In this thesis, we analyze the performance of heterogeneous wireless communication systems that are composed of Optical Wireless Communication (OWC) and Radio Frequency (RF) systems. OWC systems further include long range outdoor Free Space Optical (FSO) systems and short range indoor Visible Light Communication (VLC) systems. Hybrid FSO/RF systems have emerged as a promising solution for high data rate wireless transmissions. Various transmission schemes including switch-over and soft-switching had been presented for hybrid FSO/RF systems. To overcome the drawbacks of existing schemes, we present a new transmission strategy for hybrid FSO/RF systems exploring an adaptive combining technology. This new strategy shows an improved outage performance. Typically, when the transmitter and the receiver are provided with channel state information, the transmission schemes can be adaptively designed allowing the channel to be used more efficiently. We present two new joint adaptive transmission schemes for hybrid FSO/RF systems. The first one is joint adaptive modulation and adaptive combining scheme which improves the spectral efficiency of hybrid FSO/RF systems. The other one is joint power adaptation and adaptive combining scheme which improves the throughput and the outage performance of hybrid FSO/RF systems. We accurately evaluate the performance of both schemes. FSO technology can be used effectively in multiuser scenarios to support Point-to-Multi-Point (P2MP) networks. In P2MP networks, FSO links are used for data transmission from a central location to multiple users. In this thesis, we present a new P2MP network based on hybrid FSO/RF transmission system. A common backup RF link is used by the central station for data transmission to any user in case of the failure of its corresponding FSO link. Based on a Markov Chain formulation, we study the performance of the resulting system. P2MP Hybrid FSO/RF network achieves considerable performance improvement over the P2MP FSO-only network. In VLC, Light Emitting Diode (LED) is used for the purpose of simultaneous illumination and data communication at high data rate. However, the light originating from a LED source is naturally confined to a small area and is susceptible to blockages. Hybrid VLC/RF systems have been emerged as a promising solution to provide enhanced communication coverage. We introduce a new dual-hop VLC/RF system with energy harvesting relay to extend the coverage of indoor wireless system based on VLC. The second-hop RF transmission uses the harvested energy over the first-hop VLC transmission. In this thesis, we propose two different approaches for energy harvesting at the relay terminal. In the first approach, the relay harvests light energy from different artificial light sources and sunlight entering the room. In this approach, we propose a novel statistical model for the harvested electrical power and analyze the probability of data packet loss. In the second approach, the relay harvests energy from the VLC link by extracting the direct current component of the received optical signal. In this approach, we investigate the optimal design of the hybrid VLC/RF system in terms of data rate maximization. In both cases, we present extensive numerical examples to define important design guide lines for VLC/RF systems. / Graduate

Optical wireless communications (OWC) has the potential to become a remedy for the shortage of the radio frequency (RF) spectrum. Especially in indoor environments, OWC could enable wireless home networking systems which offload data traffic from existing RF systems. In OWC, data is transmitted by modulating the intensity of light sources, typically incoherent light emitting diodes (LEDs). Thus, OWC systems employ intensity modulation (IM) and direct detection (DD) of the optical carrier. Since off-the-shelf LEDs have a limited modulation capability, the transmission bandwidth of practical OWC systems is restricted. Consequently, the available bandwidth has to be used efficiently. In this thesis, spectrally efficient optical wireless transmission techniques are evaluated. Firstly, multiple transmitter-receiver techniques are investigated. These multiple-input-multiple-output (MIMO) techniques provide high spectral efficiency, and therefore high data rates. Specifically, the MIMO techniques repetition coding (RC), spatial multiplexing (SMP) and spatial modulation (SM) are analysed for indoor OWC. The performance of these techniques is evaluated analytically and by means of computer simulations. It is shown that inducing power imbalance between the multiple optical transmitters can substantially improve the performance of optical MIMO techniques as the power imbalance improves the differentiability of the multiple channels. In addition, it is found that link blockage and the utilisation of transmitters having different optical wavelengths enhance channel differentiability as well. These methods enable the utilisation of optical MIMO techniques under conditions which typically disallow the application of MIMO schemes due to little differences between the multiple links. Secondly, a novel optical wireless transmitter concept is developed. This concept uses discrete power level stepping to generate intensity modulated optical signals, such as orthogonal frequency division multiplexing (OFDM) waveforms. The transmitter consists of several on-off-switchable LED groups which are individually controlled to emit scaled optical intensities. As a result, the digital-to-analogue conversion of the signals to be sent is done in the optical domain. This method enables the implementation of low-complex and power-efficient optical transmitter front-ends – the major shortcoming of conventional optical OFDM transmitters. Thirdly, a novel approach for wireless data transmission within an aircraft cabin is presented. The data is transferred by 2-dimensional visual code sequences. These sequences are displayed on the in-flight entertainment (IFE) screen and are captured by the built-in camera of a user device which acts as receiver. Transmission experiments within an aircraft cabin mock-up demonstrate the functionality of the implemented system under realistic conditions, such as ambient illumination and geometric configuration. Altogether, this thesis has analysed the potential of spectrally efficient optical wireless transmission techniques. It is shown that OWC systems can greatly benefit from these techniques.

