Spelling suggestions: "subject:"benjet"" "subject:"aspectjet""
1 |
Wall Features of Wing-Body Junctions: Towards Noise ReductionOwens, David Elliot 16 August 2013 (has links)
Much research and experiments have gone into studying idealized wing-body junction flows and their impact on horseshoe vortex and wake formation. The vortices have been found to generate regions of high surface pressure fluctuations and turbulence that are detrimental to structural components and acoustics. With the focus in the military and commercial industry on reducing the acoustical impact of aircraft and their engines, very little research has been done to examine the potential impact wing-body junctions may have on acoustics, especially for high lifting bodies such as propellers. Two similar tests were conducted in the Virginia Tech Open Jet Wind Tunnel where boundary layer measurements, oil flow visualizations, acoustic linear array and surface pressure fluctuation measurements of a baseline Rood airfoil model and two novel junction fairing designs were all taken. Boundary layer measurements were taken at four locations along the front half of the flat plate and the profiles were shown to be all turbulent despite the low Reynolds number of the flow, (test 1: Re_"<1400, test 2: Re_"<550). Oil flow visualizations were taken and compared to those of previous researchers and the location of separation and line of low shear along with the maximum width of the wake and width of wake at the trailing edge all scaled relatively well with the Momentum Deficit Factor, defined for wing-body junction flows [Fleming, J. L., Simpson, R. L., Cowling, J. E. & Devenport, W. J., 1993. An Experimental Study of a Turbulent Wing-Body Junction and Wake Flow. Experiments in Fluids, Volume 14, pp. 366-378. ]. A linear microphone array was used to estimate the directivity of the facility acoustic background noise to be used to improve background subtraction methods for surface pressure fluctuation measurements. Surface pressure fluctuation spectra were taken ahead of the leading edge of the plate and along the surface of the models. These showed that the fairings reduced pressure fluctuations along the plate upstream of the leading edge, with fairing 1 reducing them to clean tunnel flow levels. On the surface of the models, the fairings tended to reduce low frequency (<1000Hz) pressure fluctuation peaks when compared to the baseline model and increase the pressure fluctuations in the high frequency range. Simple scaling arguments indicate that this spectral change may be more beneficial than detrimental as low frequency acoustics especially those between 800 Hz and 1200 Hz are the frequencies that humans perceive as the loudest noise levels. Scaling the frequencies measured to those of full scale applications using Strouhal numbers show that frequencies below 1000 Hz in this experiment result in frequencies at the upper limit of the human hearing frequency range. Low frequency acoustic waves also tend to travel farther and high frequency acoustic waves are more apt to be absorbed by the surrounding atmosphere. / Master of Science
|
2 |
Characterization of Upstream Effects Due to High Blockage in the AFRL Vertical Wind TunnelSholtis, Paul M. 30 May 2019 (has links)
No description available.
|
3 |
Measurement and Prediction of Rotor Noise Sources for sUAS in Outdoor and Laboratory EnvironmentsWhelchel, Jeremiah Mark 30 August 2023 (has links)
This work provides an experimental analysis of the acoustic footprint of a hexacopter in hover and low speed forward flight, comparison of aerodynamic performance and noise of eVTOL rotors operating in multiple facilities, and analysis of the noise associated with an outrunner brushless DC motor. Empirical and low-order models are used to predict aerodynamic performance, tonal noise, and broadband noise for isolated eVTOL rotors. In addition, a low noise, swept rotor design was evaluated. The acoustic footprint of a DJI Matrice 600 Pro hexacopter in hover and low speed forward flight was measured in the Virginia Tech Drone Park. The noise radiated by this vehicle was found to be dominated by tonal noise at low frequencies and dominated by broadband noise at high frequencies indicating that both are important when assessing the noise of these aircraft. Three distinct regions were observed in the frequency spectra of the noise. A-weighting measured acoustic spectra highlighted the importance of the mid-frequency broadband noise, in particular. The radiated noise in hover was also found to be similar to the noise of the vehicle during low-speed flyovers. Given this, significantly less complex measurements of an aircraft in hover or those associated with a rotor at static conditions may be used to assess the footprint of an eVTOL aircraft in low speed forward flight. The total vehicle noise was then decomposed by studying the performance and noise of isolated eVTOL rotors in multiple facilities and under different operating conditions.
