No description available.

This thesis is concerned with furthering our understanding of the basis of visible region photocatalytic activity exhibited by doped TiO2-based materials. A range of experimental techniques including high resolution X-ray photoemission spectroscopy and diffuse reflectance spectroscopy are used to investigate electronic structure and an attempt is made to link these results to the observed photocatalytic activity. Both anionic (N) and cationic (Rh and Sn) dopants are investigated. [See pdf file for full abstract].

<p>A fundamental understanding of heterogeneous catalysis requires analysis of model catalytic surfaces in tandem with complex technical catalysts. This work was divided in three areas, 1- preparation and characterization of model surfaces synthesized by vapor deposition techniques, 2- kinetic evaluation of model catalysts for formic acid decomposition and dry methane reforming, 3- characterization and kinetic evaluation of technical catalysts for the water gas shift reaction.</p> <p>In the first project, model PdZn intermetallic surfaces, a relevant catalyst for propane dehydrogenation, were prepared using an ALD approach. In this work, model surfaces were synthesized by exposing Pd(111) and Pd(100) surfaces to diethylzinc at ca. 10^-6mbar. Several different surface structures were identified by careful control of the deposition temperature of the substrate. Modifications in the adsorption properties of these surfaces towards carbon monoxide and propylene coincided with the structure of the PdZn surface layer. </p> <p>In the second project, formic acid decomposition kinetics were evaluated on model Pt catalysts. Formic acid decomposition was found to be structure-insensitive on Pt(111), Pt(100), and a polycrystalline foil under standard reaction conditions. CO selectivity remained < 1% for conversions <10%. Additionally, inverse Pd-Zr model catalysts were prepared by ALD of zirconium-t-butoxide (ZTB). Depending on treatment conditions, either ZrO_xH_y or ZrO₂ overlayers or Zr as sub-nanometer clusters could be obtained. The activity of the model catalyst surface towards dry reforming of methane if the initial state of the zirconium is metallic. </p> <p>In the third project, Au/Fe₃O₄ heterodimer catalysts were characterized for their thermal stability. In-situ TEM and XPS characterization demonstrates that the gold nanoparticles transform into gold thin films that wet the Fe₃O₄ surface as the reduction of the oxide proceeds. DFT calculations show that the adhesion energy between the Au film is increased on a partially reduced Fe₃O₄ surface. Additionally, Pt/Nb₂CT_x catalysts were characterized and kinetics evaluated for the water gas shift reaction. XPS and TEM characterization indicates that a Pt-Nb surface alloy is formed under moderate reduction temperatures, 350^OC. Water-gas shift reaction kinetics reveal that the alloy-MXene interface exhibit high H₂O activation ability compared to a non-reducible support or bulk niobium carbide. </p>