No description available.

Optical wireless communication (OWC) offers many benefits over established radio frequency–based communication links. Particularly in, high-data services, high security, and license-free operation, OWC link are becoming an attractive solution for the next generation of communication systems. In OWC, precise alignment of the incoming beam is necessary to close the communication link. However, precisely aligning the beam between the transceivers is challenging due to the laser beam’s narrowness and external disturbances that can significantly reduce, destroy, or scatter the beam signal. Therefore, designing optimized control strategies can significantly improve the alignment precision, which is the main motivation for this work. This thesis deploys standard and optimal control techniques, with an emphasis on optimized control strategies, to address the alignment problem in underwater optical wireless communication (UOWC) and in laser beam stabilizer systems within a vibrating environment. First, the UOWC system’s alignment problem was investigated in a vibrating scenario. For its effective control, the properties of light propagation were considered by accounting for the dynamical model that describes the propagation characteristics of the signal beam between transceivers. To control the UOWC system, we designed an observer-based optimal controller approach that combined the unconstrained and constrained optimal controllers, namely linear quadratic regulator (LQR) and model predictive control (MPC) with the extended Kalman filter (EKF). The latter enabled estimations of the beam dynamics from the power of the received beam signal. Extensive simulation tests were conducted that demonstrated the efficiency of the MPC algorithm compared to the LQR, fractional order proportional integral derivative (FOPID) and conventional PID controllers in terms of tracking and robustness against the disturbance levels. Second, the alignment problem in the laser beam stabilizer system was considered, whereby the designed control algorithms were tested experimentally in a vibrating disturbance. For this particular system, the LQR and MPC optimal controllers were designed both in simulation and experimental environments. The designed optimal control algorithms were compared to a conventional PID controller and its optimized variants (e.g., fractional and robust), demonstrating the MPC design’s outperformance in terms of tracking error and robustness to different voltage disturbance levels.

The COVID-19 global pandemic forced long lock-downs and physical distancing in different world regions. As a consequence, many jobs, services, and courses switched to online mode. This sudden turn of events created a dramatic increase in internet bandwidth demand, which has reached crisis point—even in developed countries—and widened the gap between those living in cities and far-flung regions. Installing new optical fibers to extend the capacity can be expensive. Radiofrequency (RF) is cur- rently the technology of choice to satisfy the bandwidth demand in under-connected regions, but is bandwidth-limited and strictly regulated. Connecting the unconnected via laser beams propagating in the atmosphere can be an efficient solution to provide fiber-like connectivity, while also being economically profitable. Free-space optics (FSO) is an unlicensed technology that uses infrared links to connect two communi- cating terminals. FSO systems can be running quickly compared to RF ones. FSO is also seen as a potential solution to provide high-speed connectivity between satellites and ground stations, and fly unmanned aerial vehicles (UAVs) and ground terminals. However, FSO is subject to various channel-related challenges, including atmospheric attenuation, turbulence, and pointing errors. In this thesis, we develop an FSO chan- nel simulation tool that considers the various effects that could potentially occur in terrestrial and vertical channels. We extend our study to cover structured light beams, which have been intensively considered in the last decade, as an extra degree of freedom for FSO. Finally, we consider realistic meteorological data from different regions in the Kingdom of Saudi Arabia to identify the best locations to deploy FSO systems.

