Experimental thermal-hydraulic study of a rectangular supercritical CO2 natural-circulation loop with a horizontal heated channel was conducted at different steady-state conditions. These included different system pressures and three different inlet temperatures, with different inlet and outlet valve openings. Approximately, 450 experimental steady-state data-points were collected. The data include measurements of pressure-drop along the heated channel, pressure-drop across inlet and outlet valves, applied heat on the heated channel, pressure, temperature and flow-rate. Steady-state curves of mass flow-rate versus power, outlet temperature versus power, and detailed information of frictional pressure drop and local head loss coefficients were produced. Comparison showed that for the available experimental set-up, computed frictional pressure-drops fell within 1-1.20 of the Blasius formula prediction. Moreover, flow oscillations were observed in several cases when outlet temperature of CO2 was higher than the pseudo-critical temperature on the negative slope part of the mass flow-rate versus power curve.

The removal of heat from the containment building is an important consideration in the design of a nuclear power plant. In this investigation a simple rectangular natural circulation loop was simulated to determine whether it could possibly be used to remove usable quantities of heat from a containment building. The loop had a vertical pipe on the inside and outside of the containment building. These pipes acted as heat exchangers. Single phase and two phase cases were simulated by imposing a temperature on the respective vertical leg pipe walls and determining the heat absorption from the containment building. The heat was conveyed from the inside of the building to the outside via the natural circulation phenomenon. A literature study was done to cover topics relevant to this investigation. A theoretical model using conservation equations and control volumes was derived. This model was based largely on knowledge gleaned from the literature study. The theoretical model was a simple homogenous model, which was sufficiently detailed for a conceptual investigation. The theoretical model was then manipulated into a form suitable for use in a computer simulation program. Simplifications were made to the simulation model and underlying theory due to the nature of the investigation. The simulation model was validated against published experimental results. During the simulation phase a number of cases were investigated. These cases were divided into base cases and parametric studies. During the base case simulations the change of key fluid variables along the loop was examined. During the parametric studies the hot and cold leg inside wall temperatures, loop geometry and pipe diameter were varied. The effect of these parameters on the heat absorption from the containment was determined. The simulations showed that with the current assumptions about 75 to 120 of the natural circulation loops are needed depending on their geometry and containment conditions. The heat removal rates that were calculated varied from 50 kW to 600 kW for a single loop. As explained in the final chapter, there are many factors that influence the results obtained. The natural circulation concept was deemed to be able to remove usable quantities of heat from the containment building. / Thesis (M.Ing. (Nuclear Engineering))--North-West University, Potchefstroom Campus, 2012.

The removal of heat from the containment building is an important consideration in the design of a nuclear power plant. In this investigation a simple rectangular natural circulation loop was simulated to determine whether it could possibly be used to remove usable quantities of heat from a containment building. The loop had a vertical pipe on the inside and outside of the containment building. These pipes acted as heat exchangers. Single phase and two phase cases were simulated by imposing a temperature on the respective vertical leg pipe walls and determining the heat absorption from the containment building. The heat was conveyed from the inside of the building to the outside via the natural circulation phenomenon. A literature study was done to cover topics relevant to this investigation. A theoretical model using conservation equations and control volumes was derived. This model was based largely on knowledge gleaned from the literature study. The theoretical model was a simple homogenous model, which was sufficiently detailed for a conceptual investigation. The theoretical model was then manipulated into a form suitable for use in a computer simulation program. Simplifications were made to the simulation model and underlying theory due to the nature of the investigation. The simulation model was validated against published experimental results. During the simulation phase a number of cases were investigated. These cases were divided into base cases and parametric studies. During the base case simulations the change of key fluid variables along the loop was examined. During the parametric studies the hot and cold leg inside wall temperatures, loop geometry and pipe diameter were varied. The effect of these parameters on the heat absorption from the containment was determined. The simulations showed that with the current assumptions about 75 to 120 of the natural circulation loops are needed depending on their geometry and containment conditions. The heat removal rates that were calculated varied from 50 kW to 600 kW for a single loop. As explained in the final chapter, there are many factors that influence the results obtained. The natural circulation concept was deemed to be able to remove usable quantities of heat from the containment building. / Thesis (M.Ing. (Nuclear Engineering))--North-West University, Potchefstroom Campus, 2012.