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / A espectroscopia de fotoelétrons excitados por radiação ultravioleta (UPS Ultraviolet Photoelectron Spectroscopy) é uma técnica de análise tipicamente de superfícies, particularmente relevante para estudos onde se deseja obter informações sobre os níveis de valência de átomos situados na superfície de um material. Esta técnica tem importantes aplicações em áreas em que reações de superfícies são fundamentais, como, por exemplo, estudos de corrosão, oxidação e de catálise. Neste trabalho, descreve-se a implantação de UPS no Laboratório de Física Aplicada do Centro de Desenvolvimento da Tecnologia Nuclear LFA/CDTN. Para a produção de fótons na região do ultravioleta é utilizada uma lâmpada de He, que emite fótons com energias de 40,8 e 21,2 eV. Essa instrumentação, construída em nosso laboratório, foi instalada em uma câmara de ultra-alto vácuo (UHV) e testada em medidas da banda de valência de monocristais. Para comprovar a funcionalidade da técnica, testes foram conduzidos em monocristais de Cu (100), Cu90Au10 (100) e Cu3Au (100), sendo que os resultados aqui apresentados, mostram o bom desempenho da instrumentação desenvolvida. A oxidação in-situ, em UHV, de filmes finos de Ni foi também investigada por XPS (XRay Photoelectron Spectroscopy), na tentativa de se observar a influência da pressão parcial de oxigênio e da temperatura na preparação de bicamadas Ni/NiO por oxidação in-situ. Nossos resultados mostram que para exposição do Ni a 103 L de O2 a temperaturas de até 523 K ocorre a formação de no máximo 10 Å de óxidos de níquel. / The Ultraviolet Photoelectron Spectroscopy (UPS) is an important surface analysis technique used in surface valence band studies. This technique has been applied to fundamental research on areas like corrosion, oxidation, and catalysis. In this work, a He lamp for UPS was constructed, installed and tested in the Laboratório de Física Aplicada at Centro de Desenvolvimento da Tecnologia Nuclear LFA/CDTN. The Helium discharge lamp has photon emission of 40,8 eV and 21,2 eV energy. The instrumentation built in our laboratory was installed in an Ultra High Vacuum (UHV) chamber and the obtained UPS results confirm the good perfomace of the instrument. The surface analysis tests were carried out on Cu (100), Cu90Au10 (100) and Cu3Au (100) surfaces. Furthermore, the preparation of NiO/Ni bilayer by in-situ oxidation of nickel films was also investigated by X-Ray Photoelectron Spectroscopy (XPS). The influence of oxygen partial pressure and the temperature changes in the growth of NiO during the in-situ oxidation of Ni were studied. For Ni exposure to 103 L O2 from room temperature up to 523 K, we observe the formation of, at most, 10 Å Ni oxides.

Novel photovoltaic cells receive considerable attention from researchers as evidenced by high numbers of published articles. Different types of materials are currently being examined in order to reduce the cost and improve the efficiency of solar cells. Essentially, solar cells are constructed by placing layers of light absorber between electron and hole transport materials. Electricity generation by solar cells involves multiple processes. These processes require an understanding of the physical properties of the surfaces and interfaces of the materials. In this thesis, materials for novel photovoltaic cells are studied by X ray photoelectron spectroscopy (XPS), a surface and interface characterisation technique. The materials studied in this thesis are colloidal quantum dots (CQDs) of the core/shell systems CdTe/CdSe and PbS/CdS, and CQDs that have been surface passivated using Cl- (CdTe/Cl) and CdS (CdTe/CdSe/CdS and PbS/CdS). Moreover, CsSnI3, a perovskite material, is also studied in both bulk and thin film form. CQDs can be used as light absorbers in solar cells while CsSnI3 can be employed as the hole transport material. The role of the core shell structure and surface passivation treatment is to improve or maintain charge transport as well as acting as a protective layer to the CQDs. Depth profiling synchrotron radiation XPS is used to determine these structures. In the CdTe/CdSe samples, the elemental ratio between Se (shell) and Te (core) increases with decreasing sampling depth, demonstrating the presence of a CdSe shell located at the surface of the CQDs. The shell thicknesses of the core-shell systems are estimated from XPS and show that the addition of the third thin shell (of CdS) protects the CQD during ligand exchange. Cl- passivation is shown to reduce the energy the valence band maximum and the energy gap of CdTe CQDs. This is associated with the passivation of midgap trap states due to the removal of dangling bonds at the surface of CQDs. Surface passivation is shown to improve the stability of CQDs to air exposure. This is indicated by a significant reduction of the surface oxide species in the passivated PbS/CdS samples. In the unpassivated core-only PbS samples, however, oxidation rapidly occurs which affects the electronic states required for charge transport in solar cells. XPS studies of CsSnI3 show that this material is reactive to air exposure. Surface preparation techniques are performed to remove the contamination layer and reveal the physical properties of the perovskite itself. This is confirmed by the elemental ratios from XPS. The metallic character of CsSnI3 is also observed in the valence band spectra as evidenced by the appearance of the Fermi edge.

