Traditional implementations of optical receivers are designed to operate with external photodetectors or require integration in a hybrid technology. By integrating a CMOS photodetector monolithically with an optical receiver, it can lead to the advantage of speed performance and cost. This dissertation describes the implementation of a photodetector in CMOS technology and the design of an optical receiver front-end and a clock and data recovery system. The CMOS detector converts the light input into an electrical signal, which is then amplified by the receiver front-end. The recovery system subsequently processes the amplified signal to extract the clock signal and retime the data. An inductive peaking methodology has been used extensively in the front-end. It allows the accomplishment of a necessary gain to compensate for an underperformed responsivity from the photodetector. The recovery circuits based on a nonlinear circuit technique were designed to detect the timing information contained in the data input. The clock and data recovery system consists of two units viz. a frequency-locked loop and a phase-locked loop. The frequency-locked loop adjusts the oscillator’s frequency to the vicinity of data rate before phase locking takes place. The phase-locked loop detects the relative locations between the data transition and the clock edge. It then synchronises the input data to the clock signal generated by the oscillator. A system level simulation was performed and it was found to function correctly and to comply with the gigabit fibre channel specification. / Dissertation (MEng (Micro-Electronics))--University of Pretoria, 2007. / Electrical, Electronic and Computer Engineering / unrestricted

Disertační práce se zabývá optickým digitálně-analogovým převodníkem, jako alternativou optické části koncové vysílací jednotky (optický front-end) určené pro VLC (visible light communication) aplikace. Stěžejní část práce, která se věnuje numerickému modelování optického kanálu, prezentuje vliv bitové hloubky, topologie koncové části optického vysílače a geometrického uspořádání na přenášený signál. Součástí práce je návrh, realizace a ověření parametrů optického digitálně-analogového převodníku vycházející z předcházejících simulací. V poslední řadě práce obsahuje demonstraci vysokorychlostní optické komunikace s využitím navrženého VLC optického vysílače.

This dissertation thesis deals with a long range free space optical links for communication over the distance of few tens of kilometers in the atmosphere. The problematic of the beam propagation and atmospheric effects influencing the beam and the quality of the communication protocol are discussed. The measuring link is also designed to study the parameters of the communication link work conditions. The measuring link consists of two heads. The transmitter head is designed to use two optical beams with laser diodes at the wavelength of the atmospheric windows 850 or 1550 nm and the overall power of hundredths of mW. The receiver head includes the Fressnel lens. For the detection of very weak signal, the avalanche photodiode is used. In the end of this work, due to the high power of the transmitting optical beam, the laser safety conditions are also discussed, including the deduced optical transmitters construction recommendations.

This work is focused on free space optical communication in visible electromagnetic spectrum known as visible light communication (VLC). Basic parameters of standard IEEE 802.15.7, advantages and disadvantages are discussed in the theoretical part of this work. Furthermore, optical link and it´s parts are described. The largest part of the work is focused on design and simulation of optical receiver for visible spectrum. Selection of component, noise and SNR calculation is discussed as well. This work also includes calculation of power energy in different parts of optical connection, PCB design of optical receiver, transmitters and power supply and output board. Behavior and parameters of electronic circuits, components and optical connection are explored, measured and compared with theoretical values.

No description available.

