Thesis advisor: Udayan Mohanty / Among the existing strategies to direct solar energy harvesting and storage, solar fuel production by photoelectrocatalysis promises a comparatively simple, low-cost route. The science behind this process is straightforward: stable semiconductors absorb sunlight and use the energy to excite charges, which then drive redox reactions at the surface. Careful studies of the photoelectrode surface provide important considerations in building a high-performance photoelectrode. Specifically, I focused on controlling the surface band alignment of Cu2O photocathode|water for hydrogen evolution reaction. A ZnS buried heterojunction is formed to improve the photovoltage. Then I focused on understanding the influence of chemical species on surface kinetics and energetics for water oxidation reaction. Two hematite photoanodes with preferably exposed {001} and {012} facets were examined. Further, I systematically studied three different types of surfaces, bare hematite, hematite with a heterogenized Ir water oxidation catalyst (WOC), and a heterogeneous IrOx WOC. While both WOCs improve the performance of hematite by a large margin, their working mechanisms are found to be fundamentally different. I also focused on utilizing surface photoexcited species to control product selectivity. Selective CO production by photoelectrochemical methane oxidation is successfully demonstrated. Detailed experimental investigations revealed that a synergistic effect by adjacent Ti3+ sites is the key to CO formation. / Thesis (PhD) — Boston College, 2018. / Submitted to: Boston College. Graduate School of Arts and Sciences. / Discipline: Chemistry.

One way of harnessing and storing our most abundant and renewable energy source, sunlight, is by utilizing it to split water for the hydrogen generation as a storable form of fuel. Si, the most investigated material for solar-to-hydrogen technology has great potential as the single photoelectrode. While some success has been achieved in Si-Based photoelectrochemical (PEC) systems, they suffer from low efficiency and short longevity. Moreover, in order for hydrogen to be commercially viable, the existing challenges of electrical, optical, and catalysis management must be addressed concurrently. Herein, we work on the simultaneous improvement in light harvesting, charge carrier separation/transfer, and catalysis management of Si-based photocathodes, achieving best-in-class efficiency with stable electrochemical performance. By decoupling the light harvesting side from the electrocatalytic surface we nullify parasitic light absorption. We developed a Si bifacial (SiBF) PEC photocathode to absorb light on both sides of PEC devices, which exhibits a current density of 39.01 mA/cm2. Unlike conventional monofacial PEC cells, our bifacial design demonstrates excellent omnidirectional light harvesting capability. Furthermore, back buried junction photoelectrochemical (BBJ-PEC) cells were fabricated that can realize efficient decoupling of photon. This scheme enables maximum light-harvesting without any metal contact, which prevents the shadow effect during the water splitting reaction. The highest hydrogen evolution current density (41.76 mA/cm2) was demonstrated based on a single BBJ-PEC device. Additionally, wireless water splitting can be achieved when three BBJ-PEC cells were connected in series. The efficient PEC cell design described herein demonstrates promising performance, taking us a step closer to real-world solar-to-hydrogen production.