The need for wireless connectivity is ever increasing while conventional radio frequency (RF) communications are limited by the amount of available spectrum. Visible light communications (VLC) are emerging as a promising complementary to the RF wireless, thanks to the enormous available bandwidth in the visible spectrum. Moreover, VLC integrates into the ubiquitous illumination infrastructures to satisfy the need for wireless connectivity indoors. Commercially available light-emitting diodes (LEDs) are low-cost, simple, and have a small modulation bandwidth. For the small modulation bandwidth, VLC systems must enjoy high spectral efficiency to achieve high-rate transmission. Additionally, VLC systems must have high power efficiency to help preserve the critical advantage of LEDs for illumination applications. Furthermore, since LED luminaires are constrained by cost, deployed VLC systems must be low-complexity. Indoor VLC channels are dispersive due to multipath propagation indoors and due to the limited bandwidth of the optoelectronics. However, time-domain equalization on such channels can be prohibitively expensive for long serials. These challenges motivate extensive research on optical orthogonal frequency division multiplexing (OFDM). Given those problems and challenges, this thesis introduces novel spectrum- and power-efficient optical OFDM modulation schemes to implement with low complexity in VLC systems. Firstly, absolute value layered asymmetrically clipped optical OFDM (ALACO-OFDM) is presented to achieve high spectral efficiency and high power efficiency with fewer layers, thus requiring low complexity. Compared to its counterparts, ALACO-OFDM can achieve higher spectral efficiency and information rate even with fewer layers. Antisymmetry-constructed clipped optical OFDM (AC-OFDM) is then introduced as a novel low-complexity modulation scheme. To enhance the spectral efficiency and retain low-complexity, layered AC-OFDM (LAC-OFDM) is introduced, consisting of several layers of AC-OFDM signals. LAC-OFDM is shown to be less complex compared to its state-of-the-art counterparts. Concerning a practical VLC dispersive channel, low-complexity layered ACO-OFDM (L-LACO) is introduced with simple equalization. Mathematically, L-LACO generates identical signals to the existing layered asymmetrically-clipped optical OFDM (LACO-OFDM); however, it requires only half arithmetic operations at both the transmitter and the receiver. For a practical bandlimited VLC dispersive channel, the previous optical OFDM modulation schemes will be no longer non-negative after interpolation with sinc(t) pulse. This thesis presents Kramers-Kronig (KK) optical OFDM (KKO-OFDM) to enhance the spectral efficiency and power efficiency for such bandlimited VLC channels. The KKO-OFDM transmit signal is constructed to be real-valued, non-negative, and strictly bandlimited. Numerical results show that KKO-OFDM outperforms DCO-OFDM and LACO-OFDM in bandlimited VLC channels in terms of optical power efficiency. / Thesis / Doctor of Philosophy (PhD) / Visible light communications (VLC) integrate into the ubiquitous light-emitting diode (LED) luminaires, providing lighting and communication simultaneously. Commercially available LEDs are low-cost, simple, and have a limited modulation bandwidth. These LEDs demand that VLC orthogonal frequency division multiplexing (OFDM) modulation schemes be spectrum- and power-efficient with low complexity. Concerning these challenges, this thesis presents a novel spectrum- and power-efficient VLC OFDM scheme with low complexity. Firstly, absolute value layered asymmetrically clipped optical OFDM (ALACO-OFDM) is presented to achieve high spectral and power efficiency while requiring fewer layers. Then layered antisymmetry-constructed clipped optical OFDM (LAC-OFDM) is introduced, which requires low complexity as compared to existing layered asymmetrically-clipped optical OFDM (LACO-OFDM). Given a VLC dispersive channel, low-complexity LACO-OFDM (L-LACO) is furthermore introduced with simple equalization but generates an identical signal to the existing LACO-OFDM. Finally, for a bandlimited VLC channel, Kramers-Kronig optical OFDM (KKO-OFDM) is presented to achieve high spectral and power efficiency. The ALACO-OFDM and LAC-OFDM work in flat VLC line-of-sight links while L-LACO in VLC dispersive links and KKO-OFDM in bandlimited VLC dispersive links with simple equalizer.