<p>In dye-sensitized solar cells, the functions of light absorption and charge transport are separated. A photosensitive ruthenium-polypyridine dye in the cell absorbs light, injects an electron to a semiconductor and is then regenerated by a redox couple, typically iodide/triiodide. Quantum chemical calculations of the electronic structure of triiodide have been carried out with the restricted active space SCF method, including spin-orbit coupling, and with density functional theory. It was shown that the difference in charge density between the terminal and central atoms results in a splitting of the core levels. The calculations gave a value of the splitting of 0.8 - 1.0 eV for the <em>3d</em> and <em>4d</em> levels. Experimentally, the electronic structure has been investigated with photoelectronspectroscopy. The measured terminal/center splitting is 1.1 eV.The spin-orbit interaction of the <em>4d </em>levels of triiodide has also been calculated. The splitting was determined to be 1.6 eV. The experimental value is 1.7 eV. An assignment of the peaks in the computed spectrum of triiodide was made and the features of the experimental spectrum have beenidentied.The theoretical valence spectrum of triiodide has been computed and assigned. The results can be used in the analysis of photoelectron spectra of the molecule. Information about the electronic structure of the redox couple can help in the understanding of the electron transfer processes and forfurther development of the solar cells.  Furthermore, the solvation structure of the prototype dye, the tris(bipyridine)ruthenium(II) complex, in water and its interaction with iodide and chloride has been studied by means of molecular dynamics simulations. The trajectory analysis showed that the water molecules in the first solvation shell form a chain in between the bipyridine ligands. It was found that the iodide ions are more likely than chloride to enter between the ligands, which can be important for the electron transfer processin the solar cell.</p>

<p>Recently, materials such as hole conductors (CuI, CuSCN) and light absorbers (Ru-complexes, CuInS₂) have been actively investigated for application in nanocrystalline solar cells. In this thesis combinations of these materials have been studied.</p><p>In the first part of the thesis, various methods were applied to characterize the electronic structure and photoconversion mechanism of the dye molecule Ru(dcbpyH₂)₂(NCS)₂ when combined with materials for the use in photovoltaic devices. Specifically, the adsorption and electronic structure of the dye molecules adsorbed to semiconductors were investigated by means of photoelectron spectroscopy. The results indicate a chemical bond between the dye molecules and the hole conductors (CuI, CuSCN) via the NCS- groups. In addition, preparation of a TiO₂/Ru-dye/CuI solid state model system was studied <i>in situ</i>. These experiments showed a partial breaking of the TiO₂-dye bond caused by CuI evaporation. Photovoltage measurements were also performed. These investigations showed a shift in the light absorption threshold of the dye molecules adsorbed onto the hole conductors (CuI and CuSCN), indicating new defect states at the dye/CuSCN interface. Also, charge accumulation and transport in solar cells with CuSCN were compared to liquid electrolyte cells. Measurements showed that the lifetime and transport time of electrons in solar cells with CuSCN are much shorter than in electrolyte cells.</p><p>In the second part of the thesis, the deposition of CuInS₂ onto various metal oxides by spray pyrolysis has been studied with x-ray diffraction and photoelectron spectroscopy. The measurements showed that the morphologies of the substrates play a significant role in the formation of CuInS₂ layers. Also, the presence of CdS at TiO₂ has a positive influence on the formation of CuInS₂.</p>

<p>Li-ion batteries are not only a technology for the future, they are indeed already the technology of choice for today’s mobile phones, laptops and cordless power tools. Their ability to provide high energy densities inexpensively and in a way which conforms to modern environmental standards is constantly opening up new markets for these batteries. To be able to maintain this trend, it is imperative that all issues which relate safety to performance be studied in the greatest detail. The surface chemistry of the electrode-electrolyte interfaces is intrinsically crucial to Li-ion battery performance and safety. Unfortunately, the reactions occurring at these interfaces are still poorly understood. The aim of this thesis is therefore to increase our understanding of the surface chemistries and stability phenomena at the electrode-electrolyte interfaces for three novel Li-ion battery electrode materials.</p><p>Photoelectron spectroscopy has been used to study the surface chemistry of the anode material AlSb and the cathode materials LiFePO₄ and Li₂FeSiO₄. The cathode materials were both carbon-coated to improve inter-particle contact. The surface chemistry of these electrodes has been investigated in relation to their electrochemical performance and X-ray diffraction obtained structural results. Surface film formation and degradation reactions are also discussed.</p><p>For AlSb, it has been shown that most of the surface layer deposition occurs between 0.50 and 0.01 V <i>vs.</i> Li°/Li⁺ and that cycling performance improves when the lower cut-off potential of 0.50 V is used instead of 0.01 V. For both LiFePO₄ and Li₂FeSiO₄, the surface layer has been found to be very thin and does not provide complete surface coverage. Li₂CO₃ was also found on the surface of Li₂FeSiO₄ on exposure to air; this was found to disappear from the surface in a PC-based electrolyte. These results combine to give the promise of good long-term cycling with increased performance and safety for all three electrode materials studied.</p>

