Photocatalysis is an advanced oxidation process, which has shown to possess an enhanced capability to remove a wide range of contaminants. It involves the use of a semiconductor photocatalyst and a photon source. Photocatalysis has several advantages such as mild reaction conditions like ambient temperature and pressure, good control over the reaction and faster reaction kinetics. Semiconductor photocatalysts such as TiO2, ZnO, Fe2O3, CdS, ZnS, etc. absorbs light of energy greater than or equal to its band gap and the electron in the valence band gets excited to conduction band leaving behind the hole in valence band. These charge carrier pair results in the formation of various reactive oxygen species such as hydroxyl and superoxide radicals which results in the degradation of chemical contaminants and inactivation of microorganisms. TiO2 is the most widely used catalyst in photocatalytic studies because of its high photocatalytic activity, non-toxicity and wide availability. Anatase phase TiO2 has been reported to possess higher photocatalytic activity than the rutile phase. Although there are several methods to synthesize TiO2, solution combustion synthesis is a single step process to produce pure anatase phase TiO2. The catalyst produced by this method has been shown to be superior to the commercially available Degussa P-25 catalyst for the degradation of various chemical contaminants. The present investigation focuses on the use of combustion synthesized catalyst for the inactivation of microorganisms. The photocatalytic activity was compared with commercial Degussa P-25 catalyst. The various aspects of photocatalytic inactivation reactions studied in this dissertation are: i) photocatalytic inactivation of microorganisms in presence of UV light, ii) effect of various parameters on the inactivation, iii) photocatalytic inactivation in presence of visible light, iv) use of immobilized catalyst for the photocatalytic inactivation, v) understanding of mechanism and kinetics of inactivation. Combustion synthesized TiO2 (CS-TiO2), combustion synthesized 1% Ag substituted TiO2 (Ag/TiO2 (Sub)) and 1% Ag impregnated CS-TiO2 (Ag/TiO2 (Imp)) were used as photocatalysts. The catalysts were characterized by powder XRD, TEM, BET surface area, UV-Vis spectroscopy, TGA and photoluminescence spectroscopy. The photocatalytic inactivation experiments were carried out using E. coli (K-12 MG 1655), a bacterial strain and P. pastoris (X-33), a yeast strain, as model microorganisms. The results demonstrate higher photocatalytic activity of all the combustion synthesized catalysts than commercial Degussa P-25 catalyst. The optimum catalyst concentration was 0.25 g/L and the maximum inactivation was observed in the presence of Ag/TiO2 (Imp) catalyst. Rapid and complete inactivation of the microorganisms was observed at lower initial cell concentrations. A reduced photocatalytic inactivation was observed in presence of various anions (HCO3¯ , SO4 2¯ , Cl¯ and NO3¯ ) and cations (Na, K, Caand Mg). Even a small addition of H2O2 was observed to improve the photocatalytic inactivation. At higher dosage of H2O2, a 2 min exposure was sufficient to result in a complete inactivation. Changing the initial pH of the solution was observed to have no significant effect on the photocatalytic inactivation. All the combustion synthesized catalysts showed higher activity as compared to those obtained with commercial Degussa P-25 TiO2 in presence of visible light. The higher photocatalytic activity of combustion synthesized TiO2 can be attributed to the lesser crystallite size, higher surface area, large amount of hydroxyl groups and decreased band-gap energy of the catalyst. The present study demonstrates the potential use of catalyst immobilized thin films for the photocatalytic inactivation of E. coli in the presence of UV light. The CS-TiO2 catalyst was immobilized on glass substrate by LbL deposition technique. The performance of immobilized CS-TiO2 was compared to commercial Degussa Aeroxide TiO2 P-25 (Aeroxide) catalyst. The effect of various operating parameters like catalyst loading, surface area and number of bilayers on inactivation has been investigated. It was observed that increasing the number of bilayers and the concentration did not influence the inactivation but increased surface area led to an increase in inactivation. It was observed that the catalyst immobilized on glass slides can be used for repeated experimental cycles with the same efficiency. It was observed that the inactivation process can be studied in continuous mode by using catalyst immobilized on glass beads. The work also focused attention towards understanding the microorganism inactivation mechanism and kinetic aspects. Various microscopy techniques such as optical microscopy, scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to study the inactivation mechanism. From the images obtained, it was suggested that the inactivation is caused due to rupture of cell wall. The mechanism was also examined by carrying out degradation experiments on cell component such as protein and media component such as dextrose. UV alone was observed to degrade protein and the presence of catalyst showed no additional effect. On the other hand, dextrose does not respond to photocatalytic degradation even at a lower concentration. The photocatalytic degradation of Orange G dye was reduced by addition of dextrose sugar or protein which shows a possibility of competitive degradation. The kinetics of inactivation was studied by various models available in literature such as the power-law model, Chick-Watson model, modified Hom model, GInaFIT tool and a Langmuir-Hinshelwood type model. It was observed that power-law based kinetic model showed good agreement with the experimental data. A mechanistic Langmuir-Hinshelwood type model was also observed to model the inactivation reactions with certain assumptions.