International Telemetering Conference Proceedings / October 20-23, 2003 / Riviera Hotel and Convention Center, Las Vegas, Nevada / Wireless interfaces are becoming ubiquitous in terrestrial applications ranging from local area networking in business and commercial environments to large scale factory automation and process control. The pressure to develop these wireless interfacing techniques has come from the need to reduce cabling, reduce installation costs, and make it easier to extend network infrastructures. Concerns about electromagnetic compatibility, safety, reliability, and security have lead to the development of techniques and protocols that enable such wireless interfaces to be operated in electromagnetically harsh environments, without generating unacceptable interference, and providing reliable, dependable and secure data communications. On the face of it, the use of wireless interfaces onboard spacecraft looks like a good way of reducing the spacecraft harness mass and bulk. However, recent work by the European Space Agency has shown that, while harness reduction will undoubtedly be one benefit of using wireless interfaces, they offer many other benefits that will be more significant in the near future. Amongst these are significant advantages during integration and testing, the ability to retrofit and upgrade facilities, and cable replacement in moving structures such as robotic arms. In this paper we briefly survey the benefits of wireless interface technologies for spacecraft onboard use, and identify the challenges involved in adapting them for flight use. We then look at the considerations that should be taken into account in establishing the financial case for developing wireless interface technologies for flight applications.

Optical wireless communication (OWC) is a promising alternative to radio frequency (RF) communication with a significantly larger and unregulated spectrum. Impairments in the physical layer, such as the non-linear transfer characteristic of the transmitter, the dispersive optical wireless channel and the additive white Gaussian noise (AWGN) at the receiver, reduce the capacity of the OWC system. Single-carrier multi-level pulse position modulation (M-PPM) and multilevel pulse amplitude modulation (M-PAM) suffer from inter-symbol interference (ISI) in the dispersive channel which reduces their capacity even after channel equalization. Multi-carrier modulation such as optical orthogonal frequency division multiplexing (O-OFDM) with multilevel quadrature amplitude modulation (M-QAM) is known to maximize the channel capacity through bit and power loading. There are two general signal structures: bipolar Gaussian signal with a direct current (DC) bias, i.e. DC-biased O-OFDM (DCO-OFDM), or unipolar half- Gaussian signal, employing only the odd subcarriers, i.e. asymmetrically clipped O-OFDM (ACO-OFDM). In this thesis, the signal distortion from the transmitter nonlinearity is minimized through pre-distortion, optimum signal scaling and DC-biasing. The optical front-ends impose minimum, average and maximum optical power constraints, as well as an average electrical power constraint, on the information-carrying signals. In this thesis, the optical signals are conditioned within these constraints through optimum signal scaling and DC-biasing. The presented analysis of the optical-to-electrical (O/E) conversion enables the derivation of the electrical signal-to-noise ratio (SNR) at the receiver, including or excluding the additional DC bias power, which is translated into bit-error rate (BER) performance. In addition, a generalized piecewise polynomial model for the non-linear transfer characteristic of the transmitter is proposed. The non-linear distortion in O-OFDM is translated by means of the Bussgang theorem and the central limit theorem (CLT) into attenuation of the data-carrying subcarriers at the receiver plus zero-mean complex-valued Gaussian noise. The attenuation factor and the variance of the non-linear distortion noise are derived in closed form, and they are accounted towards the received electrical SNR. Through pre-distortion with the inverse of the proposed piecewise polynomial function, the linear dynamic range of the transmitter is maximized, reducing the non-linear distortion to double-sided signal clipping. Finally, the OWC schemes are compared in terms of spectral efficiency and electrical SNR requirement as the signal bandwidth exceeds the coherence bandwidth of the optical wireless channel for a practical 10 dB linear dynamic range. Through optimum signal scaling and DCbiasing, DCO-OFDM is found to achieve the highest spectral efficiency for a target SNR, neglecting the additional DC bias power. When the DC bias power is counted towards the signal power, DCO-OFDM outperforms PAM with linear equalization, approaching the performance of the more computationally intensive PAM with non-linear equalization. In addition, the average optical power in O-OFDM is varied over dynamic ranges of 10 dB, 20 dB and 30 dB. When the additional DC bias power is neglected, DCO-OFDM is shown to achieve the Shannon capacity, while ACO-OFDM exhibits a 3 dB gap which grows with higher SNR targets. When the DC bias power is included, DCO-OFDM outperforms ACO-OFDM for the majority of average optical power levels with the increase of the SNR target or the dynamic range.