Given the wide range of properties and applications of intermetallic compounds, it is important to achieve a detailed understanding of their structure and bonding. X-ray photoelectron spectroscopy (XPS) and X-ray absorption near-edge spectroscopy (XANES) were used to study the electronic structure of several types of pnictides (compounds containing Pn = P, As). ZrAs2, forming a PbCl2-type structure, has been established to be a genuine binary phase that is strictly stoichiometric. At 900 °C, it supports extensive solubility of Ge to form the ternary extension Zr(GexAs1−x)As (0 ≤ x ≤ 0.4). XPS analysis and band structure calculations confirmed that the Ge and As atoms are anionic in character and that the substitution of Ge for As is driven by a depopulation of anion–anion antibonding states. ZrCuSiPn and REMAsO are important representatives of ZrCuSiAs-type materials. The small magnitudes of the binding energy shifts in the XPS spectra of ZrCuSiPn suggest significant covalent character in the Zr–Si, Zr–Pn, and Cu–Pn bonds, consistent with a three-dimensional structure. On progressing from ZrCuSiP to ZrCuSiAs, the charge transfer from metal to Pn atoms becomes less pronounced, as indicated by changes in the intensity of the Cu K-edge and Zr K, L-edge XANES spectra. Binding energy shifts and satellite features of the XPS spectra of REMAsO indicated that bonding in the [REO] layer is ionic, whereas bonding in the [MAs] layer is strongly covalent. Altering the electronic structure of one layer (by M or RE substitution) does not affect the electronic structure of the other layer, consistent with a two-dimensional structure in REMAsO. Metal-rich phosphides M2P (forming Cr2P-, Fe2P-, and Co2P-type structures) and M3P (forming Ni3P-type structures) were examined by XPS and XANES. The P 2p3/2 binding and P K-edge absorption energies decrease with greater ionic character of the M−P bonding and indicate the presence of anionic phosphorus. Interatomic effects play a more important role in affecting the energy shifts in these metal-rich phosphides than in the monophosphides, becoming more pronounced with higher metal concentration. Surprisingly, intraatomic effects dominate in mixed-metal phosphides (Ni1-xMx)2P despite evidence of metal-to-metal charge transfer from the Ni XANES spectra and Ni 2p XPS satellite features.

