10-50 nm; (ii) organometallic (OM) approach to synthesize uniform and ultrafine NPs in the size range of 1-5 nm (i.e., Fe NPs were synthesized through a novel synthesis route to attain 1-3 nm NPs); (iii) Nanowire (NW) top-down approach to obtain ultrafine copper metal NPs in the size range of 2-3.8 nm. The enhancements in the fuel productivity were found to be 5-30 times higher for the smaller metal NPs over the larger metal NPs and moreover, with reduced metal loading from 10 to 1-2 wt %. A different set of electrodes based on nano-foams (Cu NF and Fe NF on Cu foil, Fe foil, Al foil, Inconel foil and Al grid/mesh) prepared via electro-deposition were also investigated, to further improve CO2 to fuels conversion. After, optimization of deposition and voltage using cyclic voltammetry, the fuels improved by 2-10 times over the highest net fuels achieved using metal NPs doped CNT electrodes

Ce travail de thèse porte sur l’étude des propriétés optiques de nanofils InP et d’hétérostructures nanofils InAs/InP épitaxiés sur substrat silicium. Ce travail de thèse a été réalisé principalement dans le cadre du projet ANR «INSCOOP». / This thesis is focused upon the experimental investigation of optical properties of InAs/InP NW heterostructures by means of photoluminescence (PL) spectroscopy. First, it was demonstrated that the host-substrate may have significant impacts on the optical properties of pure InP NWs, as due to the strain, created by the difference in the LTECs of the NWs and the host-substrate, as due to some other surface effects. Next, the optical properties of such nanowire heterostructures as quantum rod (QRod) and radial quantum well (QWell) NWs were investigated. The features of obtained spectra were explained using theoretical simulation of similar NW heterostructures. The polarization properties of single InP NWs, InAs/InP QWell-NWs, InAs/InP QRod-NWs and ensemble of the InAs well ordered NWs were studied at different temperatures. Further, we report on the evidences of the strain-induced piezoelectric field in WZ InAs/InP QRod-NWs. Finally, PL QE of NW heterostructures and their planar analogues are measured by means of a PL setup coupled to an integrating sphere. In general, the obtained knowledge of the optical and mechanical properties of pure InP NWs and InAs/InP NW heterostructures will improve understanding of the electrical and mechanical processes taking place in semiconductor NW heterostructures and will serve for the fabrication of future nanodevice applications.

In this thesis I present a study of nanowires, and, in particular, I apply EBIC microscopy for investigation of their electro-optical properties. First, I describe details of the EBIC analytical technique together with a brief historical overview of the electron microscopy, the physical principles of the EBIC, its space resolution, parameters defining the signal amplitude, and the information we can acquire concerning defects, electric fields, etc. Then I focus on the characterization of LEDs based on GaN nanowires, which were analyzed in a cross-section and in a top view configurations. The EBIC measurements were correlated with micro-electroluminescence mapping. Further, I address the fabrication and measurement of nanowire-based InGaN/GaN LEDs detached from their original substrate. I present the EBIC measurements of individual nanowires either cut from their substrate and contacted in a planar geometry or kept standing on supphire substrate and cleaved to reveal the horizontal cross-section.The next part of this thesis is dedicated to an EBIC study of irregular Si nanowire array-based solar cells, and then of the regular nanowire array devices. The current generation was analyzed on a submicrometer scale. Finally, I discuss the fabrication and EBIC measurements of GaN nanowires grown on Si substrate. In particular, I show that the p-n junction was induced in the Si substrate by Al atom diffusion during the nanowire growth. / Dans cette thèse je me propose d’étudier des nano-fils, et en particulier d’utiliser la technique EBIC pour explorer leurs propriétés électro-optiques. Je décris d’abord les détails de la technique d’analyse EBIC avec un bref retour historique sur la microscopie électronique, le principe physique de l’EBIC, sa résolution spatiale, les paramètres conditionnant l’amplitude du signal, et les informations que l’on peut en tirer sur le matériau en termes de défauts, champ électrique, etc. Je m’intéresse ensuite à la caractérisation de LEDs à nano-fils à base de GaN, qui ont été observés par EBIC, soit en coupe soit en vue plane (depuis le haut des fils). Les mesures EBIC sont comparées à celles de micro-électroluminescence. Plus loin j’adresse la fabrication et la mesure de nano-fils à base de GaN séparés de leur substrat d’origine. Je présente les mesures EBIC de nano-fils uniques entiers, puis de nano-fils en coupe horizontale.La partie suivante de la thèse traite d’étude EBIC des cellules solaires à base de nano-fils Si ayant d’abord une géométrie aléatoire, puis une géométrie régulière. La génération de courant dans ces cellules solaires est analysée à l’échelle submicronique. A la fin du manuscrit je discute la fabrication et les mesures EBIC de fils GaN épitaxiés sur Si. Je montre en particulier qu’une jonction p-n est enduite dans le substrat Si par la diffusion d’Al lors de la croissance de nanofils.