Thesis (M.S.)--Humboldt State University, 2009. / Includes bibliographical references (leaves 69-70). Also available via Humboldt Digital Scholar.

Thesis (Ph.D.)--University of Delaware, 2006. / Principal faculty advisor: Mary E. Galvin-Donoghue, Dept. of Materials Science & Engineering. Includes bibliographical references.

Thesis (Ph.D.)--York University, 2005. Graduate Programme in Chemistry. / Typescript. Includes bibliographical references (leaves 160-178). Also available on the Internet. MODE OF ACCESS via web browser by entering the following URL: http://wwwlib.umi.com/cr/yorku/fullcit?pNR11543

Dissertation (Ph. D.)--University of Akron, Dept. of Polymer Science, 2006. / "May, 2006." Title from electronic dissertation title page (viewed 10/11/2006) Advisor, Frank W. Harris; Committee members, Stephen Z. D. Cheng, David A. Modarelli, Judit Puskas, William J. Brittain; Department Chair, Mark D. Foster; Dean of the College, Frank N. Kelley; Dean of the Graduate School, George R. Newkome. Includes bibliographical references.

Prepared under contract no. EX-76-A-01-2295-037.

abstract: This comprehensive library of photovoltaic functions (PVSimLib) is an attempt to help the photovoltaics community to solve one of its long-lasting problems, the lack of a simple, flexible and comprehensive tool that can be used for photovoltaic calculations. The library contains a collection of useful functions and detailed examples that will show the user how to take advantage of the resources present in this library. The results will show how in combination with other Python libraries (Matplotlib), this library becomes a powerful tool for anyone involved in solar power. / Dissertation/Thesis / Python library source code / Masters Thesis Electrical Engineering 2018

The purpose of this investigation is to compare high frequency to low frequency (50Hz) technologies. To accomplish this, two highly optimized candidate converters are built to champion each of the inverter classes. Both candidates are constrained to produce the same quasi-sinusoidal output waveforms in identical operating conditions. The low frequency inverter is designed with optimization of its output power quality and accurate loss characterization taken in mind. A new iron core design procedure is proposed that may predict core losses when using non-sinusoidal excitation. Experimental results indicate that it has a promising degree of accuracy. The high frequency candidate is designed using planar integration technology. A topology selection determines that a critical-conduction mode flyback is the most suitable option. Components are added the topology to allow resonant switching for reduced switching losses. Common-mode current arising from good capacitive coupling between windings in the planar coupled inductor is reduced using charge balancing technology. The novelty of the converter lies is in the fact that all passive components, barring the bulk of the input capacitance and the output capacitance, are incorporated into the single planar structure. Finally, a comparison of the inverters is made in the categories of power quality, regulation, efficiency, robustness and applicability to the application. The high frequency inverter is found to promise substantial advantages over the low frequency variety in most of these elements. / Dr. I.W. Hofsajer

Photovoltaic (solar electric) technology has shown significant potential as a source of practical and sustainable energy; this study focuses on increasing the performance of photovoltaic systems through the use of improved control and power interfaces. The main objective is to find an effective control algorithm and topology that are optimally suited to extracting the maximum power possible from photovoltaic modules. The thesis consists of the following primary subjects: photovoltaic modelling, the topological study of photovoltaic interfaces, the regulation of photovoltaic voltage, and maximum power tracking. In photovoltaic power systems both photovoltaic modules and switching mode converters present non-linear and time-variant characteristics, resulting in a difficult control problem. This study applies in-depth modelling and analysis to quantify these inherent characteristics,s pecifically using successive linearization to create a simplified linear problem. Additionally, Youla Parameterisation is employed to design a stable control system for regulating the photovoltaic voltage. Finally, the thesis focuses on two critical aspects to improve the performance of maximum power point tracking. One improvement is to accurately locate the position of the maximum power point by using centred differentiation. The second is to reduce the oscillation around the steady-state maximum power point by controlling active perturbations. Adopting the method of steepest descent for maximum power point tracking, which delivers faster dynamic response and a smoother steady-state than the hill climbing method, enables these improvements. Comprehensive experimental evaluations have successfully illustrated the effectiveness of the proposed algorithms. Experimental evaluations show that the proposed control algorithm harvests about 1% more energy than the traditional method under the same evaluation platform and weather conditions without increasing the complexity of the hardware. / Applied Science, Faculty of / Electrical and Computer Engineering, Department of / Graduate