Facility effects on performance and noise were first assessed by experimentally studying two commercially available eVTOL rotors in an enclosed anechoic environment and an open environment. For experimental measurements that were conducted in the anechoic chamber, recirculation effects were shown to increase harmonic amplitudes more than 8 dB. Varying solidity screens were placed in the downstream wake of each rotor to delay the onset of recirculation. Placing the screens in the wake did not produce a noticeable effect on or delay recirculation within the confined testing environment. Measurements of the BPF and higher order harmonics of each rotor were found to be much more consistent in time when testing outdoors in an open-air environment. Amplitudes of these tones were also found to be like that of the spectral levels of the measurements conducted in the anechoic chamber once recirculation had been established. While the tonal levels were much more consistent throughout each measurement in the open-air environment, a significant amount of background noise was present and made characterizing the noise at low frequencies difficult. Environmental factors, mainly windspeed, were also found to impact the noise measurements which also added difficulty in characterizing the noise of the two tested rotors. In indoor facilities, the rotor inflow becomes contaminated due to recirculation shortly after the rotor reaches steady state and spectral levels of tones increased with increasing spectral averaging times. In outdoor environments, the inflow to the rotor disc becomes distorted due to changing wind conditions and turbulence in the atmosphere. Spectral levels of tones in the outdoor environment remained consistent in amplitude but exceeded those of the anechoic chamber significantly. Given this, environmental factors and recirculation were found to both increase the higher order harmonics.
To mitigate these facility effects, measurements of force and noise were also conducted for the same two rotors in an anechoic open jet. Additionally, measurements were also conducted for a commercially available rotor along with a newly designed low noise swept rotor. Each of these rotors were tested in the anechoic open jet facility at static conditions and with the tunnel on. These measurements were accompanied with predictions of aerodynamic performance and tonal and broadband self-noise. BEMT was used to predict aerodynamic performance. Tonal noise associated with the rotor blade loading and thickness was predicted using F1A and rotor broadband self-noise was predicted using the model of BPM. The measured noise in this facility along with that from measurements in the anechoic chamber and outdoor environment were separated into tonal and broadband components by applying a phase averaging technique to the measured acoustic pressure time history. These results also show that in the indoor facility that the noise produced at the BPF is dominated by tonal sources, but the higher order harmonics can be attributed to broadband interactions particularly at static conditions. Broadband noise was drastically reduced by driving the tunnel at minimal inflow for the smallest rotor studied (R_tip= 120 mm). For the larger rotors (R_tip≥ 267 mm) broadband noise associated with BWI or TIN were not mitigated at low inflow speeds. Predictions of tonal noise at the BPF were within 3 dB for all observer locations when considering the smallest rotor studied. Predictions of the measured directivity at the BPF for the larger rotors were inaccurate although predictions of thrust agreed with the measured. The largest rotors tested were equal in diameter to that of the open jet inlet. Thus, the limits of the testing facility were exceeded and increased noise was produced as the rotor blades interacted with the shear layer of the open jet. Directivity patterns of each rotor were also found to vary with increasing rotational rate. Overall, these results show that for analyzing the noise at hover conditions, introducing a small amount of inflow may be a good option when trying to understand the tonal noise and allows one to characterize the tonal noise independent of the broadband. However, this was also shown to be heavily dependent on the rotor diameter with regards to the open jet inlet and experimentalist must take this into consideration. While these measurements provide an analysis of the noise in hover and low speed ascent, they do not assess the noise of the vehicle operating in forward flight. In forward flight the rotors are subjected to edgewise flows which have an effect on the radiated noise thus analyzing the noise of these rotors operating at an angle of attack to the incoming flow was assessed.
These effects were investigated by experimentally measuring the performance and noise of the smallest rotor studied when operating at a yaw relative to the incoming flow. For increasing yaw at the examined wind tunnel velocities, the measured thrust was found to converge to the value for zero inflow. Contours of SPL as a function of yaw angle for no inflow and an inflow speed of 8 m/s showed spectral levels to be minimal for an in-plane observer from 5×BPF to 30×BPF. The broadband noise was found to increase significantly for increasing yaw angle and tunnel inflow speed. These results show once again that the broadband noise is especially important during forward flight and new methods that consider wake interaction are needed to predict the noise in this flight regime.
