<p>Electrochemical Transistor(ECT) was reported by David Nilsson in 2002. Later,its dimensios were specified and a SPICE model was developed.</p><p>The main purpose of this diploma work is to check the performance of electrochemical transistors in amplifier circuits. Simple amplifier circuits were simulated using SPICE model of ECT. Lateral and Vertical structures of electrochemical transistors were patterned on orgacon sheet(provided by AGFA),with various electrolytes(EG010,MS-HEC & MS-L). Characteric curves and time responses of these transistors were studied and then were then used as an active component in single amplifier circuits. Screen printed ECT's were also checked with the best available electrolyte. Behaviour of self made and screen printed ECT's were compared on the basis of on-off ratio,slew rate,frequency response and gain. Screen printed transistors showed promising results having less deterioration with time  but  till  an  an  input  signal  frequency  of  2Hz  only. Mismatch with simulation results and Shockley's equation were other findings after data analysis.</p><p><img src="file:///C:/DOCUME%7E1/zia/LOCALS%7E1/Temp/moz-screenshot.jpg" /><img src="file:///C:/DOCUME%7E1/zia/LOCALS%7E1/Temp/moz-screenshot-1.jpg" /></p>

Symmetric and fast (∼5 ms) on-to-off and off-to-on drain current switching characteristics have been obtained in screen printed organic electrochemical transistors (OECTs) including PEDOT:PSS (poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonic acid)) as the active transistor channel material. Improvement of the drain current switching characteristics is made possible by including a carbon conductor layer on top of PEDOT:PSS at the drain electrode that is in direct contact with both the channel and the electrolyte of the OECT. This carbon conductor layer suppresses the effects from a reduction front that is generated in these PEDOT:PSS-based OECTs. In the off-state of these devices this reduction front slowly migrate laterally into the PEDOT:PSS drain electrode, which make off-to-on switching slow. The OECT including carbon electrodes was manufactured using only standard printing process steps and may pave the way for fully integrated organic electronic systems that operate at low voltages for applications such as logic circuits, sensors and active matrix addressed displays. / <p>Funding Agencies|Lintec Corporation||</p>