Ce mémoire vise à montrer l’intérêt de nanoparticules (NPs) de TiO2 comme plateforme pour immobiliser dans un environnement proche des complexes de coordination pouvant interagir par transfert d’électron photoinduit. Nous nous sommes intéressés à l’étude de nanomatériaux hybrides associant le complexe [Ru(bpy)3]2+ (bpy = 2,2'-bipyridine) comme photosensibilisateur aux complexes [Cr(ttpy)2]3+ ou [Mn(ttpy)(CO)3Br] (ttpy = 4'-(p-tolyl)-2,2':6',2''-terpyridine) comme accepteurs d'électrons. Pour immobiliser les différents complexes à la surface du TiO2, une fonction acide phosphonique a été introduite sur une des bipyridines du centre [Ru(bpy)3]2+ et sur la terpyridine des complexes [Cr(ttpy)2]3+. L’étude des processus de transferts de charges photo-induits sous irradiation en lumière visible sur le colloïde TiO2/RuII montre que l'état à charges séparées (e-)TiO2/ RuIII possède une longue durée de vie, ce qui rend possible l'utilisation des charges dans des réactions successives d’oxydation ou de réduction. Notamment l’irradiation du colloïde TiO2/RuII en présence de [Cr(ttpy)2]3+ et de triéthanolamine (TEOA) comme donneur d'électron sacrificiel permet la réduction à deux électrons du [Cr(ttpy)2]3+. Par la suite, le complexe [Cr(ttpy)2]3+ est immobilisé sur les NPs de TiO2/RuII pour former un assemblage RuII/TiO2/CrIII au sein duquel les processus de transfert d'électrons photo-induits sont étudiés. De manière à proposer un système pour la réduction photocatalytique du CO2, le complexe [Mn(ttpy)(CO)3Br] a été co-immobilisé avec le [Ru(bpy)3]2+ suivant une approche de chimie sur surface pour former le colloïde RuII/TiO2/MnI. Ce système présente une excellente sélectivité vis-à-vis du HCOOH comme seul produit de la photoréduction du CO2 en présence de 1-benzyl-1,4-dihydronicotinamide (BNAH) comme donneur d'électron sacrificiel. Un système hybride associant le [Ru(bpy)3]2+ portant des fonctions pyrroles et immobilisé sur TiO2 a également été synthétisé et étudié. Sous irradiation lumineuse, le transfert de charges (e-)TiO2/[Ru-pyr]3+ permet d’induire la polymérisation du pyrrole. Le nanocomposite TiO2/poly(Ru-pyr) obtenu et déposé sur une électrode génère, en présence de TEOA, un photocourant anodique stable de plus de 10 μA.cm-2. L’ensemble des résultats montre que les NPs de TiO2 peuvent être un moyen d’assembler des complexes dans un environnement proche en limitant les interactions à l’état fondamental, mais permettant des transferts d’électrons photoinduits entre eux. Suivant les potentiels redox des différents composants, les transferts d’électron ont lieu soit via la nanoparticule soit en surface de celle-ci. / This thesis aims to investigate the possibility of using TiO2 nanoparticles (NPs) as a platform to immobilize proximal coordination complexes that can interact with each other by photoinduced electron transfer. We have studied hybrid nanomaterials combining [Ru(bpy)3]2+ (bpy = 2,2'-bipyridine) as a photosensitizer and [Cr(ttpy)2]3+ or [Mn(ttpy)(CO)3Br (ttpy = 4'-(p-tolyl)-2,2':6',2''-terpyridine) as electron acceptors. To immobilize the various complexes on the surface of TiO2, a phosphonic acid functional group was introduced on one of the bipyridines of the [Ru(bpy)3]2+ center and on the terpyridines of the [Cr(ttpy)2]3+ complex. Under visible light, the TiO2/RuII colloid undergoes a photo-induced charge transfer process leading to a long-lived charge separation state (e )TiO2/RuIII, which makes it possible to be engaged in successive oxidation or reduction reactions. In particular, the visible irradiation of the TiO2/RuII colloid in the presence of [Cr(ttpy)2]3+ and triethanolamine (TEOA) as a sacrificial electron donor allows the two-electron reduction of [Cr(ttpy)2]3+. Subsequently, the [Cr(ttpy)2]3+ complex has been immobilized on the TiO2/RuII NPs to form a RuII/TiO2/CrIII assembly in which the photoinduced electron transfer processes were investigated. In order to propose a system for the photocatalytic reduction of CO2, the [Mn(ttpy)(CO)3Br] and [Ru(bpy)3]2+ complexes were co-immobilized on TiO2 NPs following a chemistry on surface approach to form a RuII/TiO2/MnI triad. Under irradiation at 470 nm, this system exhibits excellent selectivity towards HCOOH as the only product of CO2 photoreduction in DMF/TEOA solvent mixture, in the presence of 1-benzyl-1,4-dihydronicotinamide (BNAH) as a sacrificial electron donor. Another hybrid system linking a [Ru(bpy)3]2+ unit to two pyrrole functions and being immobilized on TiO2 has also been synthesized and studied. Under visible light, the transient (e-)TiO2/[Ru-pyr]3+ species induce the polymerization of pyrrole to form a TiO2/poly(Ru-pyr) nanocomposite. The nanocomposite deposited on an electrode generates, in the presence of TEOA, a stable anodic photocurrent of more than 10 μA.cm-2. All the results show that TiO2 NPs can be used to associate different complexes in a close environment by limiting the interactions in the ground state but allow photoinduced electron transfer processes between them. Depending on the redox potentials of the different components, the electron transfer takes place either through the semiconducting NPs or on the surface.

