Along with the rapidly increasing demand for wireless data while more and more crowded radio frequency (RF) spectrum, optical wireless communications (OWC) become a promising candidate to complement conventional RF communications, especially for indoor short and medium range data transmissions. Orthogonal frequency division multiplexing (OFDM) is considered for OWC due to its ability to boost data rates. However, the average emitted optical power and dynamic range of driving signals of LEDs are two major constraints in OWC. OFDM waveforms exhibits high upper and lower peak-to-average power ratios (PAPRs), which make OFDM signals optical power inefficient and easy to violate the dynamic range of LEDs, resulting clipping and nonlinear distortions. In this dissertation, we analyze and design optical power and dynamic range constrained OWC systems, for which OFDM is our major subject. We first derive distributions of upper PAPR and lower PAPR of OWC-OFDM signals. Then we analyze the clipped OFDM signals in term of error vector magnitude (EVM), signal-to-distortion ratio (SDR), and achievable data rates under both optical power and dynamic range constraints. The next part of this dissertation is the OFDM system design for visible light communications (VLC) considering illumination requirement. We investigate the illumination-to-communication efficiency (ICE) in VLC-OFDM, and design the brightness control and flickering mitigation schemes for VLC-OFDM. In the end, to reduce the complexity of driving circuits of LEDs , we propose using delta-sigma modulators in VLC-OFDM systems to convert continuous magnitude OFDM symbols into two-level LED driver signals without loss of the communication theory advantages of OFDM.

This master's thesis deals with the analysis of the optical power measurement using an optical fiber sensor. The thesis contains the theoretical background to understand the origin of polarization and its representation in space using Poincaré’s sphere and Stokes vectors. There is also a part describing optical performance measurement and the preview of analog measurements from various researches. Practical part focuses on verification of changes of fiber sensor parameters at temperature change in its surroundings and this part includes also additional suggestions for various types of measurements and verification of the function of the photodiode as an optical power transducer. Most measurements are based on the comparison of results obtained with the polarimeter. The results were plotted and discussed.

The topic of this master’s thesis is energy measurement of the optical intensity distribu-tion at the far field. Properties of the optical intensity and the optical power are described. In this thesis solution of wave equation is done. The plane wave, spherical wave and Gaussian beam are described. In this thesis, optical trace of laser beam from transmitter laser diode to receiver PIN photodiode is described. One of the solved problems is diffraction on the lens socket. The basic configuration for diffraction investigation on lens socket was created. There were transmitting laser diode, stop with circular apertures and PIN photodiode used in the experiment. In the other part, thesis deals with measuring and detection of the optical beam. Sorts of photodiodes and their characteristics were analysed.

Les réseaux optiques dynamiques et flexibles font partie des scénarios d'évolution des réseaux de transport optique. Ceux-ci formeront la base de la nouvelle génération des réseaux optiques de demain et permettront le déploiement efficace des services tel que le Cloud Computing. Cette évolution est destinée à apporter flexibilité et automatisation à la couche optique, mais s'accompagne d'une complexité supplémentaire, notamment au niveau de la gestion et de la commande de cette toute nouvelle génération de réseau. Jusqu'à récemment, les protocoles de routage et de signalisation normalisés ont pris en compte plusieurs paramètres physiques tels que l'information spectrale de la bande passante, le format de modulation, et la régénération optique. Cependant, d'autres paramètres sont encore nécessaires (par exemple, les puissances optiques des liens, le gain des amplificateurs) afin de faire fonctionner efficacement de grands réseaux. Dans ce contexte, il y a un besoin d'étudier les réseaux optiques existants ainsi que les différentes méthodes de prise en compte de la couche photonique dans le plan de contrôle. Le but est d'avoir un réseau optique automatique, flexible et programmable, mais surtout efficace de point de vue économique et opérationnel. L'utilisation de la technologie à grille flexible a un impact sur les réseaux optiques existants, où presque tous les équipements devront être remplacés, ce qui entraînera un coût additionnel pour les opérateurs. Dans ce travail, nous étudions les réseaux optiques actuels et évaluons l'impact de la flexibilité sur les infrastructures existantes. Ensuite, nous identifions plusieurs paramètres optiques à contrôler et proposons des extensions protocolaires afin d'intégrer ces paramètres dans un plan de contrôle GMPLS. De plus, nous développons les algorithmes de routage et de signalisation qui permettent la mise en œuvre d'un plan de contrôle efficace qui répond au besoin de la flexibilité. Enfin, l'ensemble de nos propositions et de nos solutions sont évaluées sur plusieurs topologies réseaux avec des modèles de trafic différents dans le but de valider leur pertinence. / Dynamic and flexible optical networks are among the evolution scenarios of the optical transport networks. These form the basis of the new generation of optical networks of tomorrow and enable the effective deployment of services such as cloud computing. This evolution is intended to provide flexibility and automation to the optical layer. However, it results in additional complexity, particularly in terms of the management and control of this new network generation. Until recently, the standardized routing and signaling protocols have been taking into account several optical parameters like the spectral bandwidth information, modulation format, and optical regeneration. However, other parameters (e.g., link optical powers, gain of optical amplifiers) are still required in order to efficiently operate large optical networks. In this context, there is a need to study the existing optical networks and the different integration methods of the photonic layer in a control plane. The goal is to get an automatic optical network that is flexible, programmable, and at the same time efficient from an economical and operational perspective. The use of flexible grid technology has an impact on existing optical networks, where almost all the equipment must be replaced, resulting in an additional cost to network operators. In this work, we study the current optical networks and evaluate the impact of flexibility on the existing infrastructures. Then, we identify several physical parameters to be controlled and propose protocol extensions in order to integrate these parameters in the GMPLS control plane. In addition, we develop the routing and signaling algorithms that allow the implementation of an efficient control plane that addresses the need for flexibility. Finally, the set of our proposals and solutions are evaluated on multiple network topologies with different traffic patterns in order to validate their relevance.

Thesis describes shortly types of waves and beams. Gaussian beam properties and parameters are described in more details, Gaussian beam is the most used in atmospheric optical links. The main goal of work is studying of possibilities of laser beam shaping, mainly the beam Top hat. In this project reasons why is suitable to shape laser beam for optical communications and the most used methods for shaping of laser beam are described. The suggested processes of beams shaping are experimentally verified and properties of beams shaped of single methods are compared with each other.