The dissertation investigates the optical time domain reflectometer (OTDR) systems. The main object of research is an optical receiver for OTDR. The aim of the work is to create an optical receiver design method-ology to achieve optimal dynamic range of the system for a given band-width, design and investigate integrated fully differential variable gain tran-simpedance amplifier for OTDR optical receiver. Main tasks solved in this work are: perform analysis of OTDR struc-tures, main specifications and suggest possible improvement approaches; analyze main optical receiver noise sources and noise minimization and create generalized noise model; create optical receiver for an OTDR design methodology, that allow calculating avalanche photodiode multiplication factor, transimpedance amplifier feedback resistance and voltage amplifier input transistor dimensions that achieves optimal OTDR dynamic range; design and perform simulations of transimpedance amplifier integrated cir-cuit using AMS 0.35 µm CMOS technology and calculate optical receiver parameters in 0.1–100 MHz range of bandwidths The dissertation consists of four parts including Introduction, 4 chap-ters, Conclusions, References and 1 Annex. The introduction reveals the investigated problem, importance of the thesis and the object of research. It also describes the purpose and tasks, research methodology, scientific novelty, the practical significance of re-sults examined in the paper and defended statements. The... [to full text] / Disertacijoje nagrinėjamos laiko srities optinės reflektometrinės (OTDR) sistemos. Pagrindinis tyrimo objektas yra OTDR įėjimo pakopa – optinis imtuvas (OI). Disertacijos tikslas – sukurti OI projektavimo metodiką, lei-džiančią pasiekti optimalų dinaminį diapazoną, suprojektuoti ir ištirti integ-rinį diferencinį pereinamos varžos stiprintuvą (PVS) su kintamu stiprinimo koeficientu. Darbe sprendžiami šie uždaviniai: atliekama OTDR ir jų pagrindinių charakteristikų analizė ir formuluojamos tobulinimo kryptys; analizuojami pagrindiniai optinio imtuvo triukšmų šaltiniai, jų mažinimo galimybės ir su-daromas apibendrintas optinio imtuvo triukšmų modelis; sukuriama OI pro-jektavimo metodika, leidžianti apskaičiuoti griūtinio fotodiodo dauginimo faktorių, pereinamosios varžos stiprintuvo grįžtamojo ryšio varžą ir įėjimo tranzistoriaus fizinius matmenis, kuriems esant gaunamas optimalus dina-minis diapazonas; projektuojamas optinio imtuvo maketas iš diskrečiųjų elementų ir tiriami jo parametrai; atliekamas integrinio PVS projektavimas ir modeliavimas, taikant 0,35 µm KMOP technologiją bei optinio imtuvo pa-rametrų skaičiavimas 0,1–100 MHz dažnių juostų diapazone. Disertaciją sudaro įvadas ir keturi skyriai. Pabaigoje pateikiami naudo-tos literatūros ir autoriaus publikacijų disertacijos tema sąrašai ir 1 priedas. Įvadiniame skyriuje aptariama: tiriamoji problema, darbo aktualumas, aprašomas tyrimų objektas, suformuluotas darbo tikslas bei uždaviniai, ap-rašoma tyrimų metodika... [toliau žr. visą tekstą]

This thesis deals with the structure of the optical wireless link intended for indoor applications. Optical transmitters and optical receivers as the basic elements of optical links and their characteristics and parameters are described. The characteristics of lenses used in the transmitter and receiver are presented. The special chapter is devoted to the directional reflectance properties of surfaces. The last part of the thesis is focused on a specific proposal of the wireless optical links and its power level diagram.

Advances in fiber optic communications and the convergence of the optical-wireless network will dramatically increase the network heterogeneity and complexity. The goal of our research is to create smart receivers that can autonomously identify and demodulate, without prior knowledge, nearly any signal emerging from the next-generation of high-speed optical communication networks.

Theme of this thesis is using of universal module LabJack U3-HVTM as support for physics lessons. This thesis describes the universal module LabJack U3-HVTM and evaluation method of measured value on the computer screen using software eSimLab. To all physical tasks is described path of signal with measured string from developed sensor until evaluation of signal in the computer. In the thesis is specifically described a function of developed sensors of physical quantities, there are subscribed diagrams including PCB and parts list. The thesis is including designed physical tasks for monitoring of atmospheric pressure, temperature, wind direction, sunshine duration and the role of measurement of the signal on the optical transmitter using the developed sensors and universal module LabJack U3-HVTM.

The thesis analyzes the optical laser range finders in real propagation environments. Itdescribes the various parts of optical laser range finders their properties and principles in relation to their performance balance. The paper presents the basic optical properties of lenses used in the transmitter and receiver. A separate chapter is devoted to the transit time method and factors influencing the measurement. The proportional directional reflectance analysisis a part of the thesis. In conclusion, the thesis contains the practical laboratory measurements of the relative directional reflectance of different materials and colors, and verification of the power level diagram.