In this study photocatalytic antibacterial and self-cleaning activities of TiO2-SiO2 thin films as a function of TiO2/SiO2 ratios were investigated. TiO2-SiO2 mixed oxides were synthesized by sol-gel method and coated over soda-lime glass plates by dip coating technique. Escherichia coli was used as a model microorganism for the photocatalytic antibacterial tests. Degradation rate of methylene blue (MB) molecules was used to characterize photocatalytic self-cleaning activities of thin film surfaces. The maximum antibacterial activity was achieved over 92 wt% SiO2 containing thin films. However, when the SiO2 content exceeds 92 wt%, photocatalytic antibacterial activity decreased considerably, which was explained by the dilution of TiO2 phase and inaccessibility of TiO2. Increase in photocatalytic antibacterial activity was attributed to increases in the relative surface area, roughness, hydroxyl (OH-) groups and bacterial adhesion. The favored bacterial adhesion enhanced direct contact of bacteria with TiO2 particles and surface reactive oxygen species. The highest initial decomposition rate of MB was obtained for 60 wt% SiO2 and the activity decreases as SiO2 concentration increases. The increase in photocatalytic activity by the SiO2 addition can be explained by the increase of the amount of MB per unit area of TiO2-SiO2 thin films. Different adsorption capability of thin films against MB molecule and E. coli cell was explained as the first reason why the antibacterial and self-cleaning activities reached their maximum values at different SiO2 ratios. The second reason could be related with the different control mechanisms of self-cleaning and antibacterial activities by different textural and surface properties.

This diploma thesis is focused on the study of the effect of ultraviolet radiation and titanium dioxide on the yeast Candida vini. Photocatalytic inactivation of this yeast was performed on various types of titanium dioxide films, which were immobilized on soda lime glasses. Acridine orange was used as a dye to distinguish live and dead yeast cells after certain irradiation time. Live and dead cells emit different light in colour after staining in acridine orange. Candida vini photocatalytic inactivation depends on the amount of titanium dioxide immobilized on glass as well as on the structure of its surface if the lamp intensity remains the same. Kinetics of this photocatalytic process was studied, too.

Water pollution has become an environmental catastrophe due to the rapid urbanization. The treatment of dumping of waste chemicals in water bodies has contributed to the increase in pollution. In addition to the pollution caused by waste chemicals, faecal bacteria such as Escherichia, Staphylococcus, Pseudomonas etc., can cause serious health issues. Techniques such as filtration and chlorination provide clean water but are associated with disadvantages such as toxic by-products. Although clean water can be still obtained by these techniques, the development of resistance by microorganisms with such conventional treatments of antibiotics is inevitable and poses a new threat. Various researches have taken place in the past few decades to provide clean drinking water. Photocatalysis is considered to be a promising viable alternative for the existing methods to solve the menace of water pollution. It is an advanced oxidation process where the reactive oxygen species are generated by using nanomaterials that can cause degradation of chemicals and pathogens. Particularly, photocatalysis using semiconductors and their composites have been tested for their use in the destruction of contaminants. Several methods have been used in the synthesis of nanomaterials and the variations in their morphologies have resulted in different applications such as photocatalysis and electrocatalysis. Among all semiconductors, TiO2 has been widely used in this application owing to their non-toxicity and abundance in availability. However, TiO2 can be activated only in the presence of UV light. Therefore, the formation of heterojunctions, doping of metals/no- metals in TiO2 has enabled the activation of TiO2 in the visible region. The former approach has also been studied with ceria and silver salts combination. Besides conventional metal oxides, other transitional metal oxides such as copper oxide and bismuth oxide have also been studied owing to its conducting property and facile growth on substrates respectively for enhanced photocatalysis. All the above tweaking has enabled efficient charge separation, band gap reduction, and prevention of recombination. In this thesis, all the nanomaterials and their composites have been synthesized using simple methods such as solution combustion, hydrothermal, solution co-precipitation, and chemical deposition. The primary aim of this thesis is to synthesize various effective nanomaterials with different morphologies, bandgap engineered nanocomposites, metal or non-metal doped metal oxides for efficient waste water treatment of dyes, antibiotics, phenols, and bacteria. Besides, relying on photocatalytic ability, the photoconductivity and intrinsic conducting properties of nanomaterials were exploited to perform photoelectrocatalysis that enhances the rate of decontamination to several orders than photocatalysis. In addition to focusing on increasing the rate of degradation, the main drawback of photocatalysis which is catalyst retrieval has been overcome using conducting substrates and nanomaterial coated substrates for efficient photocatalytic and photoelectrocatalytic decontamination of