Optical wireless communication, taking advantage of the unlicensed ultraviolet-to visible wavelength region of the electromagnetic spectrum, had been coined as the next-generation wireless communication technology and holds promises to deliver a high-speed, reliable, and secured broadband experience. The push towards the optical-based medium is manifested by the demand for additional channel bandwidth to accommodate the rapid growth of the Internet-of-Things (IoT) and Internet-of-Underwater-Things (IoUT). Therefore, high-bitrate optoelectronics devices and components forming the transceiver units used in an optical wireless communication system require substantial progression to accelerate the development of this paradigm-shifting technology. In this dissertation, we demonstrated a plethora of optical detection platforms to circumvent the existing long-standing issues related to modulation bandwidth, wavelength-selectiveness, and solar-blind ultraviolet-C detection found in conventional planar silicon-based optical detectors. Herein, we presented the semipolar group-III-nitride-based micro-photodiodes for enabling up to Gbit/s optical detection in the ultraviolet-to-violet domain. The wavelength-selectiveness nature of the micro-photodiodes enabled a bitrate of up to 1.5 Gbit/s based on a power-saving on-off-keying modulation scheme. While it offers a high bitrate for the optical communication link, it restricts its detection size and angle-of-view due to the conventional resistance-capacitance and étendue limits. Therefore, we also explored using polymer-based scintillating fibers as a high-speed and near-omnidirectional optical detection platform to cater to various dynamic scenarios in optical wireless communication. The detection platform formed by the scintillating fibers enabled near-omnidirectional and large-area optical detection without sacrificing the modulation bandwidth. These investigations paved the way towards relieving the resistance-capacitance limit while addressing the pointing, acquisition, and tracking issue in underwater wireless optical communication. Subsequently, we also presented a novel wavelength-converting mechanism based on halide-perovskite nanocrystals and a conventional silicon-based platform. This demonstration addressed the lack of ultraviolet-C optical detectors in the existing market and enabled future solar-blind optical communication links. Finally, we also presented on halide-perovskite polymer-based scintillating fibers as the high-bitrate and near-omnidirectional optical detection platform. Our studies successfully addressed the existing inadequacy for high-bitrate photodetection. These works could play a significant role in progressing the technology forward, based on bottom-up material and devices innovation, to offer a reliable internet connection to the future highly interconnected society.

Single-photon avalanche diodes (SPADs) capable of single photon detection are promising optical sensors for use as receivers in optical wireless communication (OWC) systems. In SPAD-based receivers, the intersymbol interference (ISI) effect caused by dead time is an important drawback that limits performance. In this thesis, we propose two novel SPAD operation receivers to reduce the ISI effect in SPAD-based OWC. To validate the feasibility of these two modes, we design a free-running SPAD front-end circuit with post-layout transient simulation results. This SPAD circuit is improved by a novel mixed passive-active quench and reset front-end circuit that achieves a very short dead time. Based on the traditional free-running mode, we design the clock-driven mode and time-gated mode to reduce the ISI effect through time-controlled operating signals. In this work, we develop a new simulation system to assess the ISI effect in On-Off Keying (OOK) modulated communication and pulse position modulated (PPM) communication. To accurately evaluate these three modes, we build a OWC platform to test our proposed SPAD receiver manufactured by TSMC 65 nm process. The Test results demonstrate that the clock-driven mode and time-gated mode receivers can improve the bit error rate (BER) performance in low data rate communication and high data rate high optical power communication, respectively. Moreover, compared to the free-running mode, the two proposed time-controlled modes achieve higher data rate communication and better noise tolerance ability in SPAD-based OWC. / Thesis / Master of Applied Science (MASc) / Optical communication involves using light as a signal to transmit information, and it is currently a highly popular field of research. However, optical receivers used in this type of communication often require specific conditions, which can limit the overall performance of the communication system. To address this issue, we have developed an optical sensor tailored for optical communication. This sensor boasts exceptional sensitivity, allowing it to detect individual particles of light, thereby substantially reducing the demand for signal intensity in the optical communication system. Moreover, we have devised three operational circuits that enhance the sensor's responsiveness to signals under specific communication conditions. We have created a mathematical model to evaluate the proposed optical sensor and the designed circuits, and subsequently manufactured the optical sensor. Both the simulation results and the actual test outcomes unequivocally demonstrate that our proposed sensor has the potential to enhance the performance of optical communication systems.