It is estimated that 1.6 billion people today live without access to electricity. Most of these people live in remote rural areas in developing countries. One economic solution to this problem is the deployment of small domestic photovoltaic (PV) systems called solar home systems (SHS). In order to improve the performance and reduce the life cycle cost of these systems, accurate monitoring data of real SHSs is required. To this end, two SHSs typical of those found in the field were designed and installed, one in a rural area of the Eastern Cape of South Africa and the other in the laboratory. Monitoring systems were designed to record energy ows in the system and important environmental parameters. A novel technique was developed to correct for measurement errors occurring during the utilization of pulse width modulation charge control techniques. These errors were found to be as large as 47.6 percent. Simulations show that correction techniques produce measurement errors that are up to 20 times smaller than uncorrected values, depending upon the operating conditions. As a tool to aid in the analysis of monitoring data, a PV performance model was developed. The model, used to predict the maximum power point (MPP) power of a PV array, was able to predict MPP energy production to within 0.2 percent over the course of three days. Monitoring data from the laboratory system shows that the largest sources of energy loss are charge control, module under performance relative to manufacturer specifications and operation of the PV array away from MPP. These accounted for losses of approximately 18-27 percent, 15 percent and 8-11 percent of rated PV energy under standard test conditions, respectively. Energy consumed by loads on the systems was less than 50 percent of rated PV energy for both the remote and laboratory systems. Performance ratios (PR) for the laboratory system ranged from 0.38 to 0.49 for the three monitoring periods. The remote system produced a PR of 0.46. In both systems the PV arrays appear to have been oversized. This was due to overestimation of the energy requirements of the loads on the systems. In the laboratory system, the loads consisting of three compact fluorescent lamps and one incandescent lamp, were used to simulate a typical SHS load pro le and collectively consumed only 85 percent of their rated power. The 8 predicted load profile for the remote system proved to be signi cantly overestimated. The results of the monitoring project demonstrate the importance of acquiring an accurate estimation of the energy demand from loads on the system. Overestimations result in over-sized arrays and energy lost to charge control while under-sized systems risk damaging system batteries and load shedding. Significant under-performance of the PV module used in the laboratory system, underlines the importance of measuring module IV curves and verifying manufacturer specifications before system deployment. It was also found that signi cant PV array performance gains could be obtained by the use of maximum power point tracking charge controllers. Increased PV array performance leads to smaller arrays and reduced system cost.

Semiconductor materials used for making photovoltaic (PV) cells have defects and impurities due to constraints of keeping production costs low. Electrically active defects that are distributed over the bulk material lead to reduced overall performance of a photovoltaic (PV) cell. In this study an adaptable Light Beam Induced Current (LBIC) system was designed in order to characterize the local performance of PV cells. The system uses a laser source and objective lens mounted vertically above the sample on the X-Y stage. Two current pre-amplifiers are used for converting the photo-generated current from the PV cell and the signal from the reflection detector cell into a voltage that can be measured by the data acquisition board. Two configurations for measuring the photo-current maps of either bare cells or encapsulated PV mini-modules can be used. To add flexibility it was envisaged that the system would be built in such a way that it allows easy integration of carrier lifetime mapping capabilities while keeping costs to a minimum. The carrier lifetime measurement technique integrated into the LBIC system is based on the optical Open-Circuit Voltage-Decay (OCVD) method. In a single-crystalline silicon PV cell that was tested, photo-current and opencircuit voltage LBIC scans revealed shunting behaviour due to scratch marks on the front surface. The marks are believed to have been caused by poor handling during manufacturing process. Reduced photo-current due to edge shunting was observed towards the edges of the PV cell. In another sample of single crystalline silicon cell an edge shunt resulted in a 30 percent drop in photo-current measured. LBIC measurements performed on multi-crystalline cells revealed nonuniformities such as enhanced photo-current on one side of grain boundaries. These asymmetric enhancements of local photo-current are attributed to the incline of the grain boundary into the bulk of the material. LBIC results obtained from mini modules showed a high degree of mismatching from cell to cell. It is well known that mismatching can degrade the performance of a PV module with series connected cells. The LBIC measurements presented also illustrated the negative effects of delamination on the photo-current of PV modules. The LBIC measurements performed on mini PV modules highlight some of the benefits of using an LBIC technique as a tool for investigating PV cell’s local photo-current response. The effective lifetime maps obtained highlight the importance of optical OCVD method as a tool that can be used in conjunction with conventional LBIC technique. Effective minority carrier lifetimes around 40 ms were measured on a single crystalline silicon cell of 2.5 x 2.5 cm2. Local features such as cracks and lifetime degrading defects were revealed by LBIC maps and were also confirmed on effective lifetime maps. The results presented demonstrate the importance of using effective carrier lifetime maps to complement photocurrent maps of PV cells and identification of areas where defects are located.