M.Ing. / The aim of this project is to research the feasibility of an all-fibre laser distance measurement device that utilises a figure-eight fibre laser (F8L), in the nonlinear amplifying loop mirror (NALM) configuration, as a light source and implements pulse compression to improve the accuracy and signal-to-noise ratio of the system. A figure-eight fibre laser in the NALM configuration for use in a laser distance measurement device is described. The theory of fibre lasers is discussed, including mode-locking and Qswitching, and the characteristics of a NALM loop are analysed. By varying the length of the NALM loop from 500 m to 2000 m or inserting highly nonlinear dispersion shifted fibre, a variety of pulses in the picosecond to nanosecond range can be produced. The lengths of the pulses depend on the length of the NALM loop, the pump power and the setting of the polarisation controllers. The figure-eight fibre laser is pumped with a 980 nm laser diode up to 550 mA, which corresponds to 320 mW. Distance measurements are done with short unmodulated and long modulated pulses. Distance measurement with short unmodulated pulses is discussed only briefly and tested with a simple experiment. The focus of this project is distance measurement with long modulated pulses. A low autocorrelated binary sequence is modulated onto one of the long pulses produced by the figure-eight fibre laser by an electro-optic amplitude modulator. The long pulse gives the proposed system a good signal-to-noise ratio (SNR), while the modulation improves the accuracy. A Barker code of length 13 is proposed as modulation code because of its good autocorrelation properties. The Barker code will improve the accuracy 13-fold, with a corresponding increase in SNR. An electro-optic amplitude modulator is used to implement the modulation. The modulated long pulse is then sent to a target. After reflection, the signal is detected and cross-correlated to obtain the time-of-flight for the pulse. The code generation and cross-correlation are implemented with an FPGA via VHDL programming. The distance to a target can be calculated by knowing the time-of-flight and the speed of light in the propagation medium. In this project the resolution, single-shot precision, accuracy, linearity, repeatability and maximum unambiguous distance of the proposed all-fibre laser distance measurement device are examined.

Optical fibre networks play an increasingly prominent role in communications. As networks grow in size and complexity, the probability and impact of failures increase. In this dissertation, different optical network concepts, survivability and resilience methods are considered. Link and Path failures are discussed and Static Path Protection (SPP), Shared Backup Path Protection (SBPP), as well as Path Restoration (PR) are investigated. A Shared Backup Path Protection model and simulation tool is designed and implemented. This implementation is compared with other studies. Dual-link failures are considered under specific network topologies. Shortest Path algorithms are used to reprovision optimal routes for backup protection. Results and conclusions are discussed in detail, giving valuable insight into resilience methods. Availability and protectability are discussed and evaluated as measures of resilience and network survivability. Results vary between compromising little availability and bringing a significant improvement in availability. It is concluded that the implementation of SBPP is a necessity in highly-meshed networks with high availability needs, but doesn’t necessarily provide the best solution for sparsely-connected networks. The additional cost involved in the implementation needs to be considered carefully. / Dissertation (MEng)--University of Pretoria, 2007. / Electrical, Electronic and Computer Engineering / unrestricted