Trois types des ETLs ont été développés et étudiés dans cette travaille comme une photoélectrode dans la cellule solaire à colorant (DSSC). Ils sont composés de (1) deux types de nanoparticules de TiO2-brookite, (2) le composite d'anatase et graphène et (3) la nanoparticule de ZnO qui a nanobâtonnet structure, respectivement. Toutes photoélectrodes sont préparées par le technique « doctor blade ». La morphologie des photoélectrodes ont été caractérisées par microscopie électronique à transmission (MET) et microscopie électronique à balayage (MEB). Les épaisseurs de couche sont mesurées en utilisant la profilométrie. Pour les films caractérisations structurelles, une haute résolution diffractomètre à rayons X a été utilisée. La spectroscopie infrarouge à transformée de Fourier (FTIR) et micro-Raman ont été effectués pour vérifier la préparation composite TiO2_Gr. Les propriétés des films optiques ont été enregistrées avec un spectrophotomètre équipé d'une sphère d'intégration de techniques. Les performances de cellules ont été obtenues en mesurant les courbes IV des cellules sous illumination calibré. Pour atteindre une compréhension profonde du fonctionnement de la cellule, la spectroscopie d'impédance (IS) technique a été étudiée sur une grande gamme de potentiel appliquée. En faisant est l'étude, la structure électronique, porteurs de charge à vie (tn), le transport / heure de collecte (ttr) et les paramètres de transport d'électrons des couches ont été déterminées. L'étude soin de leurs propriétés a révélé non seulement leurs avantages mais aussi leur limitation. Cette information sera bénéfique comme une considération pour les travaux futurs. / Three kinds of ETL have been developed and studied in this present work as a photoelectrode in DSSC. Those composed of (1) two kinds of TiO2-brookite nanoparticles, (TiO2_B1 and TiO2_B2), (2) the composite of anatase and graphene (TiO2_Gr) and (3) the nanorods like ZnO nanoparticles (ZnO_NR), respectively. All photoelectrode are prepared by doctor blading technique. The morphology of photoelectrodes have been characterized using transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The layer thicknesses were measured using profilometry. For the film structural characterizations, a high-resolution X-ray diffractometer was used. The Fourier transform infrared (FTIR) and micro Raman measurement have been carried out to verify the TiO2_Gr composite preparation. The optical film properties (total transmission and total reflection) were recorded with a spectrophotometer equipped with an integrating sphere techniques. The cell performances were obtained by measuring the I-V curves of the cells under calibrated illumination. To achieve an in-deep understanding of the cell functioning, the impedance spectroscopy (IS) technique has been studied over a large applied potential range. By doing IS study, the electronic structure, charge carrier lifetime (tn), transport/collection time (ttr) and electron transport parameters of the layers have been determined. The carefully study of their properties has revealed not only their advantages but also their limitation. This information will be beneficial as a consideration for the future work.

Solar energy is the most abundant efficient and important source of renewable energy. The objective of this study is to develop highly efficient visible light responsive photocatalysts for overall water splitting. This is done by using silver or copper containing materials. Phosphate compounds have caught much attention due to their rigid structure, thermal stability and resistance to chemical attacks. Solid phosphates can be prepared by direct solid-state reaction between metal cations and phosphate anions at high temperatures. Double metal phosphates of the Nasion-type structure had shown further technological importance. It has been reported that well-crystallized double metal phosphate particles have excellent ordering and cationic conduction channels in the Nasicon framework. In this study, several Nasion-type structured materials have been synthesized by solid-state method (e.g. CuTi2(PO4)3 and AgTi2(PO4)3) heated up under different temperatures (400–1100C) in N2 or air atmosphere. These materials were characterized by XRD, SEM, DR-UV-Vis spectroscopy and tested for photocatalytic applications. A new method for direct synthesis of photoelectrode on Ti Plate had been demonstrated. Further investigations on controlling the size and morphology for better performance of single and double metal phosphates will be done.

Due to the drastic required thermodynamical requirements, a photoelectrode material that can function as both a photocathode and a photoanode remains elusive. In this work, we demonstrate for the first time that, under simulated solar light and without co-catalysts, donor-acceptor conjugated acetylenic polymers (CAPs) exhibit both impressive oxygen evolution (OER) and hydrogen evolution (HER) photocurrents in alkaline and neutral medium, respectively. In particular, poly(2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine) (pTET) provides a benchmark OER photocurrent density of ~200 μA cm−2 at 1.23 V vs. reversible hydrogen electrode (RHE) at pH 13 and a remarkable HER photocurrent density of ~190 μA cm−2 at 0.3 V vs. RHE at pH 6.8. By combining theoretical investigations and electrochemical-operando Resonance Raman spectroscopy, we show that the OER proceeds with two different mechanisms, with the electron-depleted triple bonds acting as single-site OER in combination with the C4-C5 atoms of the phenyl rings as dual sites. The HER, instead, occurs via an electron transfer from the tri-acetylenic linkages to the triazine rings, which act as the HER active sites. This work represents a novel application of organic-based materials and contributes to the development of high-performance photoelectrochemical catalysts for the solar fuels’ generation.