Glödlampan, en gång symbolen för mänsklig uppfinningsförmåga, är idag på väg att försvinna. Lysdioder och lågenergilampor har istället tagit över då dessa har betydligt längre livstid och högre effektivitet. Den tidigare så hyllade glödlampan anses numera vara en miljöbov, och förbud och restriktioner mot den blir allt vanligare. Trots detta så är de nya alternativen bara att betrakta som provisoriska steg på vägen mot en ideal ljuskälla, som idag tyvärr inte existerar. Lågenergilampor innehåller exempelvis kvicksilver, och utgör därmed ett direkt hot mot en användares hälsa. Både lysdioder och lågenergilampor består även av höga halter av andra tungmetaller, och är väldigt komplicerade att tillverka. Återvinning är därför ett måste, och en fullödig energibesparingsanalys måste ta hänsyn till den betydande energin som går åt vid tillverkningen. Till viss del kan detta lösas genom att göra komponenterna små och ljusstarka, men för att göra en sådan belysning angenäm används istället utrymmeskrävande och ofta energislukande lampskärmar. Lysdioder och lågenergilampor är helt enkelt bra, men långt ifrån perfekta.All elektronisk utrustning är idag beroende av metaller och inorganiska halvledare, vilket gör återvinning viktig och tillverkning komplicerad. Detta är kanske på väg att ändras då även organiska material, t.ex. plast, har visat sig kunna ha elektroniska egenskaper. Idag är organisk elektronik ett hett forskningsområde där material med liknande egenskaper som plast, fast med funktionella elektroniska egenskaper, undersöks och appliceras. Något som gör organiska material extra intressanta är att många kan lösas upp i vätskor, vilket möjliggör för skapandet av bläck. Detta leder i sin tur till möjligheter för användandet av storskaliga trycktekniker, t.ex. tidningspressar och bläckstråleskrivare, vilka leder till en stor kostnadsreduktion och förenklad tillverkning av lysande komponenter. Idag har plast redan ersatt många andra material i en mängd olika tillämpningar. Plastflaskor är vanligare än glasflaskor, och ylletröjor konkurerar idag med kläder gjorda av fleece och andra syntetiska fibrer. Med ljusemitterande plast finns det helt klart en möjlighet att en liknande utveckling kan ske även för lampor.Den här avhandlingen fokuserar på den fortsatta utvecklingen av den ljusemitterande elektrokemiska cellen (LEC), som 1995 uppfanns av Pei et al. LEC-tekniken använder sig av organiska halvledare för att konvertera elektrisk ström till ljus, men även en elektrolyt som möjliggör elektrokemisk dopning. Detta förbättrar den organiska halvledarens elektroniska egenskaper signifikant, vilket leder till mindre resistans och högre effektivitet hos den färdiga lysande komponenten.Visionen för denna och besläktade tekniker har sedan länge varit förverkligandet av en lysande tapet. Den här avhandlingen har försökt närma sig denna vision genom att visa hur en LEC kan uppnå hög effektivitet och lång livslängd, och samtidigt tillverkas i luft med storskaliga produktionsmetoder. Orsaker till en tidigare begränsad livslängd har identifierats och minimerats med hjälp av nya komponentstrukturer och materialformuleringar. En inkapslingsmetod presenteras också, vilken skyddar komponenten från syre och vatten som annars lätt reagerar med det dopade organiska materialet. Detta resulterar i en signifikant förbättring av livslängden.Genom att använda slot-die bestrykning och sprayning, båda kompatibla med rulle-till-rulle tillverkning, har möjligheter för storskalig produktion demonstrerats. Slutligen har en speciell metod för spraymålning av stora lysande ytor utvecklats. / The incandescent light bulb, once the very symbol for human ingenuity, is now being replaced by the next generation of lighting technologies such as the compact fluorescent lamp (CFL) and the light emitting diode (LED). The higher efficiencies and longer operational lifetimes of these new sources of illumination have led to the demise of the classic traditional bulb. However, it should be pointed out that the light sources that are taking over are better, but not perfect. The complex high-voltage electronic circuits and health hazardous materials required for their operation make them far from a sustainable eco-friendly option. Their fabrication is also complex, making the final product expensive. A new path forward might be through the use of plastics or other organic materials. Though not traditionally seen as electronically active, some organic materials do behave like inorganic semiconductors and substantial conductivity can be achieved by doping. Since plastics can be easily molded into complex shapes, or made into an ink using a solvent, it is expected that organic materials could revolutionize how we fabricate electronic devices in the future, and possibly replace inorganic crystals in the same way as plastics have replaced glass and wool for food storage and clothes. This thesis has focused on the light-emitting electrochemical cell (LEC), which was invented by Pei et al. in 1995. It employs organic semiconductors that can convert electricity to light, but also an electrolyte that further enhances the electronic properties of the semiconductor by allowing it to be electrochemically doped. This allows light-emitting films to be driven by a low-voltage source at a high efficiency. Unfortunately, the electrolyte has been shown to facilitate rapid degradation of the device under operation, which has historically severely limited the operational lifetime. Realizing the predicted high efficiency has also proven difficult. The purpose of this thesis is to bridge the gap between the LEC and the CFL. This is done by demonstrating efficient devices and improved operational lifetimes. Possible degradation mechanisms are identified and minimized using novel device architectures and optimized active layer compositions. An encapsulation method is presented, and shown to increase the LEC stability significantly by protecting it from ambient oxygen and water. The thesis further focuses on up-scaled fabrication under ambient air conditions, proving that light-emitting devices are compatible with solution-based and cost-efficient printing. This is achieved by a roll-to-roll compatible slot-die coating and a novel spray-depositing technique that alleviates problems stemming from dust particles and phase separation. A practical ambient air fabrication and a subsequent operation of light-emitting electrochemical cells with high efficiency are thus shown possible.