The main objective for the work described in this PhD thesiswas to formulate a friction model to characterize thefrictional behavior of paper. More specifically, the modelshould explain a phenomenon that is typical for paper grades,viz.: that the level of paper-to-paper friction is dependent onthe direction and the number of previous slides. The modelshould also explain the lubricating effect oflow-molecular-mass lipophilic compounds (LLC) that occur inpaper on paper-to-paper friction. Furthermore, the model shoulddescribe the types of forces that influence paper-to-paperfiction and explain the mechanism by which the LLC decreasepaper-to-paper friction. This thesis consists of a literature review of the basicconcepts of tribology and a summary of the main results andconclusions from four studies on the frictional characteristicsof paper and a study on the friction and adhesion of cellulosesurfaces together with some unpublished material. The purpose of the investigation described in the firstpaper was to explain a phenomenon that is typical for papergrades, viz.: the level of paper-to-paper friction is dependenton the direction and the number of previous slides. Thisbehavior is called“friction hysteresis”by theauthors, and it has its origin in the reorientation of thefibers on the surface of a paper and their alignment relativeto the sliding direction. The second paper describes a study that was aimed atidentifying lubricants that occur natively in paper. Filterpapers were impregnated with model compounds representing woodextractives, i.e. low-molecular-weight lipophilic compounds,which are present in wood, pulp and paper, and thepaper-to-paper friction was determined. The results of thatstudy show that a wood extractive must fulfill severalstructural criteria in order to lubricate a paper surface: Itmust have a hydrophilic group that can attach to the papersurface and a linear hydrocarbon backbone of sufficientlength. Although it is not specifically stated in the second paper,the authors proposed a type of lubrication by which woodextractives decrease paper-to-paper friction that is, ineffect, boundary lubrication. The purpose of the investigationdescribed in the third paper was to clarify whether woodextractives and other low-molecular-mass lipophilic compoundsthat occur in paper can act as boundary lubricants on papersurfaces. The main objective of that study was to investigatethe role of chemical structure of LLC for their orientationrelative to the paper surface, which is an important criterionfor boundary lubrication. Filter papers were impregnated withmagnesium salts of different lipophilic acids, which were usedfor model compounds for the LLC. The deposited layers ofmagnesium salts were characterized by X-ray photoelectronspectroscopy (XPS) and contact angle goniometry and thefriction of the impregnated paper sheets was determined. Theresults show that the degree of lubrication and the resistanceto wear of the layers of a magnesium salt increased withincreasing chain length and increasing degree of linearity ofthe lipophilic acid. Based on the results of that study and ofearlier studies, it is concluded that boundary lubrication isthe type of lubrication by which low-molecular-mass lipophiliccompounds that occur natively in paper decreasepaper-to-paper-friction. In boundary lubrication, surfaces are covered withmonolayers of lubricant molecules that comprise an active headgroup that can attach to the surface, e.g. a carboxyl group,and an inert linear backbone, such as a long saturatedhydrocarbon chain. Such compounds form ordered monolayers onsurfaces, so that the backbone points vertically out of planeof the surface. The friction is then determined by theinteractions between the monolayers, which are weaker than theinteractions between the clean surfaces and this gives a lowerfriction. The fourth paper describes a study on the origin of thedifferences in friction levels between different linerboardsbased on recycled fiber (old corrugated container, OCC). Thesheets were subjected to two extraction stages and analyzedwith respect to surface roughness and their content oflow-molecular-mass lipophilic compounds (LLC). The resultsshowed that a high amount of LLC in the sheets lead to lowfriction, due to lubrication. The fifth paper describes a study that was aimed atdetermining the types of forces that influence the frictionbetween the surfaces of hydrophilic polymers and explaining themechanism by which boundary lubricants decrease the friction.The adhesion and the friction of model systems was measuredwith atomic force microscopy (AFM) using regenerated cellulosefilms and functionalised AFM tips and the effect of fatty acidsand humidity was investigated. The friction significantlyincreased with increasing humidity and that there was a strongcorrelation between the ability of a fatty acid to form ahydrophobic surface and its lubricating performance. Measuredadhesion forces at high humidity were well predicted bytheoretical models that took into account the effect of theLaplace pressure acting in a water meniscus formed aroundcontact regions due to capillary condensation. The resultsindicated that the degree of capillary condensation may beeffectively suppressed by increasing the hydrophobicity of thecontacting surfaces, causing adhesion and friction to decrease.These results suggest that friction between paper surfacesunder ambient conditions is greatly influenced by the degree ofcapillary condensation. Furthermore, lubrication by fatty acidsis achieved by the formation of a vertically oriented,hydrophobic monolayer that can withstand the stresses duringsliding and increase the hydrophobicity of the paper surfaceand thereby suppress capillary condensation. <b>Keywords:</b>Friction, paper-to-paper friction, frictionhysteresis, fibers, orientation, sliding direction, woodextractives, low-molecular-mass lipophilic compounds, boundarylubrication, adhesion, capillary condensation, Laplacepressure, surface forces, JKR theory, gas chromatography-massspectroscopy, X-ray photoelectron spectroscopy, contact angle,atomic force microscopy