Les verres de chalcogénures combinent plusieurs propriétés : une transparence étendue dans l’infrarouge, un indice de réfraction élevé (n>2) et de fortes propriétés non-linéaires. La réalisation de fibres optiques microstructurées (FOMs) permet d’exacerber les effets non-linéaires et notamment en faisant varier les paramètres optogéométriques des fibres (d et Λ). Ainsi, des fibres à propagation monomode peuvent être obtenues ou encore des fibres dont les applications potentielles concernent l’optique active avec la génération d’effets non-linéaires. La réalisation de telles fibres passent par la synthèse de verres de chalcogénures de haute pureté. Par conséquent, les bandes d’absorption limitant la transparence des fibres doivent être identifiées et limitées au maximum. Pour cela, le suivi et la qualification des éléments utilisés lors de la synthèse des verres doivent être entrepris. Un protocole de synthèse et de purification par traitements thermiques a été mis en place en ce sens. La technique pour élaborer les FOMs en verres de chalcogénures est le moulage. Elle consiste à couler un verre dans un moule entièrement réalisé en silice. Ce dernier présente la géométrie inverse de la fibre désirée. Cette méthode permet d’obtenir des géométries variées et reproductibles en passant par des fibres monomodes et multimodes avec des diamètres de cœur allant de 2 μm jusqu’à plus de 20 μm. La réalisation de sources infrarouges a été développée dans le manuscrit. Cela a été rendu possible dans un premier temps par la génération d’un supercontinuum à l’aide d’une fibre à cœur suspendu puis par la réalisation d’un laser à cascade quantique (QCL) couplé à une fibre monomode. De plus, une fibre à maintien de la polarisation (FMP) dans le moyen infrarouge, présentant une biréfringence de groupe de l’ordre de 10-3 a été élaborée grâce à l’évolution du moule de silice. De plus, un coupleur tout-optique, une fibre toute-solide et un faisceau de fibres infrarouges complètent les réalisations obtenues au cours de cette thèse. / Chalcogenide glasses combine several properties : large transparency in the infrared range, a high refractive index (n>2) and strong non-linear properties. The realization of microstructured optical fibers (MOFs) exacerbates non-linear effects more particularly by varying the opto-geometrical parameters of the fibers (d and Λ). Thus, single-mode propagation can be obtained and also generation of non-linear effects. The realization of high purity chalcogenide glasses is needed. In fact, absorption bands limiting the transparency of the fibers must be identified and minimized. For this, monitoring and qualification of components used in the synthesis of glasses should be undertaken. A protocol of synthesis and purification by heat treatment was implemented in this direction. The technique to elaborate MOFs is the casting method. It consists of flowing a glass on a silica mold. The geometry is the negative shape of the desired fiber. This method allows the realization of multimode or single-mode fiber in the 1-10 μm window. The realization of infrared sources was developed in the manuscript. The generation of a supercontinuum with a suspended-core fiber has been presented and also by the realization of a quantum cascade laser (QCL) coupled into a singlemode fiber. In addition, a polarization-maintaining fiber (PMF) having a group birefringence of the order of 10-3 was developed through the evolution of the silica mold. In addition, an optical coupler, an all-solid fiber and an infrared bundle were achieved during this thesis.

In this thesis, the work focuses on developing distributed optical fiber vibration sensors based on phase-sensitive optical time domain reflectometry (Φ-OTDR). Three works have been accomplished to improve the performances of Φ-OTDR for distributed vibration sensing. Firstly, Φ-OTDR based on a polarization diversity scheme is demonstrated to mitigate the polarization mismatch effect occurring in traditional systems. A theoretical analysis is performed in different polarization cases corresponding to coherent and polarization diversity detection. Φ-OTDR based polarization diversity shows a great potential in the multi-events sensing application. Two vibration events are simultaneously detected and their signal to noise ratios are improved by 10.9 dB and 8.65 dB, respectively, compared to the results obtained by a conventional coherent scheme. Intensity fluctuation in a phase-sensitive optical-time domain reflectometry (Φ-OTDR) system caused by stochastic characteristics of Rayleigh backscattering has limited relative vibration strength measurement, which is proportional to dynamic strain. A trace-to-trace correlation coefficient is thus proposed to quantify the Φ-OTDR system stability and a novel approach of measuring the dynamic strain induced by various driving voltages of lead zicronate titanate (PZT) is demonstrated. Piezoelectric vibration signals are evaluated through analyzing peak values of the fast Fourier transform spectra at fundamental frequency and high-order harmonics based on Bessel functions. Experimental results show high correlation coefficients and good stability of our Φ-OTDR system, as well as the small measurement uncertainty of measured peak values. To reduce the intra-band noise caused by the finite extinction ratio of optical pulses, Φ-OTDR based on high extinction ratio generation is studied. Two methods are developed for achieving high extinction ratio of optical pulse generation. One of the approaches is to synchronize two cascaded electro-optic modulators to achieve high extinction ratio operation. The other one is to use the nonlinear optical fiber loop mirror as an optical switch to suppress the continuous wave portion of optical pulse. The sensing range of 1.8 km and 8.4 km with corresponding spatial resolution of 0.5 m and 2 m have been demonstrated based on cascaded two electro-optic modulators and nonlinear optical fiber loop mirror setup, respectively.