Polymers are very attractive materials that can be tailored for specific needs and functionalities. Based on their chemical structure, they can for instance be made electrically insulating or semiconducting with specific mechanical properties. Polymers are often processable from a solution, which enables the use of conventional low-cost and high-volume manufacturing techniques to print electronic devices onto flexible substrates. A multitude of polymer-based electronic and electrochemical devices and sensors have been developed, of which some already has reached the consumer market. This thesis focuses on polarization characteristics in polyelectrolyte-based capacitor structures and their role in sensors, transistors and supercapacitors. The fate of the ions in these capacitor structures, within the polyelectrolyte and at the interfaces between the polyelectrolyte and various electronic conductors (a metal, a semiconducting polymer or a network of carbon nanotubes), is of outermost importance for the device function. The humidity-dependent polarization characteristics in a polyelectrolyte capacitor are used as the sensing probe for wireless readout of a passively operated humidity sensor circuit. This sensor circuit can be integrated into a printable low-cost passive sensor label. By varying the humidity level, limitations and possibilities are identified for polyelectrolyte-gated organic field-effect transistors. Further, the effect of the ionic conductivity is investigated for polyelectrolyte-based supercapacitors. Finally, by using an ordinary electrolyte instead of a polyelectrolyte and a high-surface area (supercapacitor) gate electrode, the device mechanisms proposed for electrolyte-gated organic transistors are unified.

Interchain interactions between π-systems have a strong effect on the properties of conjugated organic materials that find application in devices such as light emitting diodes (OLEDs), organic photovoltaics (OPVs), and field effect transistors (FETs). We have prepared covalently-stacked oligo(1,4-phenylene ethynylene)s and oligo(1,4-phenylene vinylene)s to study the influence of chain-chain interactions on the electronic structure of closely packed conjugated units. These serve as models for segments of conjugated materials in thin film devices. Extension of this concept has allowed us to prepare multi-tiered systems that display the influence of pi-stacking. The stacked architectures were prepared by multi-step synthesis of the scaffolds, followed by metal-catalyzed cross coupling reactions (Sonogashira, Heck, Suzuki couplings) to incorporate the conjugated oligomers. The optical and electrochemical properties of these stacked compounds and polymers were compared to their unstacked linear counterparts. These studies provide a platform for the exploration of the nature of charge carriers and excitons in a broad class of materials that have significant potential in addressing challenges in power generation, lighting and electronics.

Electrochemical Transistor(ECT) was reported by David Nilsson in 2002. Later,its dimensios were specified and a SPICE model was developed. The main purpose of this diploma work is to check the performance of electrochemical transistors in amplifier circuits. Simple amplifier circuits were simulated using SPICE model of ECT. Lateral and Vertical structures of electrochemical transistors were patterned on orgacon sheet(provided by AGFA),with various electrolytes(EG010,MS-HEC &amp; MS-L). Characteric curves and time responses of these transistors were studied and then were then used as an active component in single amplifier circuits. Screen printed ECT's were also checked with the best available electrolyte. Behaviour of self made and screen printed ECT's were compared on the basis of on-off ratio,slew rate,frequency response and gain. Screen printed transistors showed promising results having less deterioration with time  but  till  an  an  input  signal  frequency  of  2Hz  only. Mismatch with simulation results and Shockley's equation were other findings after data analysis. <img src="file:///C:/DOCUME%7E1/zia/LOCALS%7E1/Temp/moz-screenshot.jpg" /><img src="file:///C:/DOCUME%7E1/zia/LOCALS%7E1/Temp/moz-screenshot-1.jpg" />

This thesis presents a comparative study between two silver nanoparticle inks that were deposited using a Drop-on-Demand (DoD) inkjet printer, aiming at finding a functional ink that can be used to print electrodes in Light-emitting Electrochemical Cells (LECs). To achieve this, a DoD inkjet printer was installed and an acquaintance with the printer was attained. Among the two inks, one was employed as received while the other was reformulated, and successful deposition of both the inks was observed. During the reformulation process, it was seen that the highly volatile tetrahydrofuran (THF) solvent can be used to improve the ink properties, in contrast to what is recommended. After that, the inks were deposited on UV-ozone treated glass substrates, sintered at an elevated temperature under ambient conditions, and their specific resistances and thicknesses were measured. Finally, the inks were used to print the anode in a structured sandwich-cell LEC. The performance comparison was conducted by observing the emitted light of the LECs. The results indicate that the reformulated ink performs better, probably due to the lower silver concentration that results in flatter surface, which in turn effectively alleviates shorts.