The rotor geometric parameter of sweep was also assessed from measurements in the anechoic open jet by comparing the aerodynamic performance and noise of a commercially available 762 mm diameter CF30x10.5 T-motor eVTOL rotor to that of an in house designed low noise swept rotor. The addition of sweep was found to reduce noise associated with BWI or TIN as the separated broadband noise was found to be less than that of the commercially available rotor. Comparison of thrust at static conditions and with increasing advance ratios showed both rotors to have similar performance, thus the addition of sweep was effective at reducing noise without sacrificing performance.
Lastly, the noise associated with the electric drive system of these aircraft which consists of an ESC and brushless DC motor was analyzed. Acoustic measurements were made with and without an acoustic enclosure installed on a brushless DC motor and was found to be effective at reducing noise associated with the electric motor. The effects of two ESC's as well as their switching rates were also studied. The noise was found to be similar for both ESCs at low frequencies. At high frequencies the measured noise spectrum was found to be different when controlling the motor with different ESC's and a higher switching rate was found to reduce the noise with increasing switching rate although not completely monotonically. / Doctor of Philosophy / A new class of multi-rotor VTOL electric aircraft is becoming a dominant advanced vehicle concept. Urban Air Mobility (UAM) vehicles are designed for short routes within urban environments carrying only a few passengers during each flight. Other smaller Unmanned Aerial Systems (UAS) are increasingly being used for delivery services or to perform tasks which are more easily accessed with this technology like inspection or photography. Thus, these vehicles are expected to operate in close proximity to the general populace exposing it to aircraft noise which is currently limited to communities surrounding airports. For successful integration into the airspace with minimal community annoyance, the mechanisms responsible for generation of the noise must be understood. Traditionally, for conventional rotorcraft (one main rotor), the tonal noise has been more of a concern than the broadband component. eVTOL vehicles are often equipped with multiple rotors that are lightly loaded and operate at lower tip speeds which can be time varying. Thus, there is an increased significance of broadband noise. Lastly, these aircraft are equipped with an electric drive system that gives rise to an additional noise source that is not present for conventional aircraft. Best practices for measuring eVTOL noise are not currently established. Measurement of eVTOL rotor noise is complicated by the increased significance of the broadband sources. These have been shown to be facility dependent. Given this, there is a need for high quality experimental data and an analysis of experimental data in multiple facilities for these rotors and drive systems. Capabilities of traditional models to predict conventional rotorcraft noise also need to be assessed for these rotors. These two issues have been assessed in this work by first assessing the character of an eVTOL aircraft in hover and low speed flyovers. Both tonal and broadband components of the radiated noise were found to be significant. A-weighting, which is a metric used to assess the response of the human ear to the radiated noise showed increased significance of the broadband noise. This was followed by a characterization of the noise of isolated eVTOL rotors in multiple environments. Facility effects were addressed, and a low order prediction model was developed using methods that are traditionally used to predict noise associated with conventional rotorcraft. Lastly, the noise associated with the electric drive system of these vehicles was assessed and recommendations on how to reduce this source of noise were made. These results can be used to guide experimentalists when performing measurements of eVTOL rotor noise at static conditions and provide an eVTOL rotor noise data set that can be used to validate existing and forthcoming aerodynamic and acoustic prediction methods.