Optical fiber sensors have been intensively studied and successfully employed in various human social activities and daily living, such as industrial production, civil engineering, medicine, transportation, national defense and so on. According to different structures, optical sensors could be divided into various categories. This thesis focuses on studying different kinds of in-line fiber Mach-Zehnder interferometers, which have played an important role among the optical interferometric fiber sensors. The structure composition, fabrication process, physical principle and practical applications of two novel in-line fiber Mach-Zehnder interferometers are proposed and discussed in detail in this work. The tapered bend-insensitive fiber Mach-Zehnder interferometer (BIF-MZI) is firstly fabricated and used as a fiber vibrometer. The unique double-cladding structure of bend-insensitive fiber not only provides higher mechanical strength to the sensor, but also guarantees a more uniform transmission spectrum， since only a few inner-cladding modes are left interfering with the core mode. A high sensitivity and fast response intensity demodulation scheme is employed by monitoring the power fluctuation of the BIF-MZI at the operation wavelength. Both damped and continuous vibrations are detected using the proposed sensor. It is demonstrated that this sensor responses to an extremely wide range of frequencies from 1 Hz up to 500 kHz with high signal-to-noise ratios (SNRs). The discrimination of temperature and axial strain is realized based on the dispersion effects of high-order-mode fiber (HOMF) by forming a single mode fiber-high-order-mode fiber-single mode fiber (SMF-HOMF-SMF) structure based in-line Mach-Zehnder interferometer. Unlike some kinds of in-line MZIs such as tapered and core–offset structures whose cladding modes are excited with different types under changing temperature and strain circumstances, the HOMF is capable of supporting three stable core modes, which guarantees a reliable and repeatable measurements within a large temperature or strain range. A new method based on the fast Fourier transform (FFT) is employed to analyze the mode couplings and their chromatic dispersion and intermodal dispersion properties in HOMF. The strong dispersion effects lead to a multi-peak feature in the spatial frequency spectrum. It is found that peaks that denote the waveform periods at positions that are beyond the critical wavelength possess highly sensitive and distinct phase responses to external disturbances, which provides the possibility to realize the discrimination measurements with high sensitivities and smaller errors by selecting appropriate peaks. The phase demodulation scheme is applied to quantify the temperature and strain changes in terms of phase shifts. Appropriate peak selections according to the practical needs would provide an easy access for applications where more than two parameters are required to be discriminated.

The diploma thesis deals with the combined use of SEM and SPM techniques using optical fiber, which is used to collect the cathodoluminescent signal in close proximity to the sample. The thesis also includes a research section, which lists description of CPEM technique, the techniques used to modify the optical fiber, theoretical introduction to cathodoluminescence and techniques used to measure it. The practical part discusses the obtained measurement results and the problems that occurred in the process of modification of the optical fiber, its use as an SPM probe and in the measurement of cathodoluminescence active materials.

The main goal of the diploma thesis is DWDM simulation of optical network, defined by recommandation ITU-T. Optical network includes 16 communication channels with length of fiber 50 km. Each channel have to be set with bandwith 50GHz and Bit rate with minimal value 10Gbit/s. The final simulation model includes 8 types of modulation techniques. The result of the thesis is comparison modulation techniques in terms of usability of bandwith and comparison of the quality of transfer

Oceans cover 71% Oceans cover 71% surface of the earth and are rich in oil and gas resources, marine living resources, renewable energy, mineral resources. The depths of the oceans are often thought of as a silent world, but that was never the case, and oceans have become noisier as human technologies have advanced. Humans have not only added noise to the ocean; they have also eliminated natural sounds. One of the primary noise sources is sonar. Sonar technology is widely used in fish detection, ocean floor mapping, and vehicle navigation. The noise in the ocean dramatically affects the animal’s survival and breaks marine ecological balance. Herein, underwater wireless optical communication (UWOC) and fiber communication and sensing (FC&S) technologies are proposed to minimize the acoustic noise in the ocean. Compared to noisy, powerful acoustic communication technology, UWOC has the merit of silence and takes advantage of high bandwidth, high transmission speed, and power efficiency. Multi-functions FC&S system turns the submarine telecommunication cable network into sensor network. UWOC and underwater FC&S technology can boost the development of Underwater Internet of things (UIoT) by establish large-scale underwater sensor networks. This dissertation aims to investigate and address noisy ocean issues and build large-scale underwater sensor networks by optical communication and sensing technology. The dissertation proposes using UWOC and FC&S technology to replace the conventional acoustic communication technology and reduce the noise in the ocean. UWOC helps achieve high-speed wireless communications between sensors, vehicles, and even humans for UIoT. The significant challenges of developing UWOC systems are the complex underwater environment's attenuation, scattering, and turbulence effects. This dissertation studied the turbulence effects on the UWOC system’s performance and addressed the pointing-acquisition-and-tracking issues. The diffuse-line-of-sight configuration and scintillating-fiber-based detector help the mobile UWOC systems relieve the strict requirements on PAT. FC&S technology is proposed to build underwater communication and sensor networks. Studies pave the way for UIoT and keep ocean silent. Such modality is much sought-after for implementing robust UWOC links in a complex oceanic environment, building large-scale sensor networks across the oceans, and minimizing noise pollution in the ocean.