Despite tremendous achievements, the field of conjugated polymers is still in its infancy, mimicking the more mature inorganic, i.e. silicon-based, technologies. We may though look forward to the realisation of electronic and electrochemical devices with exotic designs and device applications, as our knowledge about the fundamentals of these promising materials grow ever stronger. My own contribution to this development, originating from an idea first put forward by my tutor, Professor Magnus Berggren, is a design for a switchable polymer-based diode. Its architecture is based on a modified version of a recently developed highly-rectifying diode,12 where an intermediate molecular layer has been incorporated in the bottom contact. Due to its unique ability to switch its internal resistance during operation, this thin layer can be used to shift the amount of (forward) current induced into the rectifying structure of the device, and by doing so shift its electrical characteristics between an insulating and a rectifying behaviour (as illustrated below). Such a component should be of great commercial interest in display technologies since it would, at least hypothetically, be able to replace the transistors presently used to address the individual matrix elements. However, although fairly simple in theory, it proved to be quite the challenge to fabricate the device structure. Machinery errors and contact problems aside, several process routes needed to be evaluated and only a small fraction of the batches were successful. In fact, it was not until the very last day that I detected the first indications that the concept might actually work. Hence, several modifications might still be necessary to undertake in order to get the device to work properly.

A high aspect ratio epoxy mask has been built with Taiyo PSR4000BN on chemical sensing array chip. Thickness up to 200 and #61549;m and aspect ratio up to 16:1 have been achieved with this material. It is demonstrated that this material satisfies the mechanical and chemical requirements. A three-electrode system has been designed and built for electrochemistry in micro-cell on chip. Tests with poly(phenylenesulfide-phenyleneamine) (PPSA) demonstrates that it is possible to precisely tune the properties (Work function and resistance) of conducting polymer that has been cast on chip surface. A new test platform GT03 has been fabricated and used to characterize the chemical effects on organic electronics. It is demonstrated that the chemical species in ambient environment can affect organic electronics properties on bulk, interface and electric contact. The contact resistance in organic field-effect transistors (OFETs) has been characterized with modified interdigitated structure (IDS). It is demonstrated that drain and source contact resistances can be calculated separately with modified four-point-probe measurements, and contact resistance and material bulk resistance are actually modulated by the gate electric field. Furthermore, the influence from oxygen doping in poly(3-hexylthiophene) (P3HT) based OFETs has been investigated. A new model of oxygen doping has been suggested and it is demonstrated that oxygen doping can affect all the resistance components in P3HT OFETs.

Perylene-based materials, including charge-transport discotic liquid crystals and charge-transfer long-wavelength absorbing chromophores, for potential organic electronic and optoelectronic applications, were designed, synthesized and characterized. Two types of discotic liquid crystals, perylene diimides and coronene diimides, can form columnar liquid crystalline phases over a wide temperature range; many of them can have room-temperature liquid crystalline phases after cooling from isotropic liquid. Their charge transport properties were studied by space-charge limited current method; high charge carrier mobilities, with the highest being up to 6.6 cm2/Vs, were found in liquid crystalline phases of these materials under ambient conditions. Structural variables, including aromatic cores and side groups, were examined to get a certain degree of understanding of charge transport properties in these discotic liquid crystals. It was found that mesophase order can have an important effect on charge carrier mobilities. The discotic liquid crystals with high charge carrier mobilities are serious candidates for use in large-area low-cost applications such as solar cells. Long-wavelength, highly absorbing chromophores, featuring donor-substituted perylene diimides, were generated by a combination of charge-transfer process and conjugation extension. The charge-transfer chromophores are expected to lead to further investigation on their potentials as sensitizers in Grtzel solar cells.