waste water. All the structural, morphological, chemical and optical properties were thoroughly studied using various characterization techniques such as XRD, SEM, TEM, XPS, UV-DRS, PL respectively. The rate kinetics of dye, antibiotic and phenol degradation was examined. Experimental data was tested with the proposed model in the case of photoelectrocatalytic degradation. The photocatalysts were also studied for its reusability for many cycles. All the proposed works have analyzed the reason for the enhanced activity by performing scavenger reactions to determine the responsible reactive oxygen species. Thus, this thesis exhibits a thorough understanding of how to design and engineer nanomaterials for photocatalytic and photoelectrocatalytic water remediation. The following are the chapters discussed in this thesis. Chapter 1 discusses the drawbacks associated with the current waste water treatment methods and the possibilities of photocatalysis to replace the existing treatments. The advantages of certain transition metals, conventional methods of synthesis and various other properties of the nanomaterials have been discussed. Chapter 2 explains the synthesis of TiO2 nanobelts using combustion synthesized TiO2 under UV and solar irradiation. The catalyst has been characterized for its structural, morphological, chemical and optical properties. The degradation of anionic and cationic dyes and their activity against E.coli bacteria have been evaluated. The efficiency of this catalyst has been compared with commercial Degussa P25. This study shows the morphological influence of nanomaterials on photocatalytic activity. Chapter 3 describes the synthesis of Ag3PO4 impregnated combustion synthesized TiO2 nanobelts using co-precipitation technique. The activity of this material has been studied under solar light. The catalyst has been characterized for its structural, morphological, chemical and optical properties. Similar to the previous chapter, the degradation of dyes and the antibacterial activity of this catalyst has been compared with commercial Degussa P25. This study explains the importance of morphology and charge carrier facilitation in the case of heterojunction formation. Chapter 4 explains the synthesis of ceria nanoflakes by solution combustion method using ascorbic acid as fuel and PEG assisted sonochemical method. The catalyst has been characterized for its structural, morphological, chemical and optical properties. The effect of silver salts such as AgBr on ceria/Ag3PO4 under visible region for degradation of dyes and antibacterial activity has been evaluated. This work elucidates the effect of band engineering in the charge carrier dynamics between interfaces of components within the catalysts. Chapter 5 elucidates the synthesis of vanadium, nitrogen co doped TiO2 catalysts for the simultaneous degradation of microbes and antibiotics. The primary aim of this work is to understand whether interstitial or substituted doped nitrogen will be effective in the presence of vanadium. The photoactivity of this novel catalyst was studied for its synergistic degradation of antibiotics and bacteria simultaneously towards the prevention of microbial resistance towards antibiotics. Chloramphenicol and E.coli were subjected to photodegradation under visible light. Chapter 6 explains the synthesis of copper oxide based nanomaterial for antibiotic and bacterial degradation by photoelectrocatalysis. In order to enhance the rate of photodegradation, photocatalysis has been upgraded with the application of a potential to photocatalytic systems that possess better charge conducting capability. Highly network like copper oxide has been synthesized using conventional combustion synthesis method and compared with copper oxide nanorods synthesized by hydrothermal method. The rate kinetics of photocatalytic and photoelectrocatalytic degradation of antibiotics has been examined thoroughly and validated based on a cyclic network model. This work demonstrates the synergistic rate enhancing capacity upon combining photocatalysis and electrocatalysis. Chapter 7 discusses the fabrication of Cu/CuO/FTO (fluorine doped tin oxide) based substrates for bacterial degradation. Considering the difficulties in photocatalyst retrieval processes and realizing the importance of electrocatalysis, conducting substrates such as Cu strip, FTO were subjected to antibacterial treatment. Formation of copper oxide onto copper strip during the course of reaction forced us to develop CuO/Cu and CuO/FTO interfaces to examine the photocatalytic and photoelectrocatalytic killing of E.coli. Chapter 8 investigates the fabrication of Bi2O3/Ag based material for photocatalytic and photoelectrocatalytic degradation for phenols and substituted phenols. This work starts with fabrication of Bi2O3 working electrodes by chemical deposition. Photodegradation experiments were conducted under UV irradiation and enhancement of the rate of degradation was observed when the working electrode was deposited with silver nanoparticles via chemical reduction method. Formation of the intermediate Bi(OH)x on Bi2O3 or Bi2O3/Ag has resulted in better hydroxyl radical generation upon excitation. Similarly, surface plasmon resonance due to silver nanoparticles was found to be responsible for augmentation in degradation efficiency of phenol. Chapter 9 briefly summarizes the work and provides future directions. The research work thus attempts to design and engineer photocatalytic nanomaterials that are better than the existing materials and emphasizes the importance towards water remediation.