Corrosion related deterioration of aging aircraft has proven to cause reduced flight availability, service lifetime, costly repairs, and if undetected, can result in potentially unsafe operating conditions. The purpose of this research is to develop, fabricate and test optical fiber-based chemical sensors for monitoring corrosion from early stages through the entire corrosion event. Although there are several preventative methods under development to address the problem of corrosion degradation, new techniques are still needed that are cost-effective and reliable to ensure an acceptable health status determination of aging aircraft and civil infrastructure. In using optical fiber-based sensors to detect corrosion precursors such as moisture, pH, nitrates, sulfates, chlorates and corrosion related metal-ion by-products the severity of the corrosive environment can be determined allowing predictive health evaluation of the infrastructure. The long period grating (LPG) element is highly sensitive to refractive index changes and with appropriate design geometry a variety of target molecules can be detected. Optical fiber long period gratings are designed to act as spectral loss elements that couple a discrete wavelength out of the optical fiber as a function of the surrounding refractive index. By applying special coating that change refractive index with absorption of target molecules to the LPG surface, it becomes a transducer for chemical measurement. Presented in this research is the incorporation of pH-sensitive hydrogels with long period gratings for the development of a fiber optic-based pH sensor. Optical fiber-based pH sensors offer numerous advantages in wastewater monitoring, blood diagnostics, bioremediation, as well as chemical and food processing. Specifically this research focuses on pH sensors that can be multiplexed with other chemical sensors for a complete chemical analysis of the corrosive environment. / Master of Science

A research report submitted to the Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, in partial ful lment of the requirements for the degree of Master of Science in Engineering. Johannesburg, 2015 / Control of systems are important in most industrial sectors, they nd applications in electronics, machine design and navigation. These control systems often use sensors to work e ectively. One such sensor is an accelerometer, which is used to measure acceleration with one or more degrees of freedom. This research report investigates the modelling, system identi cation and controller design for an accelerometer, a Fibre Optic Accelerometer (FOA). Such a device may be applied in many applications such as anti-skid control, structural failure in buildings and bridges, as well as strategic missile guidance. This report presents a model of a FOA demonstrator which crudely models an industrially developed accelerometer, the demonstrator is made of a jig consisting of a guitar string and electromagnets. Such a model needs to account for a distributed parameter beam combined with a permanent magnet and four electromagnets. The guitar string is modelled using three beam models, namely a spring/damper model, an Assumed Modes Model (ASM) and a Transfer Function Model (TFM). The parameters for these beam models are identi ed using the Nelder-Mead simplex algorithm and the least squares method. The electromagnets within the jig, are modelled using a mathematical model obtained through curve tting of experimental data. The overall FOA sensor is optimised using a lead-lag controller. Five cost functions where investigated, these cost functions are H1, Integral Square Error (ISE), Integral Absolute Error (IAE), Integral Time Square Error (ITSE) and Integral Absolute Time Error (IATE). It was found that the guitar string may be modelled using a single degree of freedom beam model. This is based on a number of reasons, such as the aperture size - through which the tip Light Emitting Diode (LED) projects, the tip mass (permanent magnet) - acting as a natural damper and the fact that Position Sensing Device (PSD) only measures the tip position. It was found that a single degree of freedom model in two orthogonal axes, with a single link beam spring/damper model was the most suitable representation of the guitar string. And the IAE lead-lag controller was found to be the most e ective in controlling a guitar string, this e ectiveness was due to least settling time. / MT2017