|
4 |
Investigation of fluid-dynamic cavity oscillations and the effects of flow angle in an automotive context using an open-jet wind tunnel.Milbank, Juliette, milbank@turbulenflow.com.au January 2005 (has links)
Aeroacoustic whistles are a significant source of customer complaints to automotive manufacturers. Whistles can occur on many such components, but the relative position and configuration of rearview mirrors means they are a more problematic source of tonal noise on vehicles. The low subsonic complex turbulent flow, combined with small cavity scales, determines the possible whistle mechanisms. The one considered to be most problematic, fluid-dynamic cavity resonance, is the topic of this research thesis. The research scope is limited to the automotive environment of external rearview mirrors and the fluid-dynamic resonance mechanism: low subsonic Mach number, M = 0.05 - 0.13; laminar boundary layers; and two-dimensional, acoustically compact cavities. The low unit-cost of rearview mirrors and the desire to have simple identification and prediction schemes, that could be used by production engineers, determined an empirical approach. A search of the existing literature revealed that there were some data on cavities of the above scale in low Mach number flow, but quoted errors in empirical descriptions were large and there was very little research on the effects of flow yaw angle on the chosen resonance mechanism. The research therefore aims to determine whether existing empirical descriptions of fluid-dynamic cavity resonance are suitable for the prediction of the resonance characteristics, with sufficient accuracy to enable unambiguous identification of the presence of the resonance and its mechanism. A second aim is to investigate the effects of a feature of the automotive flow environment, flow yaw angle, on the resonance. Flow yaw angle is determined by those components of the flow in the same plane as the surface in which the cavity is situated. An experimental program was undertaken using a purpose-built aeroacoustic wind tunnel and a simple cavity model. Testing with two types of cavity configurations, as well as flow visualisation, investigated the main features of the resonance in time-averaged yawed flow. Within the scope of this thesis, it is shown that fluid-dynamic cavity resonance characteristics can be accurately identified by a simple empirical model, even in yawed flow. Various descriptors allow identification of the resonance threshold, stage, frequency and relative amplitude in non-yawed flow, while the frequency and stage can also be identified in yawed flow. The relative decrease in resonance amplitude in yawed flow, although identified for these experiments, would depend on the degree of spanwise variation in the boundary layer characteristics for a given cavity configuration. The results also identify significant issues with testing in a free jet tunnel, due to the nature of fluid-dynamic cavity resonance and the fluctuation energy content in free shear layers. Despite this, the thesis aims are achieved, and appropriate design guidelines are produced for automotive designers.
|
5 |
Etude numérique de la diffusion d'une onde acoustique par une couche de cisaillement turbulente à l'aide d'une simulation aux grandes échelles / Study of the scattering of an acoustic wave by a turbulent shear layer using large-eddy simulationBennaceur, Iannis 30 June 2017 (has links)
Lors des mesures acoustiques dans les souffleries à veine ouverte, les ondes acoustiques émises par une maquette ou une source située dans la veine se propagent dans la couche de cisaillement turbulente qui se forme aux abords du jet avant d’être reçues par les microphones localisés en dehors. L’onde acoustique interagit avec le champ de vitesse turbulent de la couche de mélange ce qui a pour effet de modifier son contenu spectral, de redistribuer spatialement son énergie et de moduler sa phase et son amplitude, on parle alors de diffusion acoustique. Cette thèse a consisté à l’étude de la diffusion d’une onde acoustique par une couche de cisaillement turbulente à l’aide d’une simulation numérique aux grandes échelles. Pour cela, il a d’abord été nécessaire de réaliser la simulation numérique aux grandes échelles d’une couche de cisaillement turbulente plane dans son régime auto-similaire. Dans un second temps, nous avons simulé l’interaction entre une onde acoustique et l’écoulement turbulent afin d’étudier les caractéristiques du champ de pression diffusé qui en résulte. Nous avons notamment vérifié que la simulation était capable de prédire précisément les fréquences sur lesquelles est répartie la plupart de l’énergie acoustique ainsi que la forme du spectre de pression diffusé. Finalement, le champ de vitesse du milieu turbulent qui est corrélé avec l’enveloppe du champ de pression diffusé a été reconstruit à l’aide de la méthode de l’estimation stochastique linéaire. Cette méthode nous a notamment permis de visualiser les larges structures turbulentes qui interviennent principalement dans le mécanisme de diffusion acoustique. / During open jet wind tunnel measurements, the acoustic waves emitted by a device or an acoustic source located inside the flow propagate inside the turbulent shear layer that develops at the periphery of the jet before being received by microphones located outside the flow. The acoustic wave interacts with the turbulent velocity field leading to a change of directivity, a phase and amplitude modulation as well as a spectral re-distribution of the acoustic energy over a band of frequencies. This phenomenon is known as acoustic scattering. This work has consisted in the study of the scattering of an acoustic wave by a turbulent shear layer using large-eddy simulation. The first step of the study has consisted in the large-eddy simulation of a turbulent shear layer in its self-similar state. In a second second step, the direct computation of the interaction between the acoustic wave and the turbulent flow has been performed in order to study the characteristics of the resulting scattered pressure field. It has been shown that the numerical simulation is able to accurately predict the frequencies on which the main part of the scattered energy is redistributed, as well as the shape of the scattered pressure spectrum. Finally, the turbulent velocity field which is correlated with the envelope of the scattered pressure field is reconstructed using the linear stochastic estimation method. This method has enabled the visualization of the large turbulent structures that mainly take part in the acoustic scattering mechanism.
|
Page generated